EM
-
Product
PathWave EM Design (EMPro)
-
Electromagnetic (EM) simulation brings you insight before physical prototyping. Customize EM simulations for speed and accuracy. Integrate EM analysis with your circuit simulations.
-
Product
Whole Body EM Phantoms
EM - PHANTOM
-
Schmid & Partner Engineering AG
The POsable Phantom for Electromagnetic sYstems Evaluations (POPEYE) is an anatomically correct human phantom based on a torso shell w/ head with posable arms, hands and legs. This radio frequency (RF) human has been designed to meet the requirements for test configurations for which the effects of the body on the EM performance cannot be neglected, such as operating tablet and laptop computers and other body-mounted transmitters. With a simple adjustment (one tightening screw), the arms, hands and legs can be positioned accordingly for conducting simulations of any usage or operation (standing, sitting, arms raised, talking position, etc...).
-
Product
Electromagnetic (EM) Speed Log System
AGILOG 2
-
Aeronautical & General Instruments Ltd.
Developed for use on surface warships and submarines, AGILOG 2 sets the standard for accurate and reliable measurement of ship’s speed through the water, an essential element in navigation and weapons system integration.
-
Product
Time-domain Field-Device-Circuit coupled simulator
EM-SUPREME®
-
Time-domain Field-Device-Circuit coupled simulator for modeling of passive structures, active components, and complete RF & millimeter-wave modules. EM-Supreme is used for EM modeling of power amplifiers, switches, filters, active antennas, and complete RF modules such as antenna-switch, switch-filter, switch-filter-amplifier, and front-end modules with no approximations.
-
Product
Cable Harness EM Solver
MHARNESS
-
Electro Magnetic Applications, Inc.
MHARNESS to Complete the Last Mile of EM Coupling Simulation Traditionally, electromagnetic effects simulation has focused on the transients induced on the overall cable bundle of complex systems. MHARNESS is a transmission line solver that reveals the EM transients on the most critical element of systems: the pin interface to electronics systems. Now, EMA3D and MHARNESS can co-simulate in one self-consistent simulation.
-
Product
Electron Multiplication (EM) Standard Image Sensors
-
EM (Electron Multiplication) is a technology that uses on-chip gain in the charge domain to effectively eliminate read noise from an image sensor. This enables advanced ultra-low light applications that require extreme sensitivity at fast frame rates. Examples include life science applications such as single molecule detection, super resolution microscopy and spinning disk confocal microscopy along with physical science applications such as nanotechnology imaging, Bose Einstein condensates and soft X-ray spectroscopy, and astronomy applications such as adaptive optics and lucky imaging. The inclusion of an additional conventional output allows further flexibility for applications such as true 24 hour surveillance.
-
Product
Interference & Compatibility Evaluation System
ICEy
-
Schmid & Partner Engineering AG
ICEy is the most advanced reactive near-field E/H-field scanning system for the analysis of EM interference and compatibility (EMI/EMC) in highly integrated electronics. ICEy is the only system that provides accurate EM measurements traceable to international calibration standards and also allows independent interlaboratory comparability of EMI/EMC measurement results.
-
Product
Antenna, Log Periodic
EM-6956 | 500 MHz – 3 GHz
-
The Electro-Metrics EM-6956 Log Periodic Antenna operates over the .5-3 GHz frequency range. The broadband frequency capacity of the EM- 6956 eliminates the need for band switching, element extension or external tuning.
-
Product
Navigation Information System
Nav-IS
-
Aeronautical & General Instruments Ltd.
Nav-IS combines a single or dual axis EM Speed Log with a range of Meteorological System options for a low cost, integrated solution. Using the latest proven and in service solid state sensor technology, this innovative, cost-effective and accurate system has been specifically developed for all applications from ocean-going merchant and passenger vessels to offshore patrol, coastguard and naval support vessels.
-
Product
IQ Demodulator
IQD Series
-
*Capable of receiving RF and LO frequency inputs *Output from DC to 500 MHz *Internal low noise oscillator Internal reference *Buffered demodulator *Balanced IQ *Optimized for low EVm *Optional internal Reference Detect Switch (EM Research RDS Series) *Up to 250 mega-symbols per second
-
Product
RF Architectural Shielding Products
-
EMI (Electromagnetic Interference) is often used interchangeably with RFI (Radio Frequency Interference). However, EMI can be any frequency of electromagnetic noise, whereas RFI is a relatively narrow range of electromagnetic noise on the EM spectrum. EMI Shielding can be used to mitigate electric and magnetic radiation across various spaces. Radio Frequency (RF) Shielding can be used to mitigate RFI with specifically designed enclosures that can block RFI. As well, RF Shielding can include application of RF Shielding paints, fabrics, and other materials.
-
Product
Clarity 3D Solver
-
The Cadence Clarity 3D Solver is a 3D electromagnetic (EM) simulation software tool for designing critical interconnects for PCBs, IC packages, and system on IC (SoIC) designs. The Clarity 3D Solver helps designers tackle the most complex electromagnetic (EM) challenges when designing systems for 5G, automotive, high-performance computing (HPC), and machine learning applications with gold-standard accuracy.
-
Product
TEM Cells
-
Transverse Electro Magnetic (TEM) cell or Crawford cell (named after its inventor) is used to generate accurate electromagnetic waves over a wide frequency range: DC (0 Hz) to GHz., EM waves generated in the cell propagate in transverse mode and have the same characteristics as a plane wave. It can be used to calibrate E-field broadband probes for testing radiated E-field immunity as well as for measuring radiated emission from a product with a spectrum analyzer/EMI receiver.TEM cell generates a consistent electromagnetic field for testing small RF devices such as wireless pagers, receivers, portable phones, etc.
-
Product
Propagation Software
Wireless InSite
-
Wireless InSite is a suite of ray-tracing models and high-fidelity EM solvers for the analysis of site-specific radio propagation and wireless communication systems. The software provides efficient and accurate predictions of EM propagation and communication channel characteristics in complex urban, indoor, rural and mixed path environments.
-
Product
EM Solver System Level Solver
EMA3D
-
Electro Magnetic Applications, Inc.
MA3D is a powerful 3D numerical solution of Maxwell’s curl equations based on the time-domain finite-difference method in rectangular coordinates. The code has application to nearly any EM coupling, radiating, or interaction problem. EMA3D’s FDTD approach is the only EM tool capable of capturing the detail of entire aerospace or ground systems down to individual electronics interfaces in a computationally accessible manner. Computational advances and parallelization allow for fidelity once only dreamed possible.
-
Product
3D/2.5D Time-Domain Electromagnetic Field Solver Software
EM-CORE ®
-
3D/2.5D Time-Domain Electromagnetic Field Solver Software for Planar-Circuit and Antenna Simulation. 3D & 2D Radiation Patterns Modeling, Spiral Inductors Modeling, 3D EM Modeling of Filters, Intuitive Geometry Build, and more!
-
-
Product
EM Clamps
-
The EM Clamp or a Bulk Current Injection Probe (BCIP)can be used for IEC/EN 61000-4-6 tests on ports/cables for which no Coupling/Decoupling Network (CDN) is available.
-
Product
EMF Measurements/EM Measurements/Electromagnetic Radiation
-
Holland Shielding Systems B.V.
Electromagnetic fields cause interference in electronic devices and may affect the health of people close to where the fields are generated. It is important to recognize this at an early stage in a construction process, for instance at a future construction location or while construction is already underway, so that budgets are not exceeded. By means of field-strength measurements one can chart the existing electromagnetic fields and radiation emitted by GSM, UMTS antennas and transformer spaces, to mention a few examples. These measurements can help determine the best location in the new building for rooms where sensitive measurements are to take place, e.g. in hospitals or nano laboratories. And last but not least, field-strength measurements can detect sources of interference and can be part of a scheduled check of existing screened spaces and Faraday cages.
-
Product
Antenna Simulation
EM Twin
-
In today's world of high-frequency technology, precise simulations are of crucial importance. With EM Twin, IMST offers a pioneering software tool that has been specially developed for the simulation of antenna digital twins.
-
Product
Electromagnetic Simulation Software
EmSlice
-
EMSlice is an EM Simulation Software tool supporting the design, analysis, testing and evaluation of systems involving EM Radiation. Including optical, radio communications, radar, antenna systems, etc.
-
Product
Logger version 2-D electro-magnetic current meter
INFINITY-EM AEM-USB
-
Infinity EM is an autonomously deployable EM (electro-magnetic) current meter with a data logger. Due to the principle, the instrument provides high accurate 2-D current measurements in even low scatter fields, where ADVs (Acoustic Doppler Velocimeter) has difficulties. The measurement range is wide from 0 to ± 500 cm s-1. The instrument design is compact (1.0kg in air). Infinity EM allows for current velocity measurements virtually anywhere.
-
Product
Electromagnetic
Promis 10
-
The Promis device is a multi-frequency, multi-spacing 3 component slingram type EM System for sounding and profiling the soil. This system features a transmitter loop to produce a primary magnetic field that will induce eddy current in conductive materials. These eddy currents will generate a secondary magnetic field that will be measured with the receiver loop. This system measures the in-phase and the out-of-phase components of the secondary magnetic field.
-
Product
WIPL-D Pro
-
WIPL-D kernel is unique in many ways, allowing the most efficient full wave EM simulations. It is based on the Method of Moments (MoM) but applied to quadrilateral mesh elements. In addition, the basis functions are HOBFs (Higher Order Basis Functions) which means up to 2 lambdas large mesh elements. The electrical size of problems is expressed in number of unknowns, rather than in mesh elements. The quad mesh offers two times less unknowns than the traditional triangular one, while using HOBFs reduces number of unknowns several times.
-
Product
Circuit Synthesis Software
Optenni Lab
-
Optenni Lab™ is the leading circuit synthesis software for antenna optimization aiming at efficient assessment and optimization of antenna systems at any design phase. Optenni Lab features automatic matching circuit synthesis and optimization, antenna array beamforming with active impedance control, and many supplementary assessment tools. Optenni Lab is often used in conjunction with EM simulators, and several links are provided with major EM tools on the market.
-
Product
Electromagnetic Field Simulator
EMPIRE XPU
-
EMPIRE XPU is an outstanding 3D time-domain EM modelling tool for antennas, microwave circuits, EM chip design and more. It is based on the powerful Finite Difference Time Domain (FDTD) method, which has become the industry standard for RF and microwave component and antenna design.
-
Product
Ultra Low Level DC Voltage Amplifiers
-
The EM A10 is a low level amplifier module for sensitive measurements, data collection and systems, where signals below 1 nanovolt may be measured. It is ideal for the input unit for precision voltage measuring systems, requiring voltage sensitivity for measuring low noise and low impedance sources. The noise level of the A10 is equivalent to a perfect resistor of about 20 ohms. When used with a digital voltmeter, steady one nanovolt digits may be displayed, with a response time constant of less than a second. The input voltage stability of the A10 is very high, with the drift around a nanovolt per degree C. The input connectors are made from pure copper. The input impedance is very high, and is time dependent, determined by the loop gain.
-
Product
Operator Interfaces
-
Watlow Electric Manufacturing Company
Watlow offers reliable, affordable, easy-to-use interfaces for machines and systems. The Silver Series EM touchscreen operator interface terminals feature e-mail, USB, data logging, password security and multiple languages. The EZ-ZONE RUI remote user interface fits in tight spots, its EZ-Key reduces repetitive tasks to one touch and the gateway options connect EZ-ZONE products with other automation equipment and software. Paired with Watlow controllers, these interfaces are the perfect solution for process and machine control applications.
-
Product
IQ Modulator
IQM Series
-
*Capable of receiving from DC to 500 MHz, LO inputs, outputting RF frequencies *Internal low noise oscillator *Internal reference *Buffered modulator Balanced IQ *Optimized for low EVM *Internal Reference Detect Switch Optional (EM Research RDS Series) *Up to 250 mega-symbols per second
-
Product
Handheld 1-D electro-magnetic current meter for rivers
AEM1-DA
-
AEM1-DA is a 1-D electro-magnetic (EM) current meter for the flow measurements in rivers, streams and various waterways. The measurement range is 0 to 5m s-1. The EM sensor can accurately measure water speeds at a shallow depth of 3cm. The display unit has a 2MB flash memory so that the data are saved with calendar information (up to 255 station data). In comparison with conventional propeller-type current meter, AEM1-DA is robust and extremely easy to be operated and maintained.
