Insulation Oil
measures the breakdown voltage of insulating oils.
-
Product
Insulation Testers
-
Sanwa Electric Instrument Co., Ltd
Is a spot insulation test which uses an applied DC voltage (typically either 250Vdc, 500Vdc or 1,000Vdc for low voltage equipment <600V and 2,500Vdc and 5,000Vdc for high voltage equipment) to measure insulation resistance.
-
Product
Dielectric Oil Testers
-
Electrical insulation oils form the critical insulation medium for many of today’s electrical apparatus, such as transformers, tap-changers, circuit breakers, cables, bucket trucks etc.
-
Product
True RMS Digital Insulation Multimeter
Model KM 877
-
Kusam Electrical Industries Limited
• VFD V & Hz readings.• Paper White Backlight LCD Display• Record MAX / MIN readings.• Display Hold Function.• Dual Digital Display.• PI & DAR Function.• Autoranging.• Pass /Fail Insulation Resistance Compare function; 12 selectable Preset Values.• LOCK-Test mode for Insulation Resistance & Earth Continuity Test.• BeepJack ™ audible & visible input warning.• Remote Probe for insulation Resistance & Earth Continuity Test.• Functions : DC/AC Voltage , VFD AC Voltage, Insulation Resisitance, Resistance, Earth Continuity Test, Hz Line Level Frequency
-
Product
PID Insulation Tester
TOS7210S
-
The PID insulation tester (TOS7210S) is designed based on the insulation resistance tester (TOS7200) to carry out the evaluation of the PID (Potential Induced Degradation) effect of the PV module precisely and efficiently. Being equipped with the output ability of 2000 V and the ammeter with nA resolution as well as a polarity switching function, the TOS7210S is also applicable not only to the PID evaluation but also the evaluation of the insulators that requires a high sensitivity of measurement. The tester is equipped with the panel memory that is externally accessible and RS232C interface as standard; it can be flexibly compatible with the automated system.
-
Product
Energized Distribution Insulator Tester
-
A sensitive voltmeter, the tester measures the difference in potential across each insulator in a suspect string. Comparative readings from satisfactory strings in the same operating situation quickly indicate the state of every insulator in the string being tested.
-
Product
Oil Resistivity Test System / Million Meg Ohm Meter (MM1)
OTD-45
-
UDEYRAJ ELECTRICALS PRIVATE LIMITED
Model : OTD-45OTD-45 is single self contained unit containing oil test cell, high frequency induction heating with temperature controller/sensor; dielectric loss measuring bridge, AC test voltage source, SF6 filled standard capacitor; high resistance meter; DC voltage source and all digital circuits.
-
Product
Digital Insulation Tester
200M
-
Laxtronics Instruments & Controls Pvt. Ltd
Digital insulation tester Model No: DIT200M is designed to carry out electrical insulation measurement in delicate or sensitive electronic sensors, transducers, modules and assemblies with test voltage from 1 to 30 Volts DC, its short circuit current is less than 100uA. The instrument can measure Resistance from 1 Meg Ohm to 1000 Meg Ohms.
-
Product
Insulation Resistance Tester
250-1000V
-
Wuhan Fanke Transformer Manufacture Co., LTD
Professional Insulation Resistance Tester, 250-1000V
-
Product
Multimeter w/ Insulation Measurement
HT701
-
Professional TRMS multimeter with 10.000 measuring spots and measurement of insulation resistance with selectable test voltage between 50, 100, 250, 500, 1000VDC.
-
Product
Insulation Measuring Device According to DIN EN 61557-2 (VDE 0413-2)
-
PeakTech Prüf- und Messtechnik GmbH
This digital insulation measuring device is required for various measurements of cables, components and their insulation.
-
Product
X-ray Fluorescence Sulfur-in-Oil Analyzer
SLFA-6000
-
HORIBA Scientific, a market leader in sulfur-in-oil analysis, announces the launch of the new SLFA-6100/6800 Energy Dispersive X-ray Fluorescence Analyzer, which measures sulfur in oil ranging from 5 ppm to 9.9999%. This new, compact, and accurate analyzer meets the needs of anyone wishing to conform to ASTM D4294, ISO 8754 or JIS K2541/B7995.
-
Product
5kV Insulation Resistance Tester
KV3122
-
KV Hipot Power Test Equipment Co.,Ltd
KV3122 Insulation Resistance Tester is suitable for measuring the resistance of various insulating materials and the insulation resistance of transformers, motors, cables and electrical equipment. Digital insulation resistance meter is composed of medium and large scale integrated circuits, including high-precision micro current measurement system, digital boost system and automatic discharge circuit.
-
Product
Low Voltage Insulation Tester
AD-801
-
3 Measurement voltage ranges: 4 V, 10 V, 100 V, LCD display 3,5 digits, Autoranging, Insulation measurement up to 20 G W, LED indicator for units k W , M W and G W, Switch of choice measuring voltage 10 V and 100 V,
-
-
Product
40U (70") Insulated Bus Bar
BB-70-I
-
40U (70") insulated bus bar provides cabinets with recessed rail option and a convenient, isolated common grounding mechanism.
-
Product
Analog And Digital Insulation Testers
-
High AccuracyRange Selection & Single Person Push Button OperationLCD Back Light Function with Indicator SwitchData Holding Function, Function Icons on DisplayMeasurement of AC Voltage upto 600VACMeasurement of Phase Sequence between (Phase-PhaseVoltage)with LED Indicator Auto Range (Insulation Test)LED Indicator for High VoltageInbuilt Protection Circuit to prevent the harm of reverse voltagesBattery Operated with AC Adaptor3 Ranges of Voltage & Insulation Resistance
-
Product
Electrical Insulation Tester Kit with Dual Display
420001
-
When undertaking power installations, the 420001-insulation tester can provide special help to test wiring. This unit can provide 125V,250V, 500V and 1000V source for the test, and under each range it can supply 1mA current to feed the capacitance load. With the auto-range function, it can measure up to 4,000 Megaohm with the resolution of 1Kohm.
-
Product
Insulation Resistance Tester
-
Aarohi Embedded Systems Pvt. Ltd
Aarohi make device enable us to measure electrical leakage in wire, results are very reliable as we shall be passing electric current through device while we are testing. The equipment basically uses for verifying the electrical insulation level of any device such as motors, cables, generators, windings, etc.
-
Product
Dielectric Insulation Analyzer
DIRANA
-
DIRANA uses dielectric frequency response (DFR) analysis in order to determine the condition of high-voltage insulation systems such as those in power transformers, bushings, cables and generators.
-
Product
High Voltage Insulation Tester
505
-
Simpson's Model 505 High Voltage Insulation Tester is capable of measuring insulation resistances from 10 kilohms to 1 teraohm with eight selectable test voltages up to 5000 V. As a safety feature, the insulation tester acts as an AC/DC voltmeter to measure the absence of voltage in networks up to 2000 V.
-
Product
Shoe Heat Insulation Tester
UI-FT08
-
Shoe Heat Insulation Tester – Thermal Insulation Tester is used to test shoe heat insulation / thermal insulation against hot performance. Place the shoe in sandbath and the footwear shall contact with the plate(forepart and the heel) in certain temperature for a given period. Then to measure the temperature increase inside of the shoe. The contact temperature and time is specified in production standard.
-
Product
High Frequency Insulation Tester
HFIT 8.0
-
The MEDTEQ HFIT 8.0 is intended for high frequency insulation testing against IEC 60601-2-2. This version includes in-built metering and automatic functions to make testing easy not only for design and laboratory testing, but also suitable for regular production testing.
-
Product
Oil Tan Delta Tester
OTD
-
The Oil Tan Delta (OTD) is a laboratory instrument, which measures the Tan Delta, Resistivity and Relative Permittivity of insulating liquids. These tests give a wider picture of the overall quality of the insulating oil, and will indicate if there is any contamination. Megger has developed features of the OTD to ensure that productivity levels within laboratories are maximised. The microprocessor controlled inductive heater means that there is uniformity of temperature throughout the cell, in compliance with IEC 60247, and for cooling a fan effectively speeds up the cell cooling time. The instrument has a temperature measuring range of 10 to 110 C, with an accuracy of 1 C. It can be set to preheat before testing takes place. The automated oil drain facility negates the need to move the oil vessel. User safety is paramount and with this in mind, Megger have designed independent and dual redundant high voltage cut-off circuitry. If for any reason the user needs to abort the test, this can be done so by pressing any key, immediately terminating the test and removing the high voltage. The design of the cell components maximise oil fill rate but minimise turbulence in oil flow and eliminate trapping of air. With only 32 cell components, it is easy to assemble and disassemble.
-
Product
PE/ Ground, Insulation Resistance Tester
Handheld
-
The safety testers of the Handheld class are used to measure PE/ Ground resistances, insulation resistances and to perform a simple functional test. The small and sturdy universal testers are intended for standard-compliant safety tests in workshops and production as well as for mobile operation during repair, installation, service and more.
-
Product
Oil Test Equipment
-
KV Hipot Power Test Equipment Co.,Ltd
oil analysis program is to verify that a lubricated machine is operating according to expectations. When an abnormal condition or parameter is identified through oil analysis, immediate actions can be taken to correct the root cause or to mitigate a developing failure.
-
Product
Automatic Liquid Interface Tension Meter,Surface Tension Analyzer,Oil Interface Tension Meter
-
Chongqing Assen Power Equipment Co., Ltd
Our HTID-1 Automatic Interface Tension Tester is used to test various liquid surface tension and interface tension based on the ring method that is simple and high accurate, which is widely applied in electric, petroleum, chemical, medicine, food, and teaching filed.
-
Product
Insulation Tester
1kV Megohmmeter
-
*Calculations (automatic)*Potential Index and Dielectric Absorption Ratios*Tests Continuity, Resistance and Frequency Measurements*Programmable Alarms*Insulation Test, Resistance, Continuity*Hazardous Voltage Alert (Icon) if voltage is >70 volts 5.) On Board Timer, +1/- 1 sec
-
Product
Oil Acidity Tester
-
Weshine Electric Manufacturing Co., Ltd
Automatically complete the operations of extractant addition, neutralization titration and end point discrimination, acid value calculation, data storage and print output.
-
Product
Oil Surface Tension Tester
-
Weshine Electric Manufacturing Co., Ltd
Surface tension is a measurement of the cohesive energy present at an interface. The molecules of a liquid attract each other. The interactions of a molecule in the bulk of a liquid are balanced by an equal attractive force in all directions. Molecules on the surface of a liquid experience an imbalance and cohere more strongly to those directly associated with them on the surface.
-
Product
Modeling Capacitors, Inductors, Insulators, Coils, Motors, and Sensors
AC/DC Module
-
The AC/DC Module is used for simulating electric, magnetic, and electromagnetic fields in static and low-frequency applications. Typical applications include capacitors, inductors, insulators, coils, motors, actuators, and sensors, with dedicated tools for extracting parameters such as resistance, capacitance, inductance, impedance, force, and torque.
