-
Product
PCI Resistor Card 2-Channel 2 Ohm To 32.7k Ohm
50-293-032
Programmable Resistor Module
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
ARINC 429 Test & Simulation Interface for PCI Express
PCIe-C429X
Simulator
Avionics Interface Technologies
16, 32, or 64 ARINC 429 Channels (up to 32 Tx & 32 Rx) - Programmable Tx channel output amplitude - Programmable High/Low Speed Operation - Eight (8) Discrete I/O (Four (4) inputs, and four (4) outputs) - Concurrent operation of all Tx/Rx Channels at high data rates - Full error injection and detection - Data capture filtering, 100% bus recording, and physical bus replay - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B time code encoder/decoder with free-wheeling mode - Application Interface supporting C/C++, C# and VB.NET Development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
PCI High Density Resistor Card 5-Channel, 16-Bit, 0 To 65k Ohm
50-295A-021-5/16
Programmable Resistor Module
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
DG I/O Backplane Extender Board
9286-1015
-
15" x 15" Backplane Adapter. Not to be used in production environment. Used with any I/O bus adapter during installation of Hawk system. Presents Nova/Eclipse bus signals on dual 50-pin connectors. Two 10 ft. (3 m) ribbon cables included.
-
Product
VME Form Factor Extender, 6U, 120mm
111FFE6012-012X
-
The VME form factor extender 6U 120 mm allows to adapt boards for use in the same VMEbus system. It maintain the correct depth dimensions and allow the front panel to be aligned.
-
Product
Dual-Site Single-Slot 6U Compact PCI (cPCI) PMC Adapter/Carrier
6332
-
Our Dual-Site Single-Slot 6U Compact PCI (cPCI) PMC Adapter/Carrier 32-Bit/66 MHz (6332) adapts two single-wide PMCs to a cPCI slot. At the heart of the carrier is a 6150 PCI-to-PCI bridge that connects the carrier's internal PCI bus to the cPCI backplane.
-
Product
8-Slot 64-Bit 6U Compact PCI Backplanes
cBP-6418U
Backplane
- 1 Segment: 1 system + 7 peripheral slots- cPCI BUS: up to 64-bit/66MHz- Power connectors: ATX connector x 1 DC Screw terminals
-
Product
PCI Express UltraScale+ FPGA Carrier Board With FMC+ Site, X16 PCIe Gen 4
PG4+
-
The PG4+ continues DEG’s commitment to delivering high performance processing solutions for mission critical applications requiring the latest in AMD UltraScale+ FPGA computing power. The PG4+ is a PCI Express, standard form factor, FPGA processor board designed to meet the needs of challenging, embedded high-performance digital signal processing applications. The AMD UltraScale+ VU37P or VU47P delivers superior processing capabilities and supports operations such as: FFTs, FIR filters, fixed-point and repetitive processing tasks. The PG4+ FPGA node processes input from the FMC HPC + (Vita 57.4) site, allowing for maximum application configurability and performance when coupled with DEG’s market leading ADC and DAC FMC modules that operate up to 12 GSPS.
-
Product
PCI Express, Power, USB Cables for Amfeltec Products
-
PCI Express, Power, USB Cables for Amfeltec Products
-
Product
PCI Express Digital I/O Cards
-
Sealevel PCI Express digital I/O cards are designed for computers with X1 PC Express slots and are compatible with any PCI Express slot. Digital I/O cards are currently available with optically isolated inputs and Reed relay outputs. Optically isolated inputs protect the PC from voltage spikes common to industrial environments while Reed relay outputs provide reliable, long-life switch closures suitable for low current applications.
-
Product
PCI Express Full Tx Test Suite
SW02PCIE
-
The PCI Express Full Tx Test Suite is part of the subscription based Oscilloscope Compliance Test Software Suites. In addition to Tx Validation licenses for PCIExpress, this suite also provides the support of the Advanced PCIe Protocol Decode/Trigger Software. This suite supports coverage across the PCI Express technology starting from Gen4. Together with the subscription model, this enables the support and coverage continuity as the PCI Express technology progresses through generations.
-
Product
Flexible x4 PCI Express to 4 MiniPCI Express Splitter
SKU-072-0X
-
Flexible x4 PCI Express to 4 MiniPCI Express Splitter (Splitter) was designed to expand modern motherboard (ATX, mini ATX etc.) that have PCI Express interface. It allows connecting up-to four MiniPCI Express add-in expansion boards to the standard motherboard PCI Express connector.Splitter includes 4 MiniPCI Express Adapter boards, x4 PCI Express Host board and 4 Flat PCI Express Cables.
-
Product
PCI Data Acquisition Boards
AD8-650X2DMA Series - 8 bit, 800MS/s
-
Model AD8-650X2DMA is similar to the AD8-1250DMA, but contains two simultaneous-sampling A/D channels, each capable of sampling at up to 800 MS/s.
-
Product
Mini PCI Module
MPCI-1553-DDC
Controller
The ALPHI MPCI-1553-DDC uses the BU-65864 communication device as its 1553 bus controller, or remote terminal, or monitor terminal. A single controller has two redundant channels and built in transceivers. The controller has internal transceivers for both channel A and B. The Mini PCI board has on-board transformers for both channels. The board format is a Mini PCI boardlayout.
-
Product
Single Bus 36-Channel 2A PCI Fault Insertion Switch
50-190-201
Fault Insertion Unit
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
-
Product
PCI Programmable Resistor Card 2-Channel 3 Ohm To 131k Ohm
50-294-034
Programmable Resistor Module
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Passive XMC-to-PCI Express Adapter
5944
-
The Technobox, Inc. P/N 5944 is designed to adapt a single-wide XMC card to a 16X PCI Express slot. The 5944 supports both P15 and P16 and allows access to PN4 signal via the adapter's DIN connector. The A and C rows of a 96-pin DIN connector connect with the 64-pin user I/O connector (J4/P4) on the mezzanine card, permitting internal connection of rear I/O.
-
Product
2-port 10GbE PoE PCI Express Card
AX92324
-
Intel® Ethernet Controller X550-AT2, up to 10 Gbps data rate, Supports 15.5KB Jumbo Frame and IEEE 1588, Compliant with IEEE802.3at to deliver 25.5W per port, PCI Express x4 compliant, PoE power on/off via Power Manager software and API, Operating temperature range from 0°C to 55°C
-
Product
PCI 8 Form C Relay Output / 8 Isolated Input Digital Interface
8011
-
The 8011 digital I/O interface provides 8 optically isolated inputs and 8 Form C relay outputs. The inputs protect the PC and other sensitive equipment from spikes and ground loop current that can be generated in industrial environments, while the outputs provide higher current capabilities (up to 2A) and are optimized for 24V operation.
-
Product
Vita42 Compact PCI PICMG 2.16 Blade
CP6007-RA
-
CP6007-RA is based on a sixcore Intel® Xeon® processor with 10nm technology, with outstanding performance-per-watt values. Its scalable power budget allows users to tailor the power dissipation to their requirements. 32GB soldered memory with ECC is provided.
-
Product
VME PCI Express Crate Controller
V120
-
The V120 is a VME bus master crate controller, usable as a crate slot 0 arbiter or as a secondary controller. Each PCI Express cable driver board, in a PC backplane, can drive one to four V120s over standard, flexible PCI Express cable assemblies up to 7 meters long.
-
Product
PCI Single 22 X 8 Matrix 1 Pole Screened
50-512-021-S
Matrix Switch Module
The 50-510 series of matrix cards feature a wide range of selectable switching configurations (22x4,dual 20x4,22x8 and 44x4). Larger matrices may be constructed by Daisy Chaining the common signals from multiple PCI cards. For example four 44x4 Cards will form a 176x4 Matrix, a total of 704 crosspoints. Expansion cables are available for the 50-512 and 50-513: The 50-512 can be expanded to 44x8 or the 50-513 can be expanded to 88x4 using two cards linked by the ribbon cable assembly 50-976-020-0.1M. Also the 50-512 can be expanded to 22x16 or the 50-513 can be expanded to 44x8 using two cards linked by the ribbon cable assembly 50-976-050-0.1M.
-
Product
4-Ch 1.25 GHz, 16-bit D/A with DUC, Extended Interpolation, Virtex-6 - 3U VPX
Model 52671
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Four 1.25 GHz 16-bit D/As- Four digital upconverters- Programmable output levels- Extended interpolation range from 2x to 1,048,576x- 250 MHz max. output bandwidth- 2 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- Dual µSync clock/sync bus for multimodule synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- 3U VPX form factor provides a compact, rugged platform- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (Open VPX™ System Specification)- Ruggedized and conduction-cooled versions available- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
Product
Dual-Channel, Tri-Port Per Channel, for Extended Cabling up to 20 Meters
FW1
-
The FW1 provides IEEE 1394 (Firewire) high-speed serial communications. The module is provided with a direct PCIe interface to the local (on-board) processor, or, an external host processor for board platforms that support external PCIe connectivity. These module(s) are not supported with the classic memory register-based NAIBrd Software Support Kit (SSK) API libraries. These communication function modules support device control and management via standard native OS (Linux) FireWire device driver.
-
Product
cRIO-9065, 667 MHz Dual-Core CPU, 512 MB DRAM, 1 GB Storage, Zynq-7020 FPGA, Extended Temperature, 4-Slot CompactRIO Controller
783832-02
Controller
667 MHz Dual-Core CPU, 512 MB DRAM, 1 GB Storage, Zynq-7020 FPGA, Extended Temperature, 4-Slot CompactRIO Controller - The cRIO-9065 is a rugged, fanless, embedded controller that you can use for advanced control and monitoring applications. This software-designed controller features an FPGA, a real-time processor running the NI Linux Real-Time OS, and embedded user interface capability. The cRIO-9065 features an SDHC slot and a variety of connectivity ports, including two tri-speed RJ-45 Gigabit Ethernet, one USB host, one USB device, and one RS-232 serial. Additionally, the cRIO-9065 supports an extended temperature range. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
Product
Single Rear Slot Universal Low-Profile PCI to Compact Flash Adapter
P312
-
To cater for the latest generation of Low Profile PCs that can only use Low Profile PCI add-in boards, Elan has created the P312. This model, from the P-Series range, features a Compact Flash Type II ejector and a circuit board that conforms to the MD1 profile specification. It will allow you to use any Compact Flash card such as IBM MicroDrives, Bluetooth cards, WLAN 802.11b cards, data acquisition cards, pager cards, GPS cards etc.
-
Product
PCI Express Interface Card
MPCIE2-1553
Interface Card
he MPCIE2-1553 is a mini PCI Express Full-Mini Type 2 Interface Card for 1 or 2 MIL-STD-1553 channels in an incredible small package. The MPCIE2-1553 implements the latest MIL-STD-1553 32-bit FPGA Protocol Engine Technology (AltaCore-1553) with the industry leading Multi-Layer Software development software package (AltaAPI).
-
Product
PCI-5153, 500 MHz Bandwidth, 2 GS/s, 8-Bit PCI Oscilloscope Device
780318-01
Oscilloscope
500 MHz Bandwidth, 2 GS/s, 8-Bit PCI Oscilloscope Device - The PCI‑5153 high-speed oscilloscope device has two channels that sample up to 2 GS/s with flexible settings for coupling, voltage range, and filtering. Oscilloscope devices also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for applications with fast signals that require up to 500 MHz of analog bandwidth and flexible measurement configurations.
-
Product
PCI Evaluation Board
BCM91250E
-
The BCM91250E is a full-length PCI evaluation board with the SiByte® BCM1250 dual-processor System on a Chip. The board is designed for software development and for developing PCI applications that require high-performance processors.
-
Product
Value-added Module With COM/CAN/DIO And 3 PCI Express Mini Card Slots
VAM900
-
*1 4-wire isolated RS-232/422/485, 1 isolated CANBus 2.0A/B, 1 isolated DIO 8-in/8-out*Swappable modular design*Maximize I/O flexibility*2kV (COM & CANBus)/1.5 kV (DIO) isolated protection*Designed for tBOX300/500 series*EN 50155 certified; CE, LVD and FCC compliant
