-
Product
1-Port PCI Express Camera Link Frame Grabber
PCIE-1121
Frame Grabber
Half-Size PCI Express Board Gen 2.0 x4Camera Link clock up to 85 MHzCamera Link Base/Medium/Full/80-BitSupports up to 4 independent camerasSupports PoCL and non-PoCL cameras with SafePowerImage sizes up to 268,435,456 x 16,777,216Independent I/O (trigger, encoder, strobe, etc) for each camera
-
Product
PCI 8x9 RF Coaxial Matrix Card 50Ω SMB
50-725A-511
Matrix Switch Module
The 50-725A is an 8x9 RF Matrix Module suitable for switching frequencies up to 500MHz. The 50-725A is available in either 50Ω or 75Ω versions with SMB coaxial connectors. It is intended for the easy construction of high performance bidirectional matrix switching systems.
-
Product
PCI Bit Synchronizer
LS-40-P
-
The Lumistar LS-40-P PCI Bit Synchronizer provides optimal reconstruction of a serial PCM data stream that has been corrupted by noise, phase jitter, amplitude modulation, or base line variations. The all-digital design assures a consistent product with high reliability and long-term stability. The LS-40-P PCI Bit Synchronizer consists of the LS-40-DB Bit Synchronizer Daughterboard shown below mounted on a PCI carrier board.
-
Product
2-CH PCI Express® PoCL Frame Grabber
PCIe-CPL64
Frame Grabber
PCIe-CPL64 is a PoCL (Power over Camera Link®) frame grabber that is based on the PCI Express® x4 interface, and supports two-channel Camera Link "base" configurations, multi-tap area and line scan cameras. The PCIe-CPL64 frame grabber strikes a perfect balance between performance and cost. It is capable of simultaneously image acquisition from two completely independent Camera Link base configuration cameras, and supports image transfers rates up to 512 MB/s.
-
Product
MIL-STD-1553 PCMCIA/PCCARD & PCI ExpressCard 54mm Cards
PCCD-1553 and ECD54-1553
Interface Card
Alta Data Technologies’ PCCD-1553 & ECD54-1553 interface modules are a multi-channel (1-2) 1553 card supported by the latest software technologies. The cards are based on the industry’s most advanced 32-bit 1553 FPGA protocol engine, AltaCore™, and by a feature-rich application programming interface, AltaAPI™, which is a multi-layer ANSI C and Windows .NET 2.0 (MSVS 2005 C++, C#, VB .NET) architecture. This hardware and software package provides increased system performance and reduces integration time.
-
Product
PCI 16x4 2Amp High Density Matrix Card
50-528-002
Matrix Switch Module
The 50-527, 50-528 and 50-529 are a range of PCI single pole matrix cards supporting either 64 or 128 crosspoints using electro-mechanical relays. They are capable of switching voltages up to 300VDC/250VAC and current up to 2A.
-
Product
PCI 2 Amp Multiplexer, Dual 16-Channel, 2-Pole
50-635A-006
Multiplexer Module
The 50-635A-006 is a dual 16-channel, 2-pole MUX and is part of a range of PCI Multiplexer cards available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
Passive XMC-to-PCI Express Adapter
5935
-
The Technobox, Inc. P/N 5935 is designed to adapt a single-wide XMC card to a 1X PCI Express slot. The 5934 supports P15 only and allows access to PN4 signal via the adapter's DIN connector. The A and C rows of a 96-pin DIN connector connect with the 64-pin user I/O connector (J4/P4) on the mezzanine card, permitting internal connection of rear I/O.
-
Product
PCI Multifunction I/O
626
-
6 versatile 24-bit counters for encoders/timers with interrupt generation Fail-safe Digital I/O E-stop Relay Battery backup of counters Four 14-bit D/A outputs, 20 Khz update rate Sixteen 16-bit differential A/D inputs, 15 kHz rate Watchdog timer may be used to reset PCI bus 48 bi-directional digital signals for solid state relay boards, 40 with edge detection and interrupts
-
Product
PCI 18 Channel Precision Resistor Card
50-297-001
Precision Resistor Module
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
12 Port PCI Express
PEX 8615
-
The ExpressLane™ PEX 8615 offers 12 PCI Express Gen 2 (5.0 GT/s) lanes, capable of configuring up to 12 flexible ports and fully conforms to the PCI Express Base Specification, rev 2.0. PEX 8615 architecture supports a high-performance DMA engine with four DMA channels and internal buffer space for internal descriptor support. Up to 256 descriptors are supported internally or alternatively descriptors can also exist in host memory.
-
Product
12-Bit, 4-Ch Isolated Analog Output Universal PCI Card
PCI-1720U
Analog Output Card
4 12-bit D/A output channelsMultiple output ranges2,500 VDC isolation between the outputs and the PCI busKeeps the output settings and values after system resetOne DB37 connector for easy wiringUniversal PCI and BoardID™ switch
-
Product
Fibre Channel Test & Simulation Interface for PCI
PCI-FC4
-
Avionics Interface Technologies
Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speeds - Comprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent AnalyzerSupports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
-
Product
10/30 MS/s, 12-Bit, 4-Ch Simultaneous Analog Input PCI Card
PCI-1714
PCI Card
4 single-ended analog input channels12-bit A/D converter, with up to 30 MHz sampling rateMultiple A/D triggering modesOnboard FIFO memory 32,768 samples4 A/D converters simultaneously samplingProgrammable gainProgrammable pacer/counterBoardID™ switchUniversal PCI Bus (supports 3.3 V or 5 V PCI bus signals)
-
Product
PCI Express Gen 3 Test Backplane
SKU-015-01-PCIe
-
PCI Express Backplane was designed to support a variety of modern PCI Express board’s production testing and debugging. The backplane expands the Host computer into four x16 PCI Express slots via 10 ft. CAT7 data and 10-pin flat Power control cables. PCI Express Backplane and UUTs (unit under test – add-in PCI Express board) are powered by a standard ATX power supply connected to the backplane via 24 and 8 pin power connectors located on the backplane.
-
Product
PMC to PCI Express Adapter w/ TSI384
6083
-
The Technobox, Inc 6083 4-lane and 8638 1-lane carrier card allows use of a PMC in a PCI Express edge card slot. The product features an IDT TSI384 bridge IC used in transparent mode with a PCI express primary side and a PCI/PCI-X secondary side.
-
Product
PCI Programmable Resistor Card 2-Channel 2.5 Ohm To 4.09k Ohm - SPST
50-294-123
Programmable Resistor Module
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Basic 3U VPX-to-PCI Express (PCIe/PCI-e) Adapter
8065
-
The Technobox, Inc. P/N 8065 is a 3U VPX-to-PCI Express (PCIe) adapter that provides a convenient and cost-effective means for developing 3U VPX boards in a personal computer environment. It can also be used for production testing of 3U VPX boards. The adapter is a half-length PCIe card with the VPX card under test mounted close to the PCIe edge fingers to minimize signal lengths. When seated in a PC motherboard, the VPX card primary side faces upward to allow convenient access to components.
-
Product
PCI Precision Resistor Card 6-Channel, 2.5Ω To 201kΩ
50-297-041
Programmable Resistor Module
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
4-Ch 1.25 GHz, 16-bit D/A with DUC, Extended Interpolation, Virtex-6 - 6U VPX
Model 57671
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Four 1.25 GHz 16-bit D/As- Four digital upconverters- Extended interpolation range from 2x to 1,048,576x- Programmable output levels- 250 MHz max. output bandwidth- 2 GB of DDR3 SDRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- Dual µSync clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
Product
Flexible x4 PCI Express to 4 MiniPCI Splitter
SKU-071-0X
-
Flexible x4 PCI Express to 4 MiniPCI Splitter was designed to expand your modern motherboard (ATX, mini ATX etc.) that doesn’t have a MiniPCI interface. It allows your to connect up to four 124-pin MiniPCI add-in boards to the motherboard ‘s standard PCI Express connector.Splitter includes 4 MiniPCI adapter boards, x4 PCI Express host board, and 4 flat PCI Express cables.
-
Product
Compact XMC-to-PCI Express (PCIe) Adapter
8241
-
Our Compact XMC-to-PCI Express (PCIe) Adapter 8X (Front-Panel I/O Only) (8241) permits use of a standard VITA 42.3 air-cooled XMC in the smallest possible edge finger PCIe form factor. The length of the adapter is the length of the XMC, while the height is a standard PCIe board, not the low-profile version.
-
Product
PCIe-5763, 16-Bit, 500 MS/s, 4-Channel PCI FlexRIO Digitizer Device
786165-01
FlexRio Digitizer
The PCIe-5763 is a PCI FlexRIO Digitizer Device that simultaneously samples four channels at 500 MS/s with 16 bits of resolution and features 225 MHz of analog input bandwidth. With over 73 dB of SNR, the PCIe-5763 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA. Available in AC and DC coupled variants, the PCIe-5763 is ideal for both time and frequency domain applications, including radar prototyping, LIDAR, communications, microscopy, OCT, event detection, and particle physics.
-
Product
PCI Express® Bus to 3U PXI Express™ Chassis Expansion Kit
PCIe-PXIe-8565
PXI Express Module
Includes PCIe-8560 peripheral card, PXIe-8565 3U system module, and ACL-EXPRESS cable in 1, 3, or 7 meter lengthsCompliant with PXI-5 PXI Express hardware specification Rev.1.0 and PCI Express Base Specifications Rev. 1.0a250 MB/s maximum system throughput
-
Product
PCI Express® Bus To 3U PXI Express™ Chassis Expansion Kit
ACL-EXPRESS-3
-
The PCIe-to-PXIe expansion kit includes one PCIe-8560, one PXIe- 8565, and one ACL-EXPRESS cable (3 meters).
-
Product
PCI & PXI Waveform Generators
-
Tabor’s PCI/PXI Arbitrary waveform generators are designed to enable a high level of integration, allowing it to implement its unique Arbitrary waveform generation technology in this platform.
-
Product
18-Port PCI Express
PEX 8733
-
The ExpressLane™ PEX 8733 is a 32-lane, 18-port, PCIe Gen 3 switch device developed on 40nm technology. PEX 8733 offers Multi-Host PCI Express switching capability that enables users to connect multiple hosts to their respective endpoints via scalable, high-bandwidth, non-blocking interconnection to a wide variety of applications including servers, storage, communications, and graphics platforms.
-
Product
PCI Strain Gauge Simulator Card, 2-Channel, 2k
50-265-302
Strain Gauge Simulator
These cards simulates the operation of a range of strain gauges making them ideal for testing strain gauge meters and a wide variety of industrial control systems. They provide a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
Product
PCI Very High Density Multiplexer, 49-Channel, 2-Pole
50-670C-021-49/2
Multiplexer Module
The 50-670C-021-49/2 is a 49-channel, 2-pole MUX and is part of a series of very high density multiplexer cards feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.The 50-670C shares exactly the same architecture as the established 40-670 range of PXI modules.
-
Product
2-port/4-port PCI Express 1GigE PoE Card with M12 X-
AX92325
-
Four M12 x-coded connectors with special design (to avoid occupying two slots) 2 or 4 independent Gigabit PoE ports, Supports 9.5KB Jumbo Frame and IEEE 1588, Compliant with IEEE802.3at to deliver 30W at 54 VDC per port, PCI Express x4 compliant
