PCI Diagnostic Cards
See Also: POST Cards
-
Product
PCI System Timer
SKU-051-01
-
The PCI System Timer uses a hardware clock to synchronize IP signals. This hardware-based solution provides accurate clock timing for Asterisk® open-source PBX software.The timer supports variable clock timing intervals. You can configure the clock interval during startup. Currently, the PCI System Timer supports clock interval ranging from 1ms to 64ms.
-
Product
6U Horizontal Card
733
-
VECTOR Electronics and Technology, Inc.
Chassis for horizontal card installation
-
Product
Isolated Digital I/O Card
mPCIe-IDIO-8
-
The mPCIe-IDIO-8 consists of a type F1 PCI Express Mini Card (mPCIe) interface board that connects to a Mobile-ITX-sized, DB-37M Isolation Module via an included 9” cable. That module is designed to be easily panel-mounted in any application environment. It uses the high speed PCI Express bus to transfer digital data to and from the card. The digital I/O is compatible with 8255 PPI chips making it easy to program.
-
Product
Multifunction Analog I/O Card
LPCI-AIO16A
-
Model LPCI-AIO16A provides 500k samples/second, with 16-bit resolution, for the board’s 16 single-ended or 8 differential analog input channels. Also included are two 12-bit analog outputs, 16 digital I/O lines and an 8254 with three 16-bit counter/timers. The board meets the MD2 Low Profile PCI Bus Specification and can be installed in any 3.3V or 5V PCI or PCI-X slot.
-
Product
PCI Express Cable Extender
SKU-016-XX
-
The PCI Express Cable Extender was designed to support the development and debugging of PCI Express boards. The PCI Express Cable Extender allows easy access from both sides of the PCI Express board that are plugged into the Extender. It has overcurrent protection and provides access to the PCI Express bus JTAG signals. By enabling access to the PCI Express bus JTAG signals, the PCI Express Cable Extender becomes a universal device that helps support the programming/loading of FPGA/CPLD during debugging and the verification PCI Express boards.
-
Product
Serial-to-Daq Card
Model 2307
-
* 2307 Board provides 32 digital I/O lines, 4 analog outputs, 6 analog inputs, 6 relay driver outputs and 4 temperature inputs.* Firmware supports ASCII command strings, Addressed commands for RS-485 networks and packet protocol. * Operates as a RS-232 as a RS-485 to Data Acquisition Board. * DE-9 connector has both RS-232 and RS-485 signals.* SCPI commands and IEEE 488.2 compatibility provide GPIB like operation over the serial link. * Runs on 5 Vdc power.
-
Product
Magnetic Stripe Card Reader
UTC-P02-A2E
-
RS232 optional. USB connection to UTC. Head life 1,000,000 times. Reading speed: 1-60ips. Card standard: ANSI, ISO, ABA.
-
Product
XMC-to-PCI Express Adapter
4822
-
The Technobox, Inc. P/N 4822 XMC-to-PCI Express Adapter permits the use of a single-wide XMC module in a 4x PCIe slot. PCI express lanes on the P15 XMC connector are routed to the male PCI express edge finger connector. The reserved future use, RFU, signals from P15 are available on one of the user connectors. The adapter also provides user access to all the signals on the XMC P16 connectors via two 64 pin headers UC1 and UC2.
-
Product
PCI Daughter Boards
DB-24SSR
-
The DB-24SSR/DB-24SSRDC includes 24 normally open, or form A, solid-state relays The board interface to filed logic signals, eliminating ground-loop problems and isolating the host computer from damaging voltages. The user can use the DB-24SSR/DB-24SSRDC to switch high voltage load, up to 240 VAC/50 VDC and up to 4 A. The relay is energized by applying a 5-voltage signal to the appropriate relay channel on the 50-pin header or 37-pin D-sub connector. Twenty-four enunciator LEDs, one for each relay, light when their associated relay is activated. Because there is a D-sub 37-pin connector on the board, the user may use it to interface to any TTL output board. In other words, the user may use it as a general purpose solid state relay output board.
-
Product
Super MUTT Head Portable, Remote Controlled Diagnostic Trailer Tester
#9005A
-
Innovative Products of America
The Super MUTT Head is a portable, remote controlled diagnostic trailer tester for inspecting lighting, ABS and air brake systems on commercial type trailers. Specially designed for service trucks and offsite inspections, the Super MUTT Head is powered by an (optional) internal 12v battery, or external power source such as a service truck battery, using the supplied external connector and requires shop air for air brake application.
-
Product
PCI Precision Resistor Card 18-Channel, 1Ω to 31.5Ω
50-297-010
-
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PCI Daughter Boards
DB-1825
-
Screw terminal board using 37 pin cable I/O ports for PCI-1202/1602/1802/822/826 series , (32 channel single-ended ,16 channel differential)Blank pads for break detection, Low-pass filter , current shut and voltage divider (manual soldering)Dimensions :170 mm x 114 mm
-
Product
Multi-Protocol Card
EXC-4000PCI
-
The EXC-4000PCI/xx card for the PCI bus supports up to forty ARINC-429 channels in any combination of transmit and/or receive. All of the channels feature error injection and detection.The receive channels allow for the storage of all selected labels with status and time tag information appended to each word, and also allow for filtering and multi-storage modes of data words.The transmit channels operate via a transmit ‘instruction stack’ which allows scheduling of data transmissions and reduces the need for host computer intervention.
-
Product
Circuit Module, Riser for ISMB, PCI to 1 PCI A101-1,RoHS
AIMB-RP10P-01A1E
-
- Connecting Interface: PCI x1- Expansion Slots: 1 PCI- 1U Riser Cards
-
Product
PCIe Card MX3 Copper Interface
OTP2 module no.183
-
PXI offers the optimal approach to validation and production testing. You can meet timing, synchronization, and throughput requirements across devices. PXI is a robust PC-based platform for measurement and automation systems, supported by software. PXI combines PCI electrical bus characteristics with CompactPCI's modular Eurocard packaging, and then adds special synchronization buses and important software functions.
-
Product
Multi-standard Cable/terrestrial Modulator For PCI
DTA-115
-
DekTec's PCI modulator for most QAM-, OFDM- and VSB-based modulation standards. The DTA-115 has a programmable output level with perfect signal quality.
-
Product
PCI Resistor Card 2-Channel 2 Ohm To 16.3k Ohm With SPDT
50-293-131
-
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Cfast Cards
-
CFast cards (CompactFast) combine the CompactFlash form factor with a SATA interface to deliver high-speed data transfer (up to 550+ MB/s) and superior endurance for professional 4K/6K cinema cameras and industrial applications.
-
Product
96-CH High-Driving DIO Card
PCI-7396
-
The PCI-7396 is 96-bit parallel digital input/output (DIO) cards designed for industrial applications. The PCI-7396 emulates four 8255 Programmable Peripheral Interface (PPI) chips. Each PPI offers three 8-bit DIO ports which can be accessed simultaneously. The total 12/6 ports can be configured as input or output independently.
-
Product
PCI High Density Pecision Resistor Card, 3-Channel, 4Ω To 1.51MΩ
50-298-150
-
The 50-298-150 is a high density programmable resistor card with 3 channels which can be set between 4Ω and 1.51MΩ with 0.125Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Universal Diagnostic System
BoardMaster External Case Solution
-
The ABI BoardMaster External Case universal diagnostic system is a uniquely versatile and easy-to-use test system. It offers the most comprehensive set of test instruments for fault-finding on almost any kind of PCB. With the full range of instruments and a variety of test methods guaranteeing the best possible fault coverage, the BoardMaster External Case provides the ultimate in diagnostic tools.
-
Product
CPCI Avionics Bus Card
-
Avionics Bus Card is high end ARM core based MILBUS Communication Board. It is suitable for high speed Data Acquisition, Simulation, ATE applications. This board have MIL1553B, ARINC429, CCDL, digital I/O interface, USB, RS232, Ethernet interface and external bus interface. Board is well suitable for special type data acquisition & processing application. Board is based CPCI architecture and can be used with CPCI or PXI backplane. Rear IO Board is used to interface all IO’s of the board from Rear Side.
-
Product
PCI Express Digital I/O Cards With Counters And COS Detection
PCIe-DIO-24DCS, PCIe-DIO-24DC, PCIe-DIO-24DS, and PCIe-DIO-24D,
-
This product is a x1 lane PCIe DIO board available in four models ranging from basic DIO to advanced COS detection and Counter/Timer capabilities. The card emulates an 8255 compatible chip, providing 24 DIO lines. The DIO lines are grouped into three 8-bit ports: A, B, and C. Each 8-bit port is configured via software to function as either inputs or outputs. Port C can be further broken into two 4-bit nybbles via software and configured as either inputs or outputs.
-
Product
FPGA Mezzanine Card
FMC126
-
The FMC126 is a quad-channel multi-mode A/D FMC, fully compliant with VITA 57.1 standards.The card provides four 10-bit ADC channels that enable simultaneous sampling of 4, 2, or 1 channel with a maximum sample rate of 1.25 GSPS (4-channel mode), 2.5 GSPS (2-channel mode), or 5.0 GSPS (1-channel mode).
-
Product
PCI Express card carrier, PCIe Gen 3 x8 connection
SA4-COUNTRY
-
The SA4-COUNTRY is a peripheral slot board for PICMG® CompactPCI® Serial systems and acts as carrier for low profile PCI Express® Card. The SA4-COUNTRY is provided with a PCI Express® x8 connector.
-
Product
FPGA Card
VP680
-
The VP680 is a high performance VITA 46 (VPX) standard compliant card with advanced digital signal processing capabilities. The design has been targeted for customer-programmable implementations of complex FPGA algorithms for digital signal processing (DSP) applications.
-
Product
Cantilever Probe Cards
Venture
-
Nidec SV Probe’s VentureTM line of cantilever probe cards represents the finest epoxy technology on the market and are perfect for logic testing. The Venture line includes an extensive array of cantilever cards, single to multi-die for a variety of test systems. Other capabilities include: • 3K Points • Pad Pitches as Tight as 35µm • Up to 32 DUTsContact your Nidec SV Probe sales representative to determine which VentureTM product is right for your testing application.
-
Product
VXI PCI Express Crate Controller
V124
-
The V124 is a VXI bus master crate controller, usable as a crate slot 0 arbiter or as a secondary controller. Each PCI Express cable driver board, in a PC backplane, can drive one to four V124s over standard, flexible PCI Express cable assemblies up to 7 meters long.
-
Product
Multi-Protocol Serial Card
PCM485
-
The PCM485 is a multi-protocol serial card that supports RS-422 or RS-485 communications in a single 5V PCMCIA Type II card. The PCM485 uses a crystal controlled oscillator which permits precise selection of baud rates from 50 to 115,200.
-
Product
Production Parametric Probe Card
VC20TM Fab
-
*Maximum channel count: 48*Tester platforms: Keysight 4062, 4072, 4080, Keithley S600, S530, Rack and Stack configurations.*Minimum Pad Size: 30ux30u (tunable scrub)*Contact Resistance: less than 1 ohm*Temperature range: -65C to 200C*Leakage: Less than 5 femto Amps per volt. If you require faster settling time*Repairable*Lifetime Performance: Production customers are experiencing 10M+ million touchdowns on Aluminum and Copper pads. Few to no rebuilds due to pobe wear
