Pulse Amplifiers
increase amplitude while keeping waveform. Also known as: Pulsed Amplifiers
-
Product
HyMPulse Pulsed Field Magnetometer
-
Metis Instruments & Equipment NV
Geometry independent M-measurement (patent pending): One probe fits all, no pole shoes per magnet geometry. Measure the actual magnet instead of a prepared standard size sample. Measurement of industrial shapes like segments, cylinders, bricks,... with one probe
-
Product
Pulsed IV
AURIGA 4850
-
Pulsed IV (current-voltage) measurements have emerged as the preferred method of capturing current-voltage characteristics of active devices such as field effect (FETs) and bipolar junction (BJTs) transistors.
-
Product
Solid State Power Amplifiers
SSPAs
-
Communications & Power Industries
- Ruggedized for use in pulsed airborne, naval and ground radar- Found in weather forecasting Doppler radar systems- Utilized world-wide in air traffic control and precision approach radar systems
-
Product
Conventional Panel-mounted Type Power Amplifier Control Unit
PAT01
-
PAT01 is a power amplifier control unit that controls timing output and reference signal test source for power amplifier.
-
Product
Ultra-Low Phase Noise Amplifiers
-
When phase noise is critical, turn to Mercury’s line of low phase noise amplifiers. Taking full advantage of the industry’s best device technology, these parts are designed to meet the toughest requirements. Through Mercury System’s advanced production capabilities, phase noise can be accurately measured—even during environmental tests, such as vibration.
-
Product
Basic Quad K-Type Analog Thermocouple Amplifier
SEN-30103-K0
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
Benchtop Amplifiers
-
Benchtop, broadband driver amplifiers are designed and manufactured by utilizing the most advanced PHEMT or MMIC devices, thin film technologies, and an improved DC power supply to deliver a high output power and a superior gain flatness and low noise performance. The standard offering focuses on general purpose applications and covers the frequency range of 1 to 110 GHz. However, custom designs are also offered to meet any user’s specific needs.
-
Product
Premium Headphone Amplifier
A 20
-
A new standard for headphone amplifiers that brings out the potential of Tesla drivers. Premium headphone amplifier that inherits the design of A 1.
-
Product
QuickLink Solder-In Starter Pack for use with Dx10 Amplifier
Dx10-QL-3SI
-
- Choice of 4 GHz or 6 GHz bandwidth models- Up to 5 Vpk-pk dynamic range with low noise- ±3 V offset range- Low loading and high impedance for minimal signal disturbance- Ideal for DDR2, DDR3, LPDDR2- Deluxe soft carrying case- Innovative QuickLink architecture- Wide variety of tips and leads-- Solder-In Lead-- Optional Positioner (Browser) Tip-- Quick Connect Lead-- Square Pin Lead-- HiTemp Solder-In Lead
-
Product
C-Band Separate Dispersion Compensation Raman Fiber Amplifier
DRA5228/F
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Raman Fiber Amplifier (RFA) utilizes the optic gain in the Stimulated Raman Scattering (SRS) in the optical fiber and realizes the amplification of the signal optic. FRA, with very low equivalent noise and a wide gain scope, can further widen the gain bandwidth by adopting multi-wavelength optical bump, which represents the development direction of the new optical fiber amplifier.
-
Product
Flex Power Right Angle Non Shut-Off Pulse Tools
-
The non shut-off right angle pulse tools are ideal selection when the operator needs to control the fastening process. It offers access for hard-to-reach fasteners in tight spaces. The drive on a right-angle tool is mounted at a 90-degree angle to the tool body. Designed for safe, reaction free operation for various industrial assembly applications. The FlexPower Pulse Tools provide operators with an industry leading power-to-weight ratio, allowing for a smaller tool selection for greater torques giving operators a lighter tool with more torque capability. Ergonomically safer than harmful hammering and vibration of impact wrenches. Built for durability with a superior O-ring design and specially designed pulse fluid FlexPower extends life between regular oil changes and provides more torque stability. Low noise decibels, minimal vibration and low torque reaction. It is important to understand your joint application before a selecting a pulse tool.
-
Product
Basic Quad J-Type Analog Thermocouple Amplifier
SEN-30103-J1
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
2- to 8-Channel Anti-Alias Low-Pass Filter and Instrumentation Amplifier Card
AAF-3
-
The AAF-3 is a 2- to 8-channel anti-alias low-pass filter and instrumentation amplifier ISA bus plug-in board for front-end signal conditioning in PC-based data acquisition systems.
-
-
Product
Low Phase Noise Amplifiers
-
Low Phase Noise amplifiers are critical for many applications requiring high signal integrity. This is especially relevant in instrumentation, defense, and telecommunication applications where low phase noise amplifiers are becoming increasingly important as the oscillators improve. Phase noise is described as the close-in noise to the carrier that can often appear as jitter on a clock signal. Analog Devices offers a large portfolio of low phase noise amplifiers to meet a variety of requirements in the LO network, receiver, as well as in the transmitter. Our portfolio supports a wide range of power levels and frequencies to provide the right solution for the given application.
-
Product
Charge Integrator Amplifiers
AD8488
-
Analog Devices’ charge integrator amplifiers convert the charge acquired by X-ray or photodiode detectors to a voltage. The channels are composed of CMOS transistors, using typical high input impedance CMOS gates. The integrators generate charge dependent voltages using a range of selectable capacitance values that accommodate a broad range of input charge values. The integrators are followed by single-ended input to differential output voltage amplifiers where offset and low frequency noise voltages are subtracted from the input voltages.
-
Product
High-Power CW Amplifiers
-
Our family of solid-state power amplifiers (SSPAs) utilizes proprietary technology and a proven building block approach that enables rapid customization to specific requirements. The world-class design team understands the tradeoffs between GaAs versus GaN and FET versus MMIC to quickly achieve the right design for the right problem. Whether you need a connectorized compact GaN SSPA or an integrated SSPA assembly, we have the technical know-how to deliver on-time and on-budget.
-
Product
Semiconductor Power Amplifiers : Solid State Power Amplifiers (SSPA) For Indoor (rack-mount) And Outdoor (hub-mount) Settings
-
Insight Product Company is proud to offer state-of-the-art semiconductor (solid state) power amplifiers that are compact, rugged, and deliver immense power, and expectional frequency stability and minimal phase noise. These solid state power amplifiers are ideal for indoor, rack-mount, or outdoor, hub-mount, applications. We offer S-band, C-band, X-band, and Ku-band amplifiers, with output power of upto 1,000 Watts (varies based on frequency band).
-
Product
Short Pulse High-Frequency Laser Marker
LP-RV SERIES
-
Panasonic Industrial Devices Sales Company of America
The LP-RV Series FAYb Laser Marker features:- Short Pulse 20W Fiber Laser Offers Excellent Mark Contrast On Difficult To Mark Plastics And Various Other Materials- Optional EtherNET/IP Or ProfiNET Interface Adaptor Card- Modular Laser Oscillator System Makes Servicing In The Field Possible - Direct Connection To Panasonic PV230 Vision System For Mark Verification, Auto-Targeting, And Other Machine Vision Functions- Compact IP64-Rated Marking Head For Use In Harsh Environments- Compliant With FDA Regulations, GB Standard, KC Mark, Machinery Directive (Declaration of Incorporation), EMC Directive, RoHS Directive
-
Product
High Voltage Amplifier
HA-800
-
*800Vp-p(±400V DC) *70mAp-p(±35mA DC) *Bandwidth: ≦200KHz(400Vp-p) *Slew Rate: 200V/us *Gain(AMPL): 0~180(10 Turn VR) *DC Offset: ≦0~±400V (10 Turn VR + SW) *Output Resistor: 100*Ω
-
Product
Panel-mounted Voltage Power Amplifier
PAV120Bi
-
PAV120Bi is specially designed for R&D of power system simulation. It is adapt to various capacitive and inductive load. It is with 6 channels voltage outputs, each channel with 120V/60VA maximum output.
-
Product
Microwave Power Amplifier 1/2 Watt 100 MHz to 20 GHz
GT-1020A
-
The Spanawave/Giga-tronics GT-1020A Microwave Power Amplifier incorporates broadband MMIC-based architecture. These state-of-the-art amplifiers are based on solid-state parallel MMIC design with exceptionally wide bandwidth and high power. The unique circuit topology is highly reliable, with performance that excels where extremes of bandwidth and power are demanded.
-
Product
Ku Band Gain Control Amplifier
-
Expanding Teledyne RF & Microwave's existing line of high frequency amplifiers, microwave gain controllable amplifiers are designed and biased for critical performance applications. One example covers 10-13 GHz, offers 45 dB unattenuated small signal gain with 15 dB attenuation range. Typical gain flatness is ±0.5 dB, +35 dBm third order intercept point, +22 dBm minimum 1-dB gain compression, and 3.5 dB unattenuated noise figure 4.5 dB at full attenuation. This is only one of a series of microwave controllable amplifiers currently in production.
-
Product
Pulse Magnetic Field Generator
SKS-0902
-
Shanghai Sanki Electronic Industries Co., Ltd.
The technical parameters of the pulsed magnetic field generator SKS-0902 fully comply with the new standards of IEC61000-4-9 and GB/T17626.9; the pulse current output of up to 2000A can meet the needs of different user groups; it adopts a self-developed CNC high-voltage power supply, High precision, high stability, long service life; using self-developed high-voltage electronic switch as the main switch, high stability, smooth output waveform; achieving 0°~359° synchronous phase triggering.
-
Product
DC Pulse Current Capacitor
-
Both series can be customized as Low Voltage High Capacitance High Current Capacitors.We can customize Snubber Capacitor as Box type and support other parameters.For 250Vac~900Vac / 400Vdc~1,350Vdc and with higher Current requirement, please refer to our AC/DC Power Capacitors.Different applications can have very different capacitor electrical and mechanical profile requirements.Please feel free to send your application details for a suggestion and quotation.
-
Product
Solid State Power Amplifier Module (SSPA)
-
Macom Technology Solutions Holdings Inc.
MACOM’s Solid State Power Amplifier (SSPA) and waveguide module product portfolio leverages our world class MMIC technology and system design expertise for high performance Industrial, Aerospace, Defense, and Communications applications. Our SSPA modules feature up to 16 power-combined MMICs in a single module and we can power-combine multiple modules up to 100GHz featuring either coaxial or waveguide interfaces.
-
Product
RF Medium / High Power Amplifier
-
Corech Microwave’s RF medium/high Power Amplifier(PA) frequency ranges from 0.1 to 52 GHz, up to 100W high power output (CW or Pulse). Narrow-band & wide-band ready modules are available SMA, 2.92mm, 2.4mm, WR28, WR24 and PIN connector options are available.
-
Product
Wireless Pulse Input Transmitter Module
T24-PA
-
The T24-PA transmitter module collects and processes pulse related measurements, such as speed of rotation, proximity, flow and count, forming part of the T24 modular telemetry system. The data transmitted by the T24-PA can be received by multiple T24 receivers that include displays, handheld readers, analogue outputs, relay modules and computer interfaces.
-
Product
High-Speed System Sync and Distribution Amplifier - SOSA Aligned 3U VPX
Model 5503
-
- Supports Xilinx® Zynq® UltraScale+™ RFSoC FPGAs- Synchronizes up to 32 channels across four Quartz boards- Synchronizes sampling and data acquisition for multichannel systems- Provides single sample accurate synchronization between multiple channels and multiple boards- Synchronizes gating and triggering functions- Optional VITA 67.3D optical interface for backplane gigabit serial communication
-
