Pulse Amplifiers
increase amplitude while keeping waveform. Also known as: Pulsed Amplifiers
-
Product
Load Cell Amplifier
-
Xiamen Elane Electronics Company, Ltd
: 0-50 degrees. Humidity: 30 to 80 percent, non-condensing.Power Supply Requirements:Power Supply voltage: 9 volts DC.Operating current: 5mA, plus bridge current.Bridge Input:Excitation voltage: 5 volts.Bridge Type: Full Wheatstone Bridge.Voltage Output Range: From 0 volts to 4.3 volts.
-
Product
IRIG Amplitude Modulated Time Code Distribution Amplifier
1205A / 1205A-MC
-
Precise Time and Frequency, Inc.
The ptf 1205A is a 12-channel IRIG amplitude modulated time code distribution amplifier housed in a 1U high, 19″ rack package. The ptf 1205A uses an RF design combining the latest technology in low noise components to minimize input/output delays which are of the order of nano seconds.The unit uses two stages of input signal buffering to distribute the input signal to 12 separate outputs, and insure maximum isolation between individual output signals.
-
Product
PXIe-4135, PXIe, ±200 V, ±1 A DC, ±3 A Pulsed, Up to 40 W DC, 10 fA Precision System PXI Source Measure Unit
783762-02
-
PXIe, ±200 V, ±1 A DC, ±3 A Pulsed, Up to 40 W DC, 10 fA Precision System PXI Source Measure Unit - The PXIe-4135 is a high-precision, system source measure unit (SMU). It features 4-quadrant operation and sources up to 40 W of DC power and can pulse up to 500 W. Analog-to-digital converter technology and native triaxial connectors help you perform high-precision measurements with a current resolution of 10 fA or high-speed acquisitions up to 1.8 MS/s. The module also can maximize stability and measurement accuracy with SourceAdapt technology, which you can use to tune the transient response to match the characteristics of any load. The PXIe-4135 is ideal for a broad range of applications including manufacturing test, board-level test, and lab characterization with devices such as ICs, power management ICs (PMICs), and RFICs and discrete devices including LEDs and optical transceivers.
-
Product
Portable Power Amplifier
PAV120Bip
-
PAV120Bip（6*120V） is the portable type power amplifier which is specially designed for R&D of power system simulation. It is with linear type amplifier design so that it could be adapted to simulation experiment which may include various capacitive and inductive load.
-
Product
GPS Filter Amplifiers
-
Mercury Systems’ family of GPS filters/amplifiers is the right choice for your high reliability GPS receiver. Whether your application is ground, airborne, missile or launch/reentry vehicle, you can trust the technology behind these advanced products. Custom designs including multiple outputs and integrated receiver protection limiters are also available.
-
Product
1×6 Video Distribution Amplifier
VDA206 S-Video
-
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.
-
Product
Motion Control Terminal Board For Panasonic MINAS A4 Servo Amplifiers
DIN-814-A40
-
- Panasonic MINAS A4 super servo- Dimensions: 123 mm x 107 mm x 44 mm (WxLxH)- Available for PCI-8174, PCI-8164, PCI-8154, PCI-8158 and PCI-8134
-
Product
3-Ch Sensor Amplifier
PS-1300
-
The PS-1300 3-Ch Sensor Amplifier is designed to be compact and light weight, and able to be used in combination with a tri-axial accelerometer. Each channel can also be used independently and connected with a single axis accelerometer. The PS-1300 has built-in integration function and enables to optimize the input signal to vibration data analysis devices connected.
-
Product
40mA One-Channel Amplifiers
-
Piezo amplifiers/controllers are designed for high precision low to mid-speed positioning of low-voltage piezo actuators. These amplifiers are tuned for extremely high output stability and extremely low signal noise at the output. A low amplifier signal-to-noise ratio is very important because it determines the total resolution of the actuator. The nearly unlimited resolution of piezo-electric actuators using these amplifiers results in ultra-precise movement.
-
-
Product
Erbium Doped Fiber Amplifier
EDFA
-
Optoplex designed and produced high power single-mode and polarization-maintaining EDFA, which met MSA compatible requirements. C-band MSA EDFA Module with +23 dBm Output Power is Optoplex standard product. Optoplex designed Pre-EDFA provides more than 35dB gain with -40dBm input power. The Double-Cladding pumped EDFA produces 2W output power.
-
Product
RF Amplifiers Bias Controllers
-
RF amplifier bias controllers generate a regulated drain voltage and actively adjusts the gate voltage of an external amplifier to achieve constant bias current. It can be used to bias any enhancement and depletion type amplifier operating in Class-A regime with drain voltages (VDRAIN) as specified. These devices achieve excellent bias stability over supply, temperature and process variations, and eliminates the required calibration procedures used to prevent RF performance degradation due to such variations.
-
Product
Thermocouple Interface Amplifiers
-
Analog Devices offers specialized precision thermocouple interface amplifiers that provide a simple and effective solution for measuring thermocouple temperatures. With features such as integrated cold junction compensation and a high gain precision instrumentation amplifier, these thermocouple amplifiers provide a complete signal conditioning system in one IC package. ADI’s thermocouple amplifiers are suitable for use in diverse environments to measure a wide range of temperatures. These products will save you in cost, space, and unnecessary circuit design across a broad range of applications and industries.
-
Product
Pulse Data Logger
Pulse101A
-
The Pulse101A is one of MadgeTech's best selling data loggers. It is part of an original series of low cost, state-of-the-art data logging devices. MadgeTech has taken the lead in offering the most advanced, low cost, battery powered data loggers in the world today.
-
Product
Solid-State RF amplifier module for High Power Testing
-
Exodus Advanced Communications
Exodus introduces the AMP1071 - a Solid-State RF amplifier module covering the entire ultra-wide 2.0-20.0GHz frequency range instantaneously at 20W CW minimum. Using State of the Art GaN devices, the AMP1071 operates from a 32VDC source at less than 10A consumption. This module is suitable for use with all single channel modulation standards and applications requiring high power and ultra-wide band coverage. It has built-in protection circuits, high reliability and ruggedness. Typical applications include High Power Testing, EMI/RFI, EW and Communications and Jamming.
-
Product
High-Voltage Amplifiers - to 1000 Volts peak-to-peak
-
These amplifiers provide high amplitudes and bandwidths, and are well suited for use as booster amplifiers for lower-voltage arbitrary waveform generators.
-
Product
MOSFETs For High Frequency Amplifier
-
The MOSFETs shown below are best suited for amplification of high-frequency signals.
-
Product
GN Range Broadband Power Amplifiers 100 KHZ - 200 MHZ
GN Series
-
Class A solid stateBroadband (instantaneous single band): 100 kHz 200 MHzTypical output power : 500 W CWLinear output power (1 dB compression) guaranted with harmonics <-20dBc:P1dB > 450 W and H < -20 dBc up to 100 MHz andP1dB > 180 W and H < -20 dBc from 100 MHz to 200Air cooling: self contained fansCan operate in full mismatch conditions without damageReliable, efficient and robust19" Rack3 years standard warranty
-
Product
Power Amplifier
2734
-
The 2734 is a compact class D power amplifier, intended for acoustical measurements in the field or laboratory. All controls and connectors are placed on the front panel, enabling you to set up the 2734 very quickly, and to operate it in horizontal or vertical position. The 2734 is built into a robust flight case making it safe and easy to carry along.
-
Product
Ultra Low Level DC Voltage Amplifiers
-
The EM A10 is a low level amplifier module for sensitive measurements, data collection and systems, where signals below 1 nanovolt may be measured. It is ideal for the input unit for precision voltage measuring systems, requiring voltage sensitivity for measuring low noise and low impedance sources. The noise level of the A10 is equivalent to a perfect resistor of about 20 ohms. When used with a digital voltmeter, steady one nanovolt digits may be displayed, with a response time constant of less than a second. The input voltage stability of the A10 is very high, with the drift around a nanovolt per degree C. The input connectors are made from pure copper. The input impedance is very high, and is time dependent, determined by the loop gain.
-
Product
Reference DAC, Pre And Headphone Amplifier
CALLIA
-
Designed and manufactured in the United Kingdom, CALLIA embodies the Prism Sound uncompromising approach to audio resulting in the most accurate and detailed DAC available.
-
Product
100-Amp Current Calibrator And AC/DC Transconductance Amplifier
2555A
-
World’s Leading Precision 100-Amp AC/DC Current Standard - For 30 years Valhalla Scientific’s design has proven rock-solid reliability in metrology labs worldwide. The 2555A is a calibration powerhouse with wide-ranging applications and unsurpassed quality.
-
Product
RF High Power Amplifier Modules
-
Analog Devices MMIC-based GaN and GaAs power amplifiers cover the low hundred MHz frequency range up through and including components in the Ka-band (29 GHz to 31 GHz). Our portfolio also includes GaN-based power amplifier modules with output power exceeding 8 kW. Designed for excellent linearity at high output power, our power amplifiers maintain good heat dissipation and high reliability at elevated temperatures for the wide variety of test, radar, and aerospace and defense applications that they are used in.
-
Product
4/8 Channel 1.0 ~ 30.0 Gb/s Pulse Pattern Generator and Error Detector
CA9808C
-
The UC INSTRUEMNTS CA9808C 4/8 Channel 1.0 ~ 30.0 Gb/s pulse pattern generator and error detector is a high performance, flexible and cost effective four channel Pulse Pattern Generator and Error Detector that can operate from 1.0 Gb/s to 30.0 Gb/s each Channel. 4/8 channel 30.0 Gb/s make it total up to over more than 120/240 Gb/s testing capacity. It is also a standalone Bit Error Rate test solution that incorporates an internal full rate clock synthesizer.
-
Product
DSP Dual Phase Lock-In Amplifier
SR850
-
Stanford Research Systems, Inc.
The SR850 is a digital lock-in amplifier based on an innovative DSP (Digital Signal Processing) architecture. The SR850 boasts a number of significant performance advantages over traditional lock-in amplifiers?higher dynamic reserve, lower drift, lower distortion, and dramatically higher phase resolution.
-
Product
hpower High Power Amplifiers
-
For hpower high-power actuators, high-power amplifiers are required. Together these hpower actuators and amplifier systems deliver exceptionally fast response times, superior dynamics, high force generation, and nanometer precision.
-
Product
SW Range Broadband Power Amplifiers 0.8 GHZ - 4 GHZ
SW Series
-
Class A solid stateBroadband (instantaneous single band): 0.8 GHz 4 GHzTypical output power : 18 W CWLinear output power (1 dB compression) guaranted with harmonics <-20dBc:P1dB > 13 W and H < -20 dBc up to 2.5 GHz andP1dB > 12 W and H < -20 dBc from 2.5 GHz to 4 GHzAir cooling: self contained fansCan operate in full mismatch conditions without damageReliable, efficient and robust19" Rack3 years standard warranty
-
-
Product
High Voltage Linear Amplifier
A800X
-
This unit is a version of A800 amplifier equipped with two inputs, DC-offset and output atenuation. Input A is a normal non-inverting one. Using this input alone makes A800X functionally identical with A800 amplifier.Input B can act as a inverting or non-inverting depending on the position of the corresponding switch.
-
Product
UX Range Broadband Power Amplifiers 2 GHZ - 6 GHZ
UX Series
-
Class A solid stateBroadband (instantaneous single band): 2 GHz 6 GHzTypical output power : 15 W CWLinear output power (1 dB compression) guaranted with harmonics <-20dBc:P1dB > 12 W and H < -20 dBc up to 4 GHz andP1dB > 11 W and H < -20 dBc from 4 GHz to 6 GHzAir cooling: self contained fansCan operate in full mismatch conditions without damageUpgradable to UX 30 possible (4U)Reliable, efficient and robust19" Rack3 years standard warranty
