Stepping Motor
A device that translates electrical pulses into precise mechanical movement. The output shaft may deliver rotary or linear motion. (www.seanet.com)
See Also: Electric Motor, Servomotor
-
Product
Motor Test for Stepping Motors
-
*Stable measurement: Since it uses Prony braking, this model provides stable measurement unaffected by moments of inertia and no coupling loss. In addition, the resulting measurements allow data correlation via the traditional double-balance method.*Precision measurement method: This model’s judgment of synchronization loss achieves high stability using algorithms developed by Sugawara Laboratories. Measurement mode can be chosen based on step angle. For pull-in torque, startup can be measured consistently from the holding state. Allows measurement at 1-Hz resolution.*Broad measurement range: This model offers a range of seven available measurement heads, from 0.5 N to 50 N, allowing use for high-precision measurements. Through selection and use of pulleys, this model can also be used to measure small motors of 0.5 mN·m or less or 500 mN·m motors. Pulley diameters and other settings are easily configured using a personal computer running Windows®. Note: Any of the seven available heads may be attached to a single measurement component.*High-visibility measurement data: Motor characteristics are easily ascertained on automatically plotted performance graphs. Measurement data can be overlaid up to four times. In addition, the cursor can be used to read accurate values from measurement points. Hard copies of data displayed on-screen can be printed from a personal computer.*Can be controlled using standard personal computers: Allows control of measurement operations and display and storage of data from a standard personal computer running Windows®. Data is stored in CSV-format files for compatibility with other software applications.
-
Product
Rotational Viscometer
DRK8S
-
Shandong Drick Instruments Co., Ltd.
DRK8S rotational viscometer is an upgraded product of our company's rotational viscometer. The instrument adopts advanced mechanical design technology, manufacturing technology and microcomputer control technology, and the data collection is accurate; the high-division drive stepping motor rotates smoothly and accurately.
-
Product
Rotational Viscometer
NDJ-5S
-
Shandong Drick Instruments Co., Ltd.
NDJ-5S rotational viscometer is an upgraded product of our company's rotational viscometer. The instrument adopts advanced mechanical design technology, manufacturing technology and microcomputer control technology, and the data acquisition is accurate; the high-division drive stepping motor rotates smoothly and accurately.
-
Product
Clippers
-
The device consists of a sturdy frame with step motor drive, which moves the water box with the Scherbüchsenunterteil. For the measurement of shear force, shear path and settlement electronic transducers are provided. The device control with measurement data acquisition takes place via PC with software PROPRESS.
-
Product
Three-phase Electricity Meters
-
Three-phase static electricity meters AMT B1x-S(D)xxTE are determined for single-rate or double-rate active energy measurement in direct and indirect connection, displaying results on mechanical register with stepping motor. In the case of CT (current transformer) operated meters (x/5A) it is necessary value of register to multiply by the current transformer ratio.
-
Product
4-Axis EtherCAT Motion SubDevice
AMAX-3245
-
Max. 5 MHz, 4-axis pulse outputEncoder input is 10 MHz for 4xAB mode, 2.5 MHz for CW/CCW modeBoardID is switchableEasily visible LED indicators on board to do diagnosisDirect wire to servo drive to save terminal board space while installationHorizontal installation for for servo or stepping motor driverSuitable for DIN-rail mountingProgrammable interruptMemory buffer (10K points) for trajectory planning which is designed in DSP4-axis position compare triggering up to 100 KHz, and memory buffer is up to 100 K pointsPosition latchSupports gantry mode by semi-closed loop pulse train controlLTC-dedicated input channels & SVON/CMP/RST/ERC-dedicated Output channels are switchable for general input and output purposes
-
Product
Shield
Arduino Motor Shield Rev3
-
The Arduino Motor Shield is based on the L298 (datasheet), which is a dual full-bridge driver designed to drive inductive loads such as relays, solenoids, DC and stepping motors. It lets you drive two DC motors with your Arduino board, controlling the speed and direction of each one independently. You can also measure the motor current absorption of each motor, among other features. The shield is TinkerKit compatible, which means you can quickly create projects by plugging TinkerKit modules to the board.
-
Product
Multi-Axis Motion Controllers
DMC-1800
-
The DMC-1800 for the PCI bus is a member of the Optima Series, Galil's full-featured multi-axis motion controllers. Designed to fit in a single PCI slot of a PC, the DMC-1800 controllers accommodate 1- through 8-axis formats and allow control of step or servo motors on any combination of axes.
-
Product
4-Axis EtherCAT Motion Module With CiA402 Device Profile
AMAX-3245C
-
Max. 5 MHz, 4-axis pulse outputEncoder input is 10 MHz for 4xAB mode, 2.5 MHz for CW/CCW modeBoardID is switchableEasily visible LED indicators on board to do diagnosisDirect wire to servo drive to save terminal board space while installationHorizontal installation for for servo or stepping motor driverEtherCAT CiA402 device profile CSP, HMSupports COE/FOE, PDO/SDOGeneral purpose I/O: 4DI/4DO
-
Product
ISA Optima Motion Controllers, 1-8 axes
DMC-1700
-
The DMC-1700 for the ISA bus is a member of the Optima Series, Galil's full-featured multi-axis motion controllers. Designed to fit in a single ISA slot of a PC, the DMC-1700 controllers accommodate 1- through 8-axis formats and allow control of step or servo motors on any combination of axes. Any mode of motion can be programmed including linear and circular interpolation, contouring, electronic gearing and ecam.
-
Product
Spectrographs & Monochromators
-
Manual micrometer adjustable slits for precision control of incoming light. Motorized Slit and fixed slit is optional. More than 100 gratings for the best spectral range, throughput and dispersion to meet your applicationDSP controlled stepping motor scanning system provides superior precision and repeatability of wavelength positioningOptional internal shutter or six-position filter wheel for experiments requiring background removal or signal attenuationInstallation and set-up through USB 2.0 computer interfaces Stand-alone Omni Series monochromator control software for basic scanning and calibration. Also includes utilities for grating updates and communications Active X control support Visual Basic, C++ and Delphi drivers allow users to design their own acquisition programsZolixScan data acquisition software provides a simple user interface for easy data acquisition and experimental set-up
-
Product
Single-phase Electricity Meters
-
Single-phase static electricity meters AMS B1x-SAx are determined for direct and indirect measurement of active energy displaying value on mechanical register with stepping motor. In the case of CT (current transformer) operated meters (x/5A) it is necessary value of register to multiply by the current transformer ratio.
-
Product
Micropositioner
XYZ 500 MIMT
-
Quarter Research and Development
Submicron manipulator and translation stage. The XYZ-500-MIMT Micropositioner is intended for precise probing and instrumentation for industrial, medical, biological, semiconductor, and general scientific applications. It provides 3-axis motion with .500" movement on each axis. Motion is controlled by three precision stepping motors attached to precision gear heads 64:1 (standard), that drive a 100 threads per inch screw (standard).
-
Product
SPL-03C-090 Step Probe
SPL-03C-090
-
Current Rating (Amps): 6Average Probe Resistance (mOhm): 50Test Center (mil): 125Test Center (mm): 3.18Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 127Recommended Travel (mm): 3.22Mechanical Life (no of cyles): 1,000,000Overall Length (mil): 1,530Overall Length (mm): 38.86Rec. Mounting Hole Size (mil): 95Rec. Mounting Hole Size (mm): 2.40Rec. Mounting Hole Remark: 94 to 96 mil / 2.39 to 2.44 mmRecommended Wire Gauge: 22-26 AWGRecommended Drill Size: #41 or 2.40 mm
-
Product
STP-25 Replaceable Step Probe
STP-25
-
Current Rating (Amps): 5Average DC Resistance lower than (mOhm): 35Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 135Full Travel (mm): 3.43Full Travel Remark: Varies with tip (min. 135 mil / 3,43 mm)Recommended Travel (mil): 120Recommended Travel (mm): 3.05Overall Length (mil): 1300Overall Length (mm): 33.02
-
Product
SPL-03C-153 Step Probe
SPL-03C-153
-
Current Rating (Amps): 6Average DC Resistance lower than (mOhm): 50Test Center (mil): 125Full Travel (mil): 200Full Travel (mm): 5.08Recommended Travel (mil): 127Recommended Travel (mm): 3.23Overall Length (mil): 1,530Overall Length (mm): 38.86Rec. Mounting Hole Size (mil): 95Rec. Mounting Hole Size (mm): 2.40Rec. Mounting Hole Remark: 94 to 96 mil / 2.39 to 2.44 mmRecommended Wire Gauge: 22-26 AWGRecommended Drill Size: #41 or 2.40 mm
-
Product
Threaded Step Probes
-
Pin position sensing - adjustable height - custom designs - anti-jump solution.
-
Product
Step Probes
-
*Precisely controlled probe travel*Step tip geometry*Replaceable and non-replaceable versions*Plating options available
-
Product
SPL-03C-114 Step Probe
SPL-03C-114
-
Current Rating (Amps): 6Average DC Resistance lower than (mOhm): 50Test Center (mil): 125Full Travel (mil): 170Full Travel (mm): 4.32Recommended Travel (mil): 127Recommended Travel (mm): 3.23Overall Length (mil): 1,530Overall Length (mm): 38.86Rec. Mounting Hole Size (mil): 95Rec. Mounting Hole Size (mm): 2.40Rec. Mounting Hole Remark: 94 to 96 mil / 2.39 to 2.44 mmRecommended Wire Gauge: 22-26 AWGRecommended Drill Size: #41 or 2.40 mm
-
Product
STP-1 Replaceable Step Probe
STP-1
-
Current Rating (Amps): 3Average DC Resistance lower than (mOhm): 35Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 135Full Travel (mm): 3.43Full Travel Remark: Varies with tip (min. 135 mil / 3,43 mm)Recommended Travel (mil): 120Recommended Travel (mm): 3.05Overall Length (mil): 1300Overall Length (mm): 33.03
-
Product
Motionnet Motion Control Modules
-
Motionnet comprises of a high-speed serial communication system that involves Master card and Slave modules. ICP DAS USA has two categories of Slave devices: Digital I/O, and Motion Control. Users' actuators/sensors can be easily connected with our Motionnet devices. Motion control modules work together with either a Servo or Stepping motor. Motionnet communication between a Master and the Slaves devices is based on RS-485 technology (Multi-drop, Half-duplex). This technology provides the advantage of simplifying connectivity of devices between remote distances while still offering high speed. Data transfer for the I/O modules is cyclical and time deterministic, so this mean that Motionnet devices can be used for other numerous industrial automation applications.
-
Product
3U OpenVPX SOSA™-aligned PWM Servo Motor Drive
68PW1
-
The 68PW1 is a 3U OpenVPX SOSA™-aligned (basis, Snapshot 2) single-axis PWM servo motor drive that can be configured with closed loop feedback measurement options including Hall, Resolver/Synchro or Encoder. The PWM drive provides programmable PWM output drive (up to 65 V @ 10 A continuous) from a single +28 VDC input source. Ideally suited for rugged Mil-Aero applications, the 68PW1 delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems in air, land and sea applications.
-
Product
PWM Servo Motor Drives
-
NAI's PWM Servo Motor Drives provide programmable, PWM output drive (up to 65 V @ 10 A continuous) from a single +28 VDC input source and Drives Brushed or Brushless (BLDC) motors. Available in 3U OpenVPX and VME board constructions and specifically designed for rugged defense, industrial, and commercial applications with a -40°C to +85°C operating temperature range, these PWM Servo Motor Drives deliver a COTS solution for embedded motor control applications.
-
Product
Small Step Broadband Synthesizer
SBC Series
-
*Connectorized Package *Fine Resolution Design *Broadband Designs Available *Low Phase Noise *Ultra-Low Spurs *Optional Internal Reference
-
Product
Digital Control Step Attenuator
-
RF Lambda’s digital control step attenuators are used to fine tune an RF signal using TTL control lines. Fast response time, various step sizes and overall attenuation ranges make these suitable for a variety of RF applications. Hermetically sealed options are available upon request.
-
Product
Step Attenuators
-
A stepped attenuator from Pasternack. Our BNC attenuator is a RF step attenuator design. This 50 Ohm manual step attenuator is precision manufactured to RF and microwave industry specifications.
-
Product
Motor Test Port
MTAP2
-
We know safety is number one priority in any motor reliability program that is why PdMA developed the MTAP2, our answer to safe electric motor testing. With the combination of MCEMAX® or EMAX, the MTAP2 makes testing easier, faster and above all safe!
-
Product
Large Format - Step & Repeat Tester
GATS-8300
-
The GATS-8300 Tester is one in a series of Test Systems designed for testing multiple-image panel using a Step & Repeat process. Rather than fixture the entire panel for electrical test, you simply fixture for one (or more) images. The GATS-8300 will Step the fixture across the entire panel and Repeat the electrical test at each step.
-
Product
Motor and Resolver Control
-
With excellent radiation tolerance and enhanced performance, CAES’ Motor and Resolver Control products are ideal for moving you through space and other harsh environments.
-
Product
Motor Tester
-
FISHER TESTERS AUTOMATIC TEST EQUIPMENT
Dual Station Loaded Motor Tester including Automatic Shaft Engagement, Automatic Bar Code Scanners, Full Spectrum Vibration Analysis (8 bands) with Automatic Accelerometer Placement and Reject Printer.
