Fuel Cell Stack
-
Product
In-Situ Cross- Stack Laser Analyzer
-
LS25 is an in-situ analyzer for non-contact measurement of the concentration of gases. The measuring principle of the LS25 is based on the principle of single line spectroscopy (Tunable diode laser absorption spectroscopy, TDLAS). A single cross-sensitivity-free absorption line of the gas to be measured is selected in the near infrared range. A single-mode diode laser operating at room temperature scans the respective absorption line. By using an opposite receiver, the absorption caused by the sample gas is measured and from this the concentration is calculated. An automatic correction for pressure and temperature changes is possible. In addition, the transmission is displayed respectively output as a signal for preventive maintenance.
-
Product
MASTER FUEL PRESSURE TEST SET
FPT5000
-
*Quickly and easily diagnose fuel-related issues on most major gasoline engine platforms, including domestic and foreign vehicles*In-line adapter configuration allows for easier connection to the fuel system as well as the ability to isolate the supply and return lines independently without disconnecting the adapters from the engine*3-1/2" gauge and hose configuration allows adapters to connect directly to the gauge and bleed-off or connect to the 48" extension hose for applications where additional reach is necessary
-
Product
Stack Gas Analysis System
ENDA-5000 series
-
Continuous simultaneous and high-precision measurement of NOx, SO2, CO, CO2 and O2.HORIBA has over 100,000 CEM systems installed and 30 years of quality and experience. That is the base on which HORIBA's new ENDA-5000 series of stack-gas analysis systems are built. These systems have a small footprint and use cross-flow modulated non-dispersive infrared (NDIR) and magneto-pneumatic detectors that are inherently drift-free. The ENDA-5000 series are superior continuous analysis systems that perform reliably for difficult exhaust gas measurements, when measurement errors cannot be tolerated. This CEM series features a new intuitive touch panel that makes every operation available with the touch of a single button. The ENDA-5000 series systems are also designed for ease of maintenance. They are ideal for a variety of uses, including emissions monitoring from steam boilers, refuse incinerators, and electric power generation plants to assure pollution standards are being met.
-
Product
FC(Fuel Cell) Impedance Measurement System
KFM2150 System
-
The KFM2150 system is a fuel cell impedance measurement system configured with an FC impedance meter KFM2150 and an electronic load PLZ-4W series. Combination of KFM2150 and PLZ-4WA series (0V input type) supports impedance measurement for single cell of fuel cell.In addition to impedance measurement with AC impedance method, KFM2150 system provides IR measurement with current interrupt method.Application software enables test for each characteristic of fuel cell such as I-V characteristics, Constant Current characteristics, Current Interrupt method and Cole-Cole plot by the AC impedance method. Moreover, each test can be performed in a specified order.
-
Product
Portable Fuel Analysis
MINISCAN IR Vision
-
The MINISCAN IR VISION is a high speed, compact and robust FTIR fuel analyzer for the comprehensive and automatic measurement of gasoline, jet and diesel fuels. The analyzer is configured to measure more than 100 fuel parameters and components for fuel blending, for quality inspection and to check compliance with fuel specifications directly at the point of sale.
-
Product
Fuel Injection Tester
FIT13A
-
This basic fuel injection tester includes large and small Schrader adapters, M6-1.00 O-ring adapter, and tee manifold. Includes everything necessary to test the following systems: American Motors; Bosch AFC, MPC European and Japanese (except CIS- use our FIT447); Chrysler Corporation; Ford Motor Company; GM (except TBI- use our FIT446); Japanese fuel injection systems; a The 2-1/2" gauge has a dual scale dial with ranges from 0-100psi and 0-7 bar.
-
Product
TurboFan Test Cells
-
Atec, Inc. is an industry-preferred provider of full scale TurboFan test cell design, construction, maintenance, and refurbishment. Our seasoned aeroengine professionals and comprehensive network of international locations and resources provide our customers with unparalleled expertise and value for their most critical and complex test cell projects.
-
Product
Fuel Injector Tester GM Multiport
FIT457
-
For GM domestic cars with large schrader adapters; light trucks, vans and sport utility vehicles with multi-port. The 2-1/2" gauge has a dual scale dial with ranges from 0-100psi and 0-7 bar.
-
Product
Solar Cell Tester
REOO RO-GTM2615
-
REOO RO-GTM2615 Solar Cell Tester is designed for PV cell manufacturing inspection, enabling fast cell performance inspection and stable electrical quality verification. Built for solar factories, it improves cell testing accuracy and maintains stable operation across PV cell production lines.
-
Product
Load Cell Indicators
-
Procter & Chester Measurements Ltd
The instrumentation will power the load cell. The mV/V signal coming back from the load cell is converted by the indicator and displays the force in a unit (e.g.: Kg, kN, lb – customers choice). The indicators within this range are encased so that the operator can either use it on the move (if battery powered) or be a permanent fixture, e.g.: wall mounted.
-
Product
Voltammetry Cell
SVC-3
-
By using this cell, researchers can run experiments free from gasificationed steam. Also, researchers can get rid of influence of oxygen in the cell by bubbling nitrogen gas. This cell can be utilized with CS-3A Cell Stand. This feature is well suited for measurements of ultraweak current.
-
Product
Radial Flow Cell
-
The wall jet of the sample, after hit in to the surface of the electrode, spreads in three dimensions. After hitting the sample on a thin layer electrode directly, it flows to the perimeter from the center of the radiated electrode, improving the sensitivity.
-
Product
Marine Fuel Sulfur Analyzer
NEX QC MFA
-
Applied Rigaku Technologies, Inc
Specifically designed for marine fuel applications, the new Rigaku NEX QC MFA features an intuitive "icon-driven" touch screen interface for easy operation and a built-in printer for convenience. The shuttered 50 kV X-ray tube and Peltier cooled semiconductor detector deliver exceptional short-term repeatability and long-term reproducibility with excellent element peak resolution. This high voltage capability (50 kV), along with multiple automated X-ray tube filters, provides an analysis of sulfur (S), nickel (N), vanadium (V), iron (Fe) and zinc (Zn) ... all with low limits-of-detection (LOD).
-
Product
Cell Isolation & Analysis
-
Life's complexity originates in cells, spanning cellular structure, genetic diversity, gene expression, and complex tissue formation. Serving as the fundamental unit, cells form the foundation of all biology. Characterization of cells, their processes and interactions can provide insights into areas like medicine, symbiosis, and biological diversity. Bio-Rad supports these inquiries, offering innovative technologies for your cell biology research.
-
Product
Load Cells
-
Morehouse Instrument Company Inc.
When high accuracy and low risk are critical, customers rely on Morehouse Ultra-Precision Load Cells. These strain gauge type load cells are often the choice for companies that want their reference standard to have the lowest possible uncertainties. Lower uncertainties allow for shorter set up times, less frequent standard changes, and fewer standards to maintain.
-
Product
Solar Cell Systems
-
he Solar Cell Scan is a multifunctionalexperimental platform,which is based on the measurement of Quantum Efficiency (QE) . The system employs a turnkey integrated design, which can carry out QE, Reflectivity and Mapping testing functions automatically. There are also modular and customdesigned accessories to adapt to different solar cell samples.
-
Product
Basic Fuel Pressure Tester Kit
FIT450
-
Performs running, residual, rail and flow rate pressure tests.Professional dual scale gauge reads 0-100psi and 0-700 kPa with relief valve and fuel discharge hose.
-
Product
Cross Flow Cell
-
Working electrodes for flow cell are mounted on blocks of PEEK. This resin protects the electrodes from external noise and allows researchers to utilize them regardless the content of mobile phase of HPLC because of their hard, organic solvent-resistance. Glassy carbon is usually chosen for the redox reaction study on liquid chromatography. Platinum, Gold, Carbon paste and Nickel electrodes are utilized for special purposes. Thin Layer Cell has been used as a electrode for research such as flow injection analysis (FIA) and the HPLC.
-
Product
Load Cell
-
Precise and robust and it has been designed to meet the requirements of a wide range of industrial weighing applications: hoppers, tanks, platforms. Is able to work in severe environmental conditions typical of applications in food, chemical and pharmaceutical industries.
-
Product
Live Cell Imaging And Analysis
-
The Incucyte Live-Cell Analysis system is designed to efficiently capture cellular changes where they happen - in the incubator. Capture high-resolution fluorescence and bright field images and record data in real time over hours, days or weeks. From proliferation assays to immune killing of tumor spheroids, this flexible system enables users to observe and quantify complex biological changes in real time. Integrated software simplifies data analysis to speed time to answer while producing publication-quality graphs and plots.
-
Product
MFP-570 Main Fuel Pump
-
The MFP-570 provides main engine burn flow as well as servo flow and engine actuator flow. This two-stage “cartridge type” fuel pump is designed to be inserted directly into the engine fuel metering unit.
-
Product
16CH Battery Cell Simulator
Chroma 87001
-
Chroma Systems Solutions, Inc.
Chroma 87001 Battery Cell Simulator is a high precision, programmable, and bidirectional DC power source with both voltage source and current source functions. In addition, the model can be used as a multi-channel DC power supply or an electronic load as well. A single simulator has 16 channels and each of them can set voltage and current respectively via Chroma software.
-
Product
Basic Fuel Injection Pressure Tester
FIT448
-
This set includes everything to test the following: Bosch AFC, MPC, Digijet/Digifant- (except CIS- use our FIT447) Chrysler Corporation Ford Motor Company General Motors (except TBI- use our FIT446) Japanese Fuel Injection Systems Others using Bendi. The 2-1/2" gauge has a dual scale dial with ranges from 0-100psi and 0-7 bar.
-
-
Product
AC Fuel Flow Signal Generator
TA-100
-
The TA-100 signal generator was designed to facilitate testing of aircraft fuel flow indicators that require two input signals designated as “Drum” and “Impeller”. This generator provides both signals so as to provide a direct interface to the fuel flow indicator under test. The generator also provides switched power out to the unit under test as well as a 5v source for testing the bezel lighting. The original design was built around the requirements for the AMETEK series indicators (pn: 10171 series). This generator simulates a reference and a time delayed signal of appropriate amplitude for an indication of up to 1200pph for the indicator under test. The “PPH Select” switch provides fixed signal delays representing 0, 200, 400, 800, 1000 and 1200pph flow rates respectively, this provides the mechanic with an expedient check of the indicators accuracy. The “PPH Adjust” control allows the mechanic to vary the signal delay throughout the full range and serves as a good method for checking of pointer smoothness from stop to stop. The unit’s front panel also provides test jacks to monitor the “FDR Output” as well as the drum and impeller signals. The TA-100 requires only 28Vdc to operate. This generator provides a very economical approach to any repair facility or flight department as it becomes an alternative to purchasing two bench top signal generators. The TA-100 generator at the very least can provide a simple functional test and eliminate the high cost of exchanging an indicator as a function of troubleshooting the aircraft system.
-
Product
TEM Cells
-
Transverse Electro Magnetic (TEM) cell or Crawford cell (named after its inventor) is used to generate accurate electromagnetic waves over a wide frequency range: DC (0 Hz) to GHz., EM waves generated in the cell propagate in transverse mode and have the same characteristics as a plane wave. It can be used to calibrate E-field broadband probes for testing radiated E-field immunity as well as for measuring radiated emission from a product with a spectrum analyzer/EMI receiver.TEM cell generates a consistent electromagnetic field for testing small RF devices such as wireless pagers, receivers, portable phones, etc.
-
Product
Plate Material Evaluating Cell
-
This quite handy cell is developed in order to evaluate plate material such as metal, semi-conducting plate, etc. In evaluation, a sample plate is sandwiched between cell blocks.
-
Product
Stack Analysis Tool
GNATstack
-
GNATstack is a software analysis tool that enables Ada/C/C++ software development teams to accurately predict the maximum size of the memory stack required to host an embedded software application. GNAT Pro add-on.
-
Product
Vapour Cell Clock
-
A compact fibre-coupled solution for laser locking to alkali vapour cells - easily integrated into existing SolsTiS setups and with simple operation using our Ice Bloc user interface.
-
Product
Ancillary Test Cell Products
-
In addition to our innovative and industry leading AccuDyne AC Dynamometers and DynoLAB Test Automation Systems, SAKOR fully integrates a complete range of ancillary products and subsystems necessary for an advanced test cell. Examples include:*Combustion air consumption measurement and conditioning subsystems*Exhaust handling systems*Fuel consumption measurement and conditioning subsystems*Coolant and oil conditioning systems*Throttle actuators*Spark/Fuel controls*Combustion analysis systems*Complete exhaust emissions analysis systems (per 40 CFR 1065 regulations)*Sound attenuating (up to STC 52) test cell enclosures with several fire suppression options*Process water evaporative cooling tower
