Parallel Interface
Connection between devices transmitting information through multiple conductors simultaneously.
See Also: Interfaces, Serial Interfaces, Bus Interfaces, UI, MIPI, Interface Adapters
-
Product
GPIB Interface Card
PI-31000
-
The Pulse Instruments PI-31000 IEEE Interface Card is a standard GPIB Interface card offered by National Instruments. This interface card is used in applications where the PI-2005 Pattern Generator or other instruments are controlled from a remote system CPU, or it can be used as the system controller when the CompactPCI CPU is the system computer.
-
Product
PCI 16 Isolated Input Digital Interface (10-30V)
8006H
-
Optimized for sensing up to 24V inputs, the 8006H PCI digital I/O interface provides 16 optically isolated inputs for connection to devices including sensors, switches, push buttons, and other user inputs.
-
Product
QuadPOD Conditioning Interface
JT 2147/VPC
-
The JT 2147/VPC is a variant of the JTAG Technologies QuadPOD signal conditioning interface specifically designed for use within Virginia Panel Corporation’s mass interconnect interface. The unit integrates both the JT 2148 transceiver circuitry, two independent, programmable TAP modules (of type JT 2149) and two TAP modules with I/O (of type JT 2149/MPV) on a single board that interfaces via the VPC QuadraPaddle connectors type G20x or G14x.
-
Product
GB-GRAM/GB-GRAM-M Interface Card
Valiant 153M
-
Valiant 153M is a GB-GRAM/GB-GRAM-M (GB-GRAM/M) interface card that allows the simultaneous operation and testing of a commercial- off-the-shelf (COTS) receiver and a GB-GRAM/M. Both receivers are powered and communicate using a single USB mini cable. By integrating a COTS receiver onto the Valiant 153M, users can perform cross-checks to determine if the military receiver is connected and communicating data properly. Both receivers communicate via the onboard USB mini or RS-232 serial connectors. The Valiant test fixture was designed to be nearly the same size as the GB-GRAM/M type I card.
-
Product
Nano Interface Unit
NIU2A
-
NAI’s NIU2A contains an integrated power supply, two function module slots and an optional ARM® Cortex®-A9 processor. This small, low-power unit is ideally suited for rugged military, industrial, and commercial applications. It delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems — in less time, with NO NRE.
-
Product
Analog and Digital Interface
421
-
Three quadrature encoder channels with 16-bit countersFour 12-bit D/A outputsEight 12-bit differential A/D inputs, 50 kHz rateWatchdog timerForty-eight bi-directional digital signals for solid state relay boardsPC/ISA compatible
-
Product
Automatic Liquid Interface Tension Meter,Surface Tension Analyzer,Oil Interface Tension Meter
-
Chongqing Assen Power Equipment Co., Ltd
Our HTID-1 Automatic Interface Tension Tester is used to test various liquid surface tension and interface tension based on the ring method that is simple and high accurate, which is widely applied in electric, petroleum, chemical, medicine, food, and teaching filed.
-
Product
Quadrature Incremental Decoder Interface for VMEbus
VME323
-
The VME323 is an Intelligent Quadrature Incremental Decoder VMEbus Board which can be configured for interfacing quadrature incremental encoders with or without an index channel. In index mode up to sixteen encoders with two quadrature channels and an index channel can be connected, and in non-index mode up to twentyfour encoders with two quadrature channels can be connected. The VME323 operates on two encoder input channels and decodes a pair of out-of phase signals in order to increment or decrement a counter.
-
Product
PCI 96 Channel TTL Digital Interface
8009
-
The 8009 digital I/O interface provides 96 channels of buffered drive digital I/O emulating 8255 mode zero, which can be utilized for PC based control and automation of equipment including sensors, switches, security control systems, and other industrial automation systems. 10K pull-up resistors are included. Optional values are available.
-
Product
Isolated Serial Interface Card
PCI-ICM-2S
-
The PCI-ICM-2S serial communications card can be installed in five-volt PCI-bus computer slots and provides effective communication on long lines in noisy environments. Data lines are opto-isolated from the computer and from each other to assure communication even when large common mode voltages and noise are imposed.
-
Product
Linear Testfixture for VPC iCon i1 Mass Interconnected Cassette Interface (Cassette Not Included) 4 or 10 Positions Blocks, UTT 306 x 248 mm
MG-02-01
-
FEATURES• Linear click system with ball bearings, using gas springs• 10 mm ESD-proof top cover with aluminium reinforcement bars• Steel base cabinet with detachable aluminium back and bottom panels• Detachable interchangeable case system with an 8 mm spring loaded probe protection cover• Base cabinet fitted with a telescopic guide rail and catchTECHNICAL SPECIFICATIONS• Max. number of probes (2000N) 1300 units• Max. PCB height: 60 mm• Linear travel: 12 mm• Max UUT: 306 x 248 mm (wxd)• Outer dimensions: 470 x 490 x 100 x 170 mm (wxdxh1xh2)• Designed for Mass interconnect changeable cassette• Up to a maximum of 4 interface blocks of 160 signals• All interface blocks can be customized
-
Product
TSCOE4 Operator Interface Software Module
-
The TSCOE4 Operator Interface provides a graphical user interface for the operator or the implementer in a production environment. It permits selecting the test sequence and supports parametrization of the test. During the test sequence, the current measurement values are displayed in relation to the relevant limits and the pass/fail evaluations for each individual test. After completion of the test sequence, the global test result is visualized.In addition, there are online statistics available to the user, which show the measurement value distribution within the current batch.The editor which is supplied with the product makes it possible to adapt the user interface language to any new deployment location. Several languages – German, English and Chinese – have already been implemented and are available out of the box.
-
Product
Compact PCIe X4 Gen2 And X8 Gen3 Interface CMOS Camera Family
xiB Family
-
Fastest overall - Bandwidth from 20 Gbit/s to staggering 64 Gbit/s, real data throughput up to 7000 MB/sModern components - High resolution from 12 Mpix to 65 Mpix and 3500 Fps high-speed sensors. Versatile mini camera - Subtle 60 x 60 x 36 mm, 160 grams (1)Longest reach - Can work with optical cable at 300m distancesPower efficient - Low power consumption of mere 6 Watt (1)Cool - Minimal heat dissipation with additional Heatsink or Fan options
-
Product
Power Interface Board 6U, 1 PSU connector with AC pins
106PIBM601-9001R
-
The PIB 6U 1 slot has one power connector P47 with AC pins and connects to the backplane via power bugs with 6/32 screws. It is used to facilitate pluggable power supplies, headers, and utility connectors.
-
Product
PCIe To PXIe Remote Control Interface Kit With Daisy-Chain Facility, 5m Cable
43-921-051-KIT
-
The 43-921 PCI Express-to-PXI Express expansion kit provides control of PXI Express modules installed in a PXI Express chassis using high bandwidth PCI Express technology. The extension kit can provide up to 4GB/s using PCIe Gen 2 x8 signaling. The 43-921 PCI Express-to-PXI Express expansion kit provides additional PXI instruments slots to the host computer by implementing a PCI Express-based control of PXI modules. The technology consists of a 53-921-001 host adapter installed in the host computer, a PCIe x8 cable, and a 43-921-00x, a remote controller with the 3U (Eurocard) expansion module. 53-921-001 comes in a PCI Express x8 footprint and equips with PCIe x8 cable connector.
-
Product
Intelligent Interface Card
IIB-1553-VXI-4C
-
The IIB-1553-VXI-4C is an intelligent interface card which provides 4 independent channels for full MIL-STD-1553 test, simulation and bus analysis functions on the VXI bus. All 1553A, 1553B, McAir and STANAG 3838 variants are supported. Each independent channel may be operated as a concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with a windowed Bus Monitor (BM), or as a stand-alone Chronological Bus Monitor (CBM) with comprehensive multi-level triggering capability. Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. Each channel provides a variable amplitude dual redundant 1553 interface, with 2 Mbytes of dual ported RAM. The board is supplied with C drivers in source code and Windows menu driven software as standard.
-
Product
Ethernet To GPIB Instrument Interfaces
-
ICS's 9055 and 8055 Ethernet to GPIB Instrument Interfaces convert any GPIB instrument into a VXI-11.3 compatible instrument that does not require special drivers and is compatible with the following operating systems: LINUX, UNIX, SunOS, MAC OS X, HP-UX, IBM-AIX and Windows systems with VISA or an RPC library. ICS's 9055 and 8055 use VXI-11 RPC calls for secure communication with virtually any computer. Easily programmed on a PC by making VISA calls or on a MAC/UNIX/LINUX computer with RPC calls. Special drivers are not required. ICS Electronics is the premier VXI-11 device supplier with 100% VXI-11 compliance in every product. To learn more about the VXI-11 protocol and how it benefits your system, download our new VXI-11 Tutorial or a copy of the VXI-11 Specification.
-
Product
ARINC 429 XMC Interface Module
XMC-429
-
Avionics Interface Technologies
16, 32, or 64 ARINC 429 channels (up to 32 Tx & 32 Rx) - Programmable Tx channel output amplitude - Programmable high/low speed operation - Eight (8) Discrete I/O (Four (4) inputs, and four (4) outputs) - Concurrent operation of all Tx/Rx Channels at high data rates - Full error injection and detection - Data capture filtering, 100% bus recording, and physical bus replay - IRIG‐B time code encoder/decoder for data correlation - Conduction-cooling and/or conformal coating available - Designed for extended temperature operations - ANSI Application interfaces supporting C, C++, C#, and .net development - Device driver support: Windows, Linux, and VxWorks (others provided upon request)
-
Product
PCI Express to VME Interface
SIS1100-E2/3104-2
-
The SIS1100-e2/SIS3104-2 interface/bus coupler is the choice for demanding VME readout applications. VME block tranfser speeds up to 160 MByte/s are readily accomplished in conjunction with state of the art VME slave hardware.
-
Product
Quad Port Fiber 25GbE Ethernet PCI Express Server Adapter With Intel E810-CAM1. Ideal For Data Center Networking And Storage Area Networks.
PCIE-2531NP
-
Intel E810 Controller4 25GbE SFP28 portsPCIe Gen. 4 x16 host interfaceLow profile (half length) form factorsSupports SR-IOV based virtualization
-
Product
Parallel Test Systems
-
Our parallel test systems for research and development are highly flexible in use and easily adaptable to different tasks as well as changing piezoelectric materials and designs.
-
Product
PCI Express VXIbus Slot-0 Interface
ProDAQ 3030
-
The ProDAQ 3030 PCI Express VXIbus slot-0 interface is a C-size, register-based VXIbus module providing a direct connection from a PC to a VXIbus mainframe using the high-speed PCI Express serial bus. Together with any of the available host cards, the ProDAQ 3030 enables users to use a laptop, desktop, or server computer as an embedded controller. Optimized for low latency and high throughput, it provides a high-performance but cost-effective solution for a data acquisition system.
-
Product
Dual SDI-Analog Video-GPIO Interfaces
FM510
-
Sundance Multiprocessor Technology Ltd.
The FM510, an air cooled Video I/O FMC, is used for standard-definition (SD) and high-definition (HD) video processing in combination with I/O and control applications. The front panel contains two HD-BNC connectors as primary video interface and a high0-density connector for secondary video and I/O interfaces.
-
Product
PMC Compatible Bi-Directional Serial Data Interface
PMC-BiSerial III
-
The PMC BiSerial family has been updated to include a Spartan III [Xilinx] based card with expanded capabilities.. Building on the knowledge and experience gathered from multiple IP and PMC BiSerial implementations and adding in the latest technology has created the PMC-BiSerial-III. The BiSerial III features completely isolated FIFOs with 32 bit ports for increased adaptability and performance.
-
Product
Manual Fixture Kit With Mass Interconnect Cassette Interface, Max number of probes (2N) 1000 units, Max UUT 450 x 330 mm (wxd)
CMCSK-07-01
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
13 GHz Differential Probe with ProLink Interface
DH13-PL
-
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
