PC
Checking personal computers and using a pc as host to perform test.
-
Product
USB Sensor Link
90386
-
The 90386 is a portable sensor interface that powers and processes strain gaged based sensor into USB compatible signals. No need for additional signal processing or special PC cards.
-
Product
USB 2.0 Protocol Analyzer
LE-650H2
-
LE-650H2 is the hardware-based USB analyzer, which can record a large amount of data on the HDD/SSD of the PC, display translation with each class decode, and measure VBUS power consumption. The analyzer automatically detects the High/Full/Low speed of USB2.0/1.1 and starts measuring by simply pressing the space bar of the PC. The low cost device of easy operation by connecting it to the USB port of the PC is useful for developing/debugging the firmware/driver and study purpose of USB standard.
-
Product
High-Performance USB-Controlled PLL Synthesizers
-
Rugged, SMA-connectorized designs that support a USB 2.0 interface with a PC supplying DC power and GUI command control. They cover a broad range of frequency bands from 25 MHz to 27 GHz. These USB-Controlled PLL Synthesizers deliver output attenuation that is adjustable up to 50 dB in 1 dB steps and high output power levels ranging from +10 dBm to +19 dBm typical. Phase noise is as low as -108 dBc/Hz at 100 MHz offset and phase locked speed is 1 msec typical.
-
Product
High and Low Temperature Humidity Chamber
GDJS/GDJW
-
•The chamber is produced by SUS304 Steel, the temperature keeping material is produced by Polyurethane hard foam and ultra-fine fibre glass, the doorframe heat insulated by Double high temperature aging silicone rubber door sealing strip. •The temperature controller is used by Korean TEMI display in English/Chinese and German Siemens PLC, it can be communicated to PC via RS-232. The temperature accuracy is 0.1℃ and humidity is 0.1%R.H •The temperature sensor is platinum PT100 Ohms/MV resistor •The heating system is full separately system which produced by Nickel chromium alloy electric heating type heater •The cold system is applied by fully enclosed fan cooled single-stage and cascade refrigeration mode, the compressor is from France TECUMSEH brand which can allow you get after sales support from many countries •The cyclical system is applied by High temperature low noise air conditioning type motor and Multi blade centrifugal wind wheel •The safety self-protection function include Electric leakage, short circuit, over temperature, motor overheating, compressor pressure, overload, over-current protection •Working Power: AC380V±10% 3phases and frequency 50Hz/60Hz •Working Environmental: Temperature is 5℃～+30℃ Humidity ≤85%R.H
-
Product
PRECISION GAUGE
PVX
-
PVX is equipped with an alpha-numeric data logger to provide increased versatility for those custom reporting needs. The high speed scan feature speeds up the inspection process by making 32 measurements per second. Remove transducer from the test material and display the minimum measurement scanned.Visual and audible alarm with hi and lo limit settings for specific application tolerances. Auto find features locates the detection point(s) and adjusts the display settings to bring the waveform into view. PVX comes complete with our Windows PC software for transferring data to and from a PC.
-
Product
12-Bit PCI Express ADC/Digitizer
SIS1350
-
The SIS1350 is our first PC add on digitizer card. It was developed for high repetition rate acquisition of short analog signals (i.e. up to 128 µs at 500 MSPS) with good resolution
-
Product
PC Based Power Monitor
11P-Link
-
1P-LINK compact interface box is the choice for users who want to do all power meters control as well as the analysis from their computer. With its impressive features for statistics calculation and display options, the 11P-LINK is also an answer to scientific or OEM users who need a low-cost computer based power monitor
-
Product
Leeb Hardness Tester
THL500
-
It is the highest brightness display in China showing all functions and parameters, easy read Largest screen Oled screen and operate,also can save lots of energy .the largest screen of Leeb hardness tester in China. Two hardness scale dual-display in the screen. Measuring direction in 360 and add the auto measure direction to make test easy and precision. Add four new hardness scales, HRA, HB for D impact device of alloy tool steel; HV for cast aluminum alloy. Add New user material function, to meet the need of user can test the special material. Test at any angle, even upside down. Wide measuring range. It can measure the hardness of all metallic materials. Direct display of hardness scales HRB, HRC, HV, HB, HS, HL and three types of strength values immediately. Seven impact devices are available for special application. Automatically identify the type of impact devices. Large capacity memory could store 600 groups (Relative to average times321 ) information including single measured value, mean value, testing data, impact direction, impact times, material and hardness scale etc. Upper and lower limit can be preset. It will alarm automatically when the result value exceeding the limit. Battery information indicates the rest capacity of the battery and the charge status. User calibration function. USB port with the PC humanity multi-functions data proceeding software. Original imported high speed thermal printer support the immediate printing function. It can save data permanently. Li rechargeable battery as the power source. Charge circuit integrated inside the instrument. Continuous working period of no less than 200 hours (EL off and no printing). Auto power off to save energy. Excellent after-sale service system for high quality products---3 years guarantee and all life maintenance. Easy to buy and comfortable to use.
-
Product
Pt100 Temperature Transmitter PC Programmable With Push Button Calibration
SEM1605/P -
-
SEM1605/P - Pt100 Temperature Transmitter PC Programmable With Push Button Calibration
-
Product
Sound Level Assessment System
05NK002
-
Ideally equipped for carrying out Noise at Work risk assessments, as well as the majority of environmental survey work the Risk Assessment System comes with a choice of Class 1 or Class 2 logging sound meter, calibrator, case and PC download software.
-
Product
USB to GPIB Controller
Model 488-USB2
-
* Adds GPIB Controller capability to any PC with a USB port.* Fast >1 Mbs transfer rate * Most affordable USB GPIB controller with an industry standard GPIB-32.dll.* 488.2V4 Driver supports 32 and 64-bit versions of Windows XP, Vista, Windows 7, 8 and Windows 10 with a true 64-bit DLL.* Uses industry standard 'ib' and '488.2' command sets.* Works with Agilent, NI and Kikisui VISA libraries.* Program with Visual Basic, C, Agilent VEE, LabVIEW, or MATLAB.* ICS's Explorer auto configures your controller as it finds your instruments.* Use ICS's Explorer to control your instruments without having to write a program.
-
Product
2-Channel Mandrel Free IL/RL Test Station
-
Shanghai Fibretool Technology Co.,Ltd.
This test station is designed specially for different connector on both sides patch cord(such as FC-SC, FC-LC, SC-LC…) and the duplex patch cord.The REF for insertion and return loss can set one time for those kind of patch cord, no need to change standard patch cord and interchange testing port connector on tester( Especially 2.5mm and 1.25mm interchange). For the tested patch cord, APC end no need to manually set standard patch cord length if PC end measured shortest length is 2.2M.
-
Product
Pulsar 4 Channel Interface
Pulsar-4 7Z01201
-
Ophir’s 4 channel Pulsar interface turns your PC or laptop into a full fledged Ophir multi-channel laser power/energy meter. Just install the software, plug the laser measurement sensor into the Pulsar and the USB cable from the Pulsar to the PC USB port. With the Pulsar-4, you can connect up to 4 laser measurement sensors to each module, monitor each pulse at up to 25 kHz and utilize external trigger.
-
Product
CORROSION GAUGE
MVX
-
The MVX finishes the line of MX gauges with class. This thing is loaded with all of the features of the MX gauges and a lot more. Four selectable display options: RF, Rectified, B-Scan, and Large Digits. An internal data logger that stores a total of 12,000 readings and waveforms, 64 user custom definable setups, selectable transducer table for improved linearity, thru paint mode with the single press of a button, multiple calibration and material selection options, and auto waveform find just to mention a few! Equipped with a single element flaw prove-up mode for basic angle beam inspections. This is all nicely packaged in a very mini portable aluminum extrusion for extra durability and portability! The MVXview java-based PC software makes this thing a complete kit, and then some!
-
Product
Robust Din-rail Fanless Embedded System With RISC-based (iMX-287) Processor 4 COM, 2 CAN Bus And DIO
rBOX610
-
The rBOX610 din-rail fanless embedded system utilizes the low power RISC-based module (iMX-287) processor and is designed to withstand temperatures ranging from -40°C to +70°C for using in extreme operating environment and industrial automation applications. The rBOX610 box PC features 4 RS-232/422/485 serial ports, dual LANs, 4 digital input channels,4 digital output channels, 2 CAN bus and 1 eMMC onboard 4 GB & 1 x SDHC socket for storage expansion (easy to access) in a compact, IP40 protected, industrial-strength robust case. Two power paths input minimize the risk of data loss in the event of a single power failure. Its vertical din-rail form factor makes it easy to install the system in a small cabinet. Due to the RISC-based architecture, rBOX610 will not generate a lot of heat while being operated. The ready-to-run rBOX610 is specially designed for remote control/monitoring management applications like unmanned control room, industrial machine, automatic parking lot, traffic cabinet and more.
-
Product
Data Acquisition PCI Card
UPC2100
-
The UPC2100 PCI Sensor Interface card provides real-world data acquisition and control for your PC. Up to 16 sensor inputs in any mix or combination are accepted by the UPC2100. No external signal conditioning is required. The UPC2100 includes configuration and data acquisition software and is compatible with C#, .NET, C++, Visual Basic, LabView.
-
Product
Remote Data Acquisition
-
Sometimes your sensors or the piece of equipment you are trying to control is not in a convenient place to have a PC close by. The sensors may be widely distributed through out your plant and it just wouldn’t be cost effective to run all your wiring to where the PC is. In addition, low level signals are more accurately acquired when digitized close to the signal source. In all these cases our REMOTE ACCES line of products will help. The REMOTE ACCES pods are intelligent, sensor to computer interfaces. Each pod can be used as an autonomous data logger to acquire data for later download. Or as many as 31 pods may be connected on a single two wire multidrop RS-485 network allowing a cable distance of up to 4000 ft. You can also go wireless and extend your range by adding RS-485 wireless transceivers to your serial port. Each unit comes in a rugged NEMA 4 enclosure and can withstand harsh industrial and marine environments.
-
Product
cPCI Backplanes
-
CompactPCI bus is compatible, in terms of electrical specification, with the PC world’s PCI bus. The mechanical specifications were adapted to the commonly used Euro-board plug in systems for 19" racks.
-
Product
DDR4 BGA Interposers, DDR4 DRAM X16 Packages
N2115A
Interposer
The N2115A DDR4 BGA Interposers are soldered in between the DRAM and PC board or DIMM raw card where the DRAM would normally be soldered. They are designed with the PCB or DIMM foot print on the bottom side and the DRAM footprint on the top side. The signals from the memory controller chip and DRAM are then passed directly to the top side of the BGA probe adapter where they can be accessed with the oscilloscope probes.
-
Product
Portable Connector End Face Geometry Interferometer
-
Thorlabs’ Vytran® Connect-Chek® Interferometer automatically and precisely measures radius of curvature, apex offset of polish, and fiber undercut or protrusion on any PC or APC, single-fiber connector. The CC6000 interferometer uses a non-contact tilted-phase-analysis technique for fast, reliable measurements of connector end faces. This compact interferometer has a carrying handle and must be attached to a desktop or laptop computer (not included) with a standard USB 2.0 port for operation. The included CC6000 software, which is used to control the interferometer, can be installed on a computer with the minimum requirements in the table below. Designed for use in both the factory and the field, this interferometer provides crucial quality information needed to assure long-term performance of fiber optic connectors. One CC250P Mount for Ø2.50 mm PC Connectors and one RT250P Reference Tool for calibrating the CC250P mount are included with the CC6000 interferometer; mounts and reference tools that enable measurement of other PC or APC, single-fiber connectors are available separately below. When used with an appropriate mount for APC connectors, the CC6000 interferometer is also capable of measuring the APC angle and key error.
-
Product
EQCM Electronic Quartz Crystal Microbalance
Elettra
-
Elettra has been designed to operate on its own, but it is also possible to connect it to a PC to control it and acquire, view and save data thanks to its extremely easy to use software that runs under MS-Windows™. The data acquisition process can be controlled extremely quickly thanks to the PLAY, PAUSE and STOP keys.
-
Product
DataBlaster PCI / PCIE JTAG Boundary-Scan Controller
JT 37x7/PCI
Controller
High speed and performance JTAG Boundary-scan PCI PC plug-in controller for PCI bus slot or PCIe PC plug-in controller for PCI Express bus slot.The controllers are targeted at demanding manufacturing test applications, fast in-system flash memory programming and programmable logic configuration. The JT 37×7 is available in different operating levels (memory options) to suit your specific environment and application. Each unit is supplied with a four TAP port signal conditioning module the JT 2147 ‘QuadPOD‘
-
Product
Emulates Atmel T89C5111
FE-5111
-
* Emulates Atmel T89C5111 * 4K Code Memory * Real-Time Emulation and Trace * Frequency up to 33MHz/5V * ISP and X2 Mode Support * MS-Windows Debugger For C And Assembler * Emulation Headers and Signal Testpoints * Target Board and Programmer Included * Serially Linked to IBM PC at 115Kbaud
-
Product
PC Link Software
LE-PC800G
-
*The PC Link is software that provides an efficient measurement environment utilizing the high-resolution screen and high-capacity HDD of a PC.*The analyzer can be remotely controlled by the PC so that measurement data will be displayed on the screen or continuously recorded on the HDD.*The PC Link incorporates versatile features (e.g., a search function that finds target data exactly, a TEXT-CSV conversion function that is useful for the generation of reports, and Japanese-English display).
-
Product
Low Cost Emulator
EB-51X2
-
* Emulates 8051 Derivatives with 6/12 Clocks/Cycle * 64K Code And 64K Data Memory * Memory With Mapping Capabilities * Real-Time Trace * Frequency Range up to 40MHz * Source-Level Debugger For C And Assembler * MS-Windows Debugger Software * Performance Analyzer * Emulation Header and Signal Testpoints * Serially Linked to IBM PC at 115Kbaud
-
Product
X.25 Adapters & XOT
-
FarSite supply the world’s largest range of X.25 adapters for PCs, Servers and Laptops a USB adapter, 2 and 4-port PCI Express adapters. 2 and 4-port Universal PCI adapters. 2 port PMC adapters and XOT software for Linux.
-
Product
Digital Multimeters
-
*5½-digit resolution to 8½-digit resolution DMMs*6ppm basic voltage measurement accuracy on the 8½-digit DMM for calibration laboratories*Fast, 1 Msample/s sampling speed to capture complex, low level current profiles from IoT devices or other wireless devices*Sensitivity of 1 µΩ and 1 pA to test low power devices for research, design, and manufacturing test*A wide range of measurement functions such as DC and AC volts, DC and AC current, two- and four-wire Ohms, continuity, frequency, period, RTD, thermistor, and thermocouple temperatures, diode test, and capacitance*Numerous interface options including LAN/LXI, USB-TMC, GPIB, and RS-232 for data acquisition and automated testing*Intelligence to execute tests and create customized measurements with minimal PC interaction*Measurement expansion up to ten channels
-
Product
Surface Mount-to-DIP JEDEC SOT-25, SOT-23A-6 Adaptor
1110748
-
Surface Mount to DIP Adapter for SOT-25, SOT-23A-6. Allows for breadboarding or substitution of microgate SOT-23A-6 and SOT-25 IC and transistor packages into .100 [2.54] pitch proto boards or PC boards. Solder masked top-side pads allow user to hand solder devices directly to topside of adapter with fewer problems of solder bridging. Longer male bottom pins are available at special request for easy use of probe clips. Large topside pads allow for soldering test pins, jumpers, etc. to top of adapter.
-
Product
DC Load Bank
K-900
-
Kongter Test & Measurement Co., Limited
K-900 series are your best choice DC load bank with Kongter’s updated solutions. This new series resistive dummy load includes a series customized load bank models that feature rugged design and and excellent performance. They facilitate your work for DC load and battery capacity testing. With different models of DC load bank, it covers a wide range from 12V to 480V nominal voltages with current up to 600A. Its big TFT touch screen with vivid display makes it more user-friendly for setting and operation. Kongter’s new PC software make it easy for measurement monitoring and report print out.
-
Product
Ethernet/LXI hybridNETBOX 16 Bit Digitizer and AWG - 180 MS/s Digitizer on 2 Channels, 1.25 GS/s AWG on 2 Channels
DN2.827-02
Digitizer
The hybridNETBOX DN2.82x series internally consists of a Digitizer and an AWG that can run together or independently. That allows simultaneous data generation and data acquisition for stimulus-response tests, ATE applications, MIMO applications or closed-loop applications. Used independently, the digitizer can acquire test data in the field and the AWG can replay this test data in lab. The hybridNETBOX offers 14/16 bit resolution and is available with digitizer sampling rates of up to 500 MS/s and AWG sampling rates of up to 1.25 GS/s. The hybridNETBOX can be installed anywhere in the company LAN and can be remotely controlled from a host PC.
