Solder Paste Inspection
assures volume and area of paste application.
See Also: Solder Paste, Solder Paste Measurement, 3D Solder Paste Inspection
-
Product
Simple 3D Measurement & Inspection
XG-X Series Vision System
-
Abundant processing power is available even with multiple camera connections, including the 21 megapixel color camera, line scan cameras, or 3D cameras. XG-X Series offers high-speed, high-resolution cameras for high-accuracy inspection, providing powerful solutions for a variety of problems that arise in manufacturing.
-
Product
Smart Inspection Station
SiS
-
Smart Inspection Systems LLC was born in 2010 in response to orthopedic manufacturers’ demands for faster inspection than their sister industries. Our signature product, the Smart Inspection Station™ (SiS™), is an automated turnkey inspection solution that yields comprehensive visual reports with complete geometric form and dimensional pass/fail in just minutes. The SiS™ is custom-configured per the client’s needs, yet versatile enough for simultaneous commissioning on multiple product lines. The product of years of refinement, the SiS™ gives comprehensive visual reports with complete geometric form and dimensional pass/fail in just minutes. Your SiS™ can be custom-configured according to your needs, but is still versatile enough for simultaneous use on multiple product lines. And best of all, every SiS™ purchase comes with ongoing support from L3I’s expert staff.
-
Product
Entry-level X-ray Inspection System
X-eye 5100 Series
-
100kV ~ 130kV Micro-focus Closed tube and high-definition Flat Panel Detector are installed and high-resolution image can be gained.Customer convenience is primarily considered in operation and maintenance of the product.Customization is available because it is specially designed to be add up any necessary functions depends on customer needs with reasonable prices.
-
Product
Wafer Inspection System
-
JRT Photovoltaics GmbH & Co. KG
In close cooperation with well-known providers of inspection systems, we provide modular systems for quality control and classification of raw wafers.
-
Product
37-Pin D-Type Female Solder Pin HV
92-960-037-F-HV
D-Sub Female Connector
This accessory is designed to allow users to directly terminate a cable with soldered connections. When the product is used without a backshell users should make their own cable strain relief arrangements and ensure appropriate electrical safety precautions are observed.
-
Product
Chip Inspection System
GEN3000T
-
GEN3000T is an inspection system that performs automatic inspection of individual semiconductor chips.This revolutionary chip surface inspection system was achieved by combining the chip handling technology cultivated by Toray with the inspection algorithm used in the "INSPECTRA®" wafer defect inspection system.
-
Product
Inspection Cameras
-
The inspection camera opens a new view into the insides of machines and systems; whether an endoscope, thermal imaging camera or infrared thermometer - an inspection camera is the ideal instrument for monitoring and maintenance.Due to the flexible control of the endoscope or the visual display of potential damage areas in machines or systems, weaknesses and points of failure can be detected and therefore be prevented. The inspection camera make this possible without the need for complex disassembly.The inspection camera is used by electricians, safety experts, expert witnesses, mechatronics, and mechanics. The inspection camera is also used for apprenticeships and in-service training. An inspection camera can be applied internally as well as at school or at universities for demonstration purposes. With their help, inspections in the industrial sector can be organized considerably faster, more targeted and more cost-efficient. An inspection camera is an important companion in the course of everyday work.
-
Product
Semiconductor Package Inspection System
-
NIDEC-READ GATS (Grid Array Testing System) series carry out open/leak circuit tests on semiconductor package (MCM/CSP/BGA).
-
Product
Waterproof Inspection Cameras
-
waterproof inspection cameras have waterproof probes, General's DCS6XX wet/dry cameras, the DCS600A, DCS605, DCS660A, DCS665 & the DCS665-ART, go one step further because their grips and monitors are also waterproof. This feature, unique in the industry, allows users to inspect toilets and water and sewer lines carrying running water without worrying about dropping and "dunking" the instrument.
-
Product
Digital Inspection
-
The DI-1000 and DI-1000L-PRO inspect fiber optic connector endfaces, providing clear sharp digital images on your Windows® PC. The DI-1000 and DI-1000L-PRO use LIGHTEL's Series 2 Tips and come with a soft case designed to fit easily into a standard laptop case.
-
Product
Integrated NDT Inspection Device
FlawHunter
-
The FlawHunter is an integrated NDT inspection device, equipped with an advanced, high-resolution Laser Shearography sensor with a vacuum (partial) excitation system. It is ergonomic & easy-to-use and is equipped with a workflow-oriented, GUI-display and left/right-hand button control. Regardless of the application, the FlawHunter provides reliable and resolute measurement results for in-field (service) NDT and quality control (post-production) operations.It can be used on any material & surface provided a stable vacuum can be generated within the vacuum seal (viewable inspection area).
-
Product
Smart Factory Inspection System
-
API, recognizing manufacturing industry’s increasing demand for part measurement automation, with a higher degree of accuracy, has developed its Smart Factory Inspection System with true 6 Degrees of Freedom (6DoF) real-time 3D robotic measurement incorporating its proven metrology technology and calibration components.SFIS can be delivered as a customized integrated solution or as a standard production inspection cell.
-
Product
Hi-Definition Video Inspection Station
VIS800
-
Video Inspection Stations are available with?or without on-screen measurement capabilities?and offer?an excellent way to evaluate or test small works or items in?difficult to access locations.? As todays electronic and mechanical systems keep getting smaller, it becomes impossible to test or measure these products with traditional methods. For many applications, from development to production testing, video based inspection can help maintain quality control. Many of these systems are used in labs for development or used in production for testing production samples.
-
Product
Electronic Inspection Systems
-
Intego's knowhow even makes it possible to identify challenging defects that may be located under the surface. One system is the inspection of chips by means of lock-in thermography, which visually represents the IR radiation intensity signal of electronics. Special lasers and flash lamps generate a very short heat impulse (10 ms) on the chip, which generates a measurable heat flow. In most cases, a resolution of < 1 μm can be achieved.
-
Product
3D Automated Optical Inspection
Zenith UHS
-
High-speed full 3D AOI that brings about a revolution in SMT process management Industry-leading speed for full 3D measuring inspection equipment skill solutions- Only solution in the industry to set inspection criteria according to IPC-610 standards- Performs defect diagnosis through measurement-based data and eliminates the causes of possible errors- Powerful 3D solder joint inspection
-
Product
Defect Inspection Module
EB40
-
The Class 1 certified E40 and B40 modules (available separately or combined in one module) can automatically detect defects on the entire edge, from zone 1 to 5, and the entire backside. The ability to inspect the entire backside allows for faster root-cause analysis of zone 5 defects since such defects can migrate from the wafer interior.
-
Product
Protective Coating Inspection Kit 3
-
Measurement parameters include:Surface profileSurface temperatureClimatic conditionsCoating thicknessAdhesion
-
Product
Automated Optical Inspection (AOI)
-
Automated optical inspection (AOI) is an automated visual inspection of printed circuit board (PCB) (or LCD, transistor) manufacture where a camera autonomously scans the device under test for both catastrophic failure (e.g. missing component) and quality defects (e.g. fillet size or shape or component skew). It is commonly used in the manufacturing process because it is a non-contact test method.
-
Product
Power Transmission Line Inspection System
-
Shandong Senter Electronic Co., Ltd
With the aid of high-end technology and equipment, Senter Electronic manufactures and trades high-tech power transmission line inspection system with low price. And we are known as one of the leading such manufacturers and suppliers in China for our quality products and good service. Welcome to buy the power transmission line inspection system with our factory.
-
Product
High-Accuracy Automated Optical Inspection Systems
-
Fully-automated and high-accuracy 3D inspection and measurement systems. High-power, long working distance optics and high-resolution digital camera are perfect for high-magnification applications. These are full-color systems capable of high-accuracy measurements, automated defect detection and color verification.
-
Product
68-Pin Micro-D Male Solder Bucket With Backshell
40-962B-068-SB-M
SCSI Male Connector
This connector is designed to allow users to directly terminate with soldered connections to the 68-Pin SCSI Style Micro D connector. Pickering Interfaces recommends the use of purchased cable assemblies for applications where most or all of the contacts are in use.
-
Product
Video Inspection Probe
-
With today's high data rates and high definition services, connector quality and inspection has never been so important. Research reveals that up to 75% of all optical network failures are attributed to poor connector quality - reduce your installation time and ensure your network is reaching its full potential.The Video Inspection Probe (VIP) application for Anritsu field testing platforms gives operators a safe, easy way to analyze and document connector conditions.
-
Product
Metrology & Inspection Systems
-
Our optical and e-beam wafer metrology and inspection products quickly and accurately measure pattern quality before and during high-volume chip manufacturing.
-
Product
Bulkflow X-Ray Inspection System
-
Designed to be integrated into line with optional reject stations, the Bulkflow X-ray System is perfect for loose and free flowing products. Offering a good detection levels on a wide range of contaminants including all metal, bone, glass and dense plastics.
-
Product
In-Line Wafer Surface Defect Inspection
ALTO-SD-150/200
-
ALTO-SD SERIES IS AN IN-LINE INSPECTION SYSTEM SUPPLYING HIGH THROUGHPUT, FULL SURFACE DEFECT INSPECTION FOR ALL KINDS OF WAFERS INCLUDING SILICON, QUARTZ, SAPPHIRE, COMPOUND AND MEMS WAFERS. HIGH-RESOLUTION CAMERA OPTICS PLUS LED ILLUMINATION GUARANTEE RELIABLE DETECTION OF ALL LOCAL DEFECTS. IT INSPECTS DEFECT SIZE OF 1~ 10 MICRONS, CONFIGURABLE INSPECTION RESOLUTION TO OPTIMIZE DEFECT SIZE VS. THROUGHPUT. THE SYSTEM COMBINES HIGH-PRECISION MEASUREMENT, POWERFUL DATA ANALYSIS AND USER-FRIENDLY OPERATIONS.
-
Product
Solder Paste Wetting Tester
SP-2
-
SP-2 is wettability testing machine forsolder paste, parts electrode and PC board,adopted SP-Tension-Method (Temperature Profile Method).
-
Product
Mini Coax, Contact, Receiver, Solder Sleeve, RG316 & RG178
610104142
Coax Contact (Receiver)
Mini Coax, Contact, Receiver, Solder Sleeve, RG316 & RG178.Mechanical SpecificationsDurability 20,000 cyclesContact Material Shield – BrassCenter Conductor – BeCuContact Plating Shield – 30µ" Au over 100µ" NiCenter Conductor – 60µ" Au over 100µ" NiContact Termination Solder SleeveInsulator PTFEMating Force 1.5 lbs max [0.68 kg]Electrical SpecificationsCharacteristic Impedance 50ΩFrequency Range DC to 2 GHzVSWR ≤ 1.2 @ 2 GhzInsertion Loss ≤ 0.05 dB @ 500 Mhz≥ -0.3 dB @ 2 GhzDWV 1500 VDC Min.Contact Resistance ≤ 5 mΩCable Specifications RG316 & RG178Environmental SpecificationsOperating Temperature -50°C to +105°CInsulation Resistance 1000 MΩ min.
-
Product
9-Pin D-Type Male, Solder Bucket, HV
40-960-009-M-HV
D-Sub Male Connector
9-Pin Male D-Type Connector, High Voltage, Solder Bucket - With Backshell
-
Product
Borescopes & Inspection Cameras
-
Triplett Test Equipment & Tools
Is an inspection camera with a detachable wireless 3.5" color display. It features 4x digital zoom, water resistant 8mm camera with 3.5ft cable, and 4 adjustable white LEDs for illumination.The wireless display detaches from the handle for additional freedom in viewing, and internal magnets will conveniently mount it to steel surfaces. With the included Micro SD card you can save snapshots and live video. Saved files can be viewed on the LCD screen or downloaded to a computer via the USB port.
-
Product
Conformal Coating Inspection (CI AOI)
-
They cover the components, the area around the components and identify most coating issues including cracks, bubbles, insufficient / excess coating, loss of adhesion and other common contaminations. Full coverage inspection for conformal coating.
