Fiber End Face
-
Product
Optical Fiber Sensors
-
Optical sensors based on Fiber Bragg technology (FBG) are a reliable and safe solution for numerous testing applications, such as in structural testing and lightweight construction. Benefit from perfectly-matched measurement chains when using an optical FBG sensor based on Fiber Bragg Gratings made by HBM FiberSensing.
-
Product
MIL-STD-1553 Fiber Optic Bus Extender
FO-1553
-
Avionics Interface Technologies
Extends MIL-STD-1553 bus access to over 1 mile for remote access - Dual redundant, single and dual stream options available - Both Transformer and Direct coupling modes supported - Uses fiber optic 1.0625 Gbps data rates for low latency over long distances - Optical signaling is not affected by electrical noise and interference - Simple and easy to use solution, no software setup or configuration required - Ideal for applications where test equipment is separated from UUT
-
Product
Cable Assembly, 9-Pin D-Type, Male to Unterminated With Cut Ends, 1m, HV
A009DM5-C-HA100
Cable Assembly
A range of 9-Pin D-Type High Voltage cable assemblies with unterminated connections on one end, constructed from PTFE Type C insulated wire. The unterminated connections are coded to match the connector pin designation.
-
Product
LXI Dual 8 Channel Fiber Multiplexer ST, Multi-Mode
60-851-312
Multiplexer Module
The 60-850 and 60-851 are LXI conformant fiber optic multiplexers that use MEMS switching technology to ensure fast and reliable switching of single-mode (60-850) or multi-mode (60-851) optical signals being carried on fiber connections. The 60-850/851 is available with a variety of connector options and in a variety of multiplexer arrangements. Loop-thru versions are also available for easy multiplexer expansion.
-
Product
Fiber Optic Temperature Sensor with the EasyDisk
The TPT-62
-
The TPT-62 fiber-optic temperature probe family employs industry standard 62.5µm core OM1 fiber optic for highly improved optical, mechanical, and reliability properties over legacy 200 µm core (1st generation) fiber optic sensors. The EasyDisk sensor tip assembly ensures IEC60076-2 (Annex E) compliant installation and enables quick insertion of the probes into the spacers within the windings of transformers.
-
Product
Cable 96-Pin Micro-D Female to Unterminated, Tinned Ends, 1m
A096SFR-T-5A100
Cable Assembly
The 96-Pin SCSI Style Micro-D to Unterminated Cable Assy is constructed from 28 AWG Twisted Pair Tinned Copper wire with Polyolefin insulation. Crosstalk is minimised. Wires are colour coded for easy connection. Metal Spring Latches are provided on the 96-Pin connector.
-
Product
LXI Single 32 Channel Fiber Multiplexer SC, Single-Mode With Loop-Thru
60-850-224
Multiplexer Module
The 60-850 and 60-851 are LXI conformant fiber optic multiplexers that use MEMS switching technology to ensure fast and reliable switching of single-mode (60-850) or multi-mode (60-851) optical signals being carried on fiber connections. The 60-850/851 is available with a variety of connector options and in a variety of multiplexer arrangements. Loop-thru versions are also available for easy multiplexer expansion.
-
Product
Cable Assembly, 25-Pin D-Type, Male to Unterminated With Cut Ends, 0.5m
A026HM5-C-0A050
Cable Assembly
The 26-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 7/0.15 (26AWG) Silver Plated Copper Wire. The connector can be secured to an associated product by screwlocks. The unterminated connections are coded to match the connector pin designation. Please ensure appropriate electrical safety precautions are observed when using this product.
-
Product
InfiniiMax Differential/Single-ended Connectivity Kit
E2669B
-
Includes a differential browser, four solder-in differential probe heads, and two socketed differential probe heads.
-
Product
3-Pin Power D-Type Cable, Male to Unterminated, Tinned Ends, 2m
A003PM5-T-5A200
Cable Assembly
The 3-Pin Power D-Type cable assembly is constructed from 50/0.26mm2 (14 AWG) Tinned Copper Wire with PVC insulation. Screwlocks are provided to secure the connectors to their associated products.
-
Product
PXI/PXIe MEMS Optical MUX, 8-Channel, Multi-Mode, 50/125 Fiber, MU Connectors
42-852A-318-M50
Multiplexer Module
The 40/42-852A-318-M50 is a PXI/PXIe 8-channel multiplexer with MU (mini SC) connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules.
-
Product
20-Pin GMCT Cable, Male to Unterminated, Tinned Ends, 10A, 0.5m
A020GMR-T-0C050
Cable Assembly
The 20-Pin GMCT cable assembly is constructed from 19/0.254 (18AWG) Tinned Copper Wire with PFA insulation. Screwlocks are provided to secure the connector to associated product. The unterminated connections are coded to match the connector pin designation. Users may need to make their own cable strain relief arrangements when using this product and should ensure appropriate electrical safety precautions are observed.
-
Product
Fiber Optic Components For Optoelectronic Packaging
-
OZ Optics offers a wide range of standard and custom fiber optic components for optoelectronic packaging. Components include collimators, focusers, patchcords, connectors, and metalized fiber. The low backreflection collimators and focusers are available for a wide range of industry-standard connectors and wavelengths. The hermetically sealable patchcords, with glass or metal solder, and metalized fiber meet high Telcordia standards. The polarization maintaining patchcords and connectors use our specially designed ferrules that minimize insertion loss, backlash, and rotational errors.
-
Product
Cable Assembly, 50-Pin D-Type, Female to Unterminated With Cut Ends
A050DF4-C-0A050
Cable Assembly
The 50-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated wire and can be secured to the product by screwlocks. The 50-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
Product
Cable Assembly, 78-Pin D-Type, Female to Unterminated With Cut Ends
A078HF5-C-0A100
Cable Assembly
The A078HF5-C-0A100 is a 78-Pin D-Type to Unterminated cable assembly constructed from 7/0.15 (26AWG) Silver Plated Copper Wire. Screwlocks are provided to secure the cable connector to associated products. Has a 45 degree cable exit towards pin 1.
-
Product
Cable Assembly, 50-Pin SGMC, Female to Unterminated, Tinned Ends, 5A, 1m
A050FFR-T-0A100
Cable Assembly
This is a 0.5m long female to unterminated 50-Pin SGMC cable assembly with ferrules and is constructed from 19/0.18 (21AWG) Copper Wire with PFA insulation. Screwlocks are provided to secure the connector to associated product.
-
Product
4 Way Fiber Optic Return Path Receiver (low Optical Input)
MX4RR-LI
-
The MX4RR-LI transforms return optical signals to RF signal output. The standard 1U chassis integrates 4 independent receiver modules, it can receive up to 128 return optical signals from burst mode mini-nodes or services for 128 RFoG optical network units (ONU)-Mini-Nodes.
-
Product
PXI Single 2 Channel Fiber MUX ST
40-855-512-M
-
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
Fiber Interferometers
-
Wuhan Sunma Technology Co., Ltd.
SunmaFiber Interferometer is an automatic, non contact fiber endface interferometer for single fiber connector developed by SunmaFiber. It is designed to measure the geometry parameters of single fiber connector end-face. Equipped with auto focus and auto centering functions, SUNMA INTERFEROMETER is very accurate and stable, it can also test bare fiber and bare ferrule. It is very helpful in fiber connector manufacturing to increase the quality of the connectors.
-
Product
Portable Connector End Face Geometry Interferometer
-
Thorlabs’ Vytran® Connect-Chek® Interferometer automatically and precisely measures radius of curvature, apex offset of polish, and fiber undercut or protrusion on any PC or APC, single-fiber connector. The CC6000 interferometer uses a non-contact tilted-phase-analysis technique for fast, reliable measurements of connector end faces. This compact interferometer has a carrying handle and must be attached to a desktop or laptop computer (not included) with a standard USB 2.0 port for operation. The included CC6000 software, which is used to control the interferometer, can be installed on a computer with the minimum requirements in the table below. Designed for use in both the factory and the field, this interferometer provides crucial quality information needed to assure long-term performance of fiber optic connectors. One CC250P Mount for Ø2.50 mm PC Connectors and one RT250P Reference Tool for calibrating the CC250P mount are included with the CC6000 interferometer; mounts and reference tools that enable measurement of other PC or APC, single-fiber connectors are available separately below. When used with an appropriate mount for APC connectors, the CC6000 interferometer is also capable of measuring the APC angle and key error.
-
Product
EV Power Components End of Line Test Platform
Test Platform
Test and Validate all EV Power Electronics with One Flexible and Scalable Solution
-
Product
PXI/PXIe MEMS Optical MUX, Dual 2-Channel, Single-Mode, 9/125 Fiber
40-855A-022-HI
Multiplexer Module
The 40/42-855A-022-HI is a PXI/PXIe dual 2-channel multiplexer with FC/APC connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
Cable Assembly, 25-Pin D-Type, Male to Unterminated With Tinned Ends, 0.5m
A026HM5-T-0A050
Cable Assembly
The 26-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 7/0.15 (26AWG) Silver Plated Copper Wire. The connector can be secured to an associated product by screwlocks. The unterminated connections are coded to match the connector pin designation. Please ensure appropriate electrical safety precautions are observed when using this product.
-
Product
LXI Single 32 Channel Fiber Multiplexer FC/APC, Single-Mode With Loop-Thru
60-850-024
Multiplexer Module
The 60-850 and 60-851 are LXI conformant fiber optic multiplexers that use MEMS switching technology to ensure fast and reliable switching of single-mode (60-850) or multi-mode (60-851) optical signals being carried on fiber connections. The 60-850/851 is available with a variety of connector options and in a variety of multiplexer arrangements. Loop-thru versions are also available for easy multiplexer expansion.
-
Product
Cable Assembly 68-Pin Micro-D Male to Unterminated, Cut Ends, 2m
40-972-068-2m-MU
Cable Assembly
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by a Metal Spring Latch.
-
Product
Fiber Optic Test Kit
FIP-920-SM
-
The SYOPTEK FIP series Pro Single Mode/Multimode Fiber Optic Test Kit is the perfect all-in-one fiber optic test equipment kit. The FIP kit provides a wide selection of fiber optic testing, cleaning, and inspection equipment to enable technicians to install, troubleshoot and maintain fiber optic networks. It is really a cost-effective and easy-to-use solution for testing single mode and multimode fiber optic networks, troubleshooting of fiber networks.
-
Product
3 Ft Harness, 78-Pin Male Connector On One End, Loose Wired (Numbered) Other End
GT97102
-
3' harness, 78-pin male D-sub connector on one end, loose wired (numbered) other end.
-
Product
Cable Assembly 15-Pin D-Type, Male to Unterminated With Cut Ends, 1m
A015DM5-C-0A100
Cable Assembly
The 15-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper Wire. The connector can be secured to the associated product by screwlocks. The unterminated connections are coded to match the connector pin designation. When using this product additional cable strain relief arrangements may be necessary and appropriate electrical safety precautions should be observed.
-
Product
3-Pin Power D-Type Cable, Female to Unterminated, Cut Ends, 1m
40-972-403-1m-FU
Cable Assembly
The 3-Pin Power D-Type cable assembly is constructed from 50/0.26mm2 (14 AWG) Tinned Copper Wire with PVC insulation. Screwlocks are provided to secure the connectors to their associated products.
-
Product
Optical Fiber 4×1 Switch
OFSW - 4 × 1
-
Hangzhou Huatai Optic Tech. Co., Ltd.
OFSW-4×1 is a 4×1 prism optical switch. It can support 4 optical fibers input and 1 fiber output, channel switch. Wide operating wavelength range, low insertion loss and speedy switching rate, can use network trends configuration, network monitor and lab application.
