Fiber End Face
-
Product
Optical Fiber 1×8 Switch
OFSW - 1 × 8
-
Hangzhou Huatai Optic Tech. Co., Ltd.
OFSW- 1×8 is a 1×8 prism optical switch. It can support 1 optical fibers input and 8 fiber output, channel switch. Wide operating wavelength range, low insertion loss and speedy switching rate, can use network trends configuration, network monitor and lab application.
-
Product
Fiber Optic Network Simulators
SIM-2FON-25
-
Vconsole fiber optic network simulator is custom built portable unit intended to simulate installed fiber optic facilities. Vconsole will design and build custom unit exactly to customers specification. The enclosure is capable of housing an individual spool with up to 100km of fiber. We will build each unit to client unique needs with custom fiber types, lengths, and connectors. A full range of connectors are available including SC, ST, FC, and LC types.This product is ideal for latency testing, product development and training and educational needs.
-
Product
20-Pin GMCT Cable, Male to Unterminated, Cut Ends, 16A, 2m
A020GMR-C-1B200
-
The 16A 20-Pin GMCT cable assembly is constructed from 19/0.41 (14AWG) Copper Wire with PFA 500V insulation. Screwlocks are provided to secure the connector to associated product. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated.
-
Product
VTAC, Patchcord, ITA, 36", VTAC, DVI-D, Double Ended
7-141877141-036
-
VTAC, Patchcord, ITA, 36", VTAC, DVI-D, Double Ended
-
Product
Cable Assembly, 50-Pin D-Type, Male to Unterminated With Tinned Ends, 1m
A050DM4-T-0A100
-
The 50-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated wire and can be secured to the product by screwlocks. The 50-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
Product
Fiber Optic Visual Fault Finder
VFF5
-
Used to verify continuity, test and find breaks in fibre links, locate pinched fibre strands in termination cabinets, or anywhere fibre optic cables are terminated and subject to mechanical damage.
-
Product
Single 4 Ch Fiber Optic Multiplexer
40-810-014
-
Pickering PXI Fiber Optic Multiplexers connect a single channel to one of two or four channels. They are available in single or dual multiplexer configurations supporting single-mode or multi- mode fiber. A wide choice of connectors types is available. The 40-810 multiplexer connects the optical channel by redirecting the optical signal into a selected output fiber.
-
Product
Single Fiber Bi-Direction EDFA
HA8000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
HA8000 series, is a bi-directional fiber amplifier with high-quality. It can transmit and amplify downlink and uplink signal on one fiber. It offers an economical solution to network operators when utilizing the existing fiber source, upgrading networks and providing bi-directional VAD business.
-
Product
MXI-Express Cable, Gen 1 x1, Fiber Optic, 10m
778959-10
-
MXI-Express Cable with Communication Levels up to Gen 3 x8 - The MXI-Express Cable connects a host interface to a PXI or PXI Express chassis. You can also use it for data communication between multichassis systems. NI offers it in different MXI communication levels and lengths.
-
Product
Front End Protector
AS-RXFEP RX
-
The AS-RXFEP Receiver protector limits input RF signal threshold from 1 to 150MHz to less than 0.3 Vrms to protect a receiver front end from damage due to nearby transmitted signals. The receiver still actsnormally and measured signal strength is not affected.The circuit uses a multi-stage design of transformer saturation coupling and current limiters. It also incorporates a low voltage GDT to protect from lightning events. These are for receiving only - you cannot transmit through them without damaging the unit.
-
Product
Multi Mode Fiber Optic Rotary Joints
-
Multi Mode Fiber Optic Rotary Joints (FORJ) can be supplied as a stand alone product with customized features (wavelength, connectors, fiber).
-
Product
PXI/PXIe MEMS Optical MUX, 8-Channel, Multi-Mode, 62.5/125 Fiber
40-852A-118-M62.5-HI
-
The 40/42-852A-118-M62.5-HI is a PXI/PXIe 8-channel multiplexer with FC/PC connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
High Power Fiber Optic Visual Fault Locator
VFL-700
-
Shanghai Fibretool Technology Co.,Ltd.
The VFL-700 is specially designed for field personnel who need an efficient and economical tool for fiber tracing, fiber routing and continuity checking in an optical network during and after installation.
-
Product
4 Ports 1GbE Fiber Bypass Network Management Card
NMC-0120
-
Ideal for network segmentation applications and inline security monitoring. 1x Intel® I350_AM4, 4 x LC(SX or LX) fiber connectors with fiber bypass module, 1 x PCIe 2.0 x4, Gen2.
-
Product
Fiber Splitters & WDMs
-
Wuhan Sunma Technology Co., Ltd.
Optical Splitter is used to split the fiber optic light into several parts at a certain ratio. It is an important component used in Passive Optical Network (PON), therefore also called PON Splitter. There are mainly two kinds of PON splitters: one is the traditional fused type splitter known as FBT Coupler or FBT WDM splitter, which features competitive price; the other is the PLC Splitter based on the PLC (Planar Lightwave Circuit) technology, which has a compact size and suits for density applications. SunmaFiber provides both PLC splitters and FBT coupler splitters for EPON/GPON Systems.
-
Product
1 Channel VGA Over Fiber Transmitter and Receiver Extender
L-1VGA-FE
-
The QuestTel L-1VGA-FE Fiber Optic Transmitter and Receiver provides long haul transmission of high resolution VGA and Audio control signals over a single fiber up to 20km.
-
Product
C-Band Separate Raman Fiber Amplifier
RFA5000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
1. Erbium-doped Fiber Amplifier, due to the multiple cascades and the accumulation of noise caused by spontaneous emission, will reduce the system CNR greatly and thus it will limit the transmission capacity and distance of the system. Raman Fiber Amplifier (RFA) is a newly designed fiber amplifier based on Stimulated Raman Scattering (SRS) effect. It is considered as the core technology of new generation DWDM fiber over-long communication. Compared with Erbium-Doped Fiber Amplifier, Raman amplifier has the advantage of low Noise Figure (NF), wider gain bandwidth, flexible gain spectral region and stable temperature. It is the only device that can operate in 1300~1600 nm.
-
Product
C-Band Separate Dispersion Compensation Raman Fiber Amplifier
DRA5228/F
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Raman Fiber Amplifier (RFA) utilizes the optic gain in the Stimulated Raman Scattering (SRS) in the optical fiber and realizes the amplification of the signal optic. FRA, with very low equivalent noise and a wide gain scope, can further widen the gain bandwidth by adopting multi-wavelength optical bump, which represents the development direction of the new optical fiber amplifier.
-
Product
Cable Assembly, 50-Pin D-Type, Male to Unterminated With Cut Ends
A050DM5-C-0A100
-
The 50-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated wire and can be secured to the product by screwlocks. The 50-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
Product
Fiber Optic Light Sources
-
Fiber optic light sources are a necessity for performing optical fiber network testing to measure the optical fiberal loss for both single mode fiber cable and multimode fiber cables. They are designed to cover a variety of wavelength ranges to suit all optical testing needs and usually the optical light sources are used with the optical fiber power meter to test the fiber system loss. Light sources are offered in a variety of types including LED, halogen and laser. Usually the optical light source is used with the optical fiber power meters, they act as an economic and efficient solution for the optical fiber network works.
-
Product
Cable Assembly, 78-Pin D-Type, Female to Unterminated With Cut Ends
A078HF4-C-0A050
-
A 78-Pin D-Type to Unterminated cable assembly constructed from 7/0.15 (26AWG) Silver Plated Copper Wire. Screwlocks are provided to secure the cable connector to associated products. Has a 45 degree cable exit away from pin 1.
-
Product
Powerful 1 µm Femtosecond Fiber Laser
FemtoFiber ultra 1050
-
The FemtoFiber ultra 1050 is part of TOPTICA's third generation of ultrafast fiber lasers. The system delivers laser pulses of 90 - 100 fs in duration at a central wavelength of 1050 nm. Using a power amplifier the system provides more than 5 W average output power. It is a compact femtosecond laser system with turnkey operation and cost-effective design.
-
Product
Cable Assembly 15-Pin D-Type, Male to Unterminated With Cut Ends, 0.5m
A015DM5-C-0A050
-
The 15-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper Wire. The connector can be secured to the associated product by screwlocks. The unterminated connections are coded to match the connector pin designation. When using this product additional cable strain relief arrangements may be necessary and appropriate electrical safety precautions should be observed.
-
Product
PXI/PXIe MEMS Optical MUX, 4-Channel, Single-Mode, 9/125 Fiber, FC/PC Connectors
42-850A-114
-
The 40/42-850A-114 is a PXI/PXIe 4-channel multiplexer with FC/PC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules.
-
Product
Optical Fiber Splicing Tool Kit
SAT-02B
-
Shaanxi Aitelong Technology Co., Ltd
SAT-02B Tool kit is wonderful for optical fiber fusion splicing. It includes the most frequently required tools for preparation and cleaning optical fibers before cleaving and splicing. And well fits to Aitelong model SAT-17S and SAT-17M fusion splicers.
-
Product
6FE+2x100M Multi-Mode SC Fiber Port Industrial Managed Ethernet Switch
EKI-7708E-2MI
-
Provides 6*FE ports with auto MDI/MDIX, Provide 2x100M SC Multimode 2km ports, Support 10/100Mbps auto negotiation. Support jumbo frame transmission up to 10k, Provide slim size, DIN-rail with IP30 metal mechanism, Support redundant 12V~48V DC power input and P-fail relay.
-
Product
PXI/PXIe MEMS Optical MUX, 4-Channel, Multi-Mode, 62.5/125 Fiber, FC/PC Connectors
42-850A-114-M62.5
-
The 40/42-850A-114-M62.5 is a PXI/PXIe 4-channel multiplexer with FC/PC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules.
-
Product
Fiber Optic Pressure Seals
-
Columbia Research Laboratories
Fiber Optic Pressure Seals are designed to provide a safe, convenient, reliable method of exiting fiber optic data lines through a structure while preserving the integrity of either a pressure or vacuum environment.
-
Product
3-Pin Power D-Type Cable, Female to Unterminated, Cut Ends, 1m
40-972-403-1m-FU
-
The 3-Pin Power D-Type cable assembly is constructed from 50/0.26mm2 (14 AWG) Tinned Copper Wire with PVC insulation. Screwlocks are provided to secure the connectors to their associated products.
-
Product
Measurement Front End of the ACQUAlab Generation
LabBGN
-
labBGN is the first of the new ACQUAlab generation of measurement front ends. It is used in conjunction with the background noise simulation systems 3PASS HAE-BGN/ HAE-car, the communication analysis system ACQUA and other HEAD acoustics components.
