Circuit
-
Product
Door Contact Sensor
ENVIROMUX-M-DCS
-
Monitors access with a magnetic bridge sensor, which responds to any magnetic material (no special inserts necessary). Can also be used for monitoring side wall and covers. Includes mounting hardware. For normally closed circuit connection. 2-wire interface. Screw terminal. Maximum cable length: 1,000 ft. Wide actuating gap, approximately 1". Dimensions WxDxH (in): 0.5x0.5x2 (Switch), 0.5x0.5x2 (Magnet). Operating temperature: 32 to 158°F (0 to 70°C). Regulatory approvals: RoHS.
-
Product
Multifunction Tester
EASYTEST
-
EASYTEST carries out tests on electric systems in compliance with IEC/EN 61557-1 and therefore measurements of continuity of the protection cable, insulation resistance (with calculation of PI and DAR), overall earth resistance, RCDs type A and AC tripping time and current, line / fault impedance with calculation of prospective short circuit / fault current, phase sequence and conformity.
-
Product
Switch
TOE 9261
-
Toellner Electronic Instrumente GmbH
Input voltage 60 V, Output current up to 100 A, Rise / fall time < 500 ns, Short-circuit-proof, Switchable discharge of load circuit, Interruption in supply and ground lines up to 100 A, Switchable buffering of input circuit, 4 signal line switches, Control with any signal generators (TTL level)
-
Product
Thermalyze Extension for Steady State Analysis
Lock-In
-
Steady-state thermography is limited to detecting hot spots that heat up a minimum of 100 mK (0.100°C). This may be useful for locating shorts on high-power devices, but is inadequate for detecting low power defects such as semiconductor device leakage current or short circuit with very low or very high resistance. Steady-state thermography also suffers from poor spatial resolution as the heat from localized hot spots diffuses rapidly, blurring the location of the heat source.
-
Product
Radio Frequency (RF) And Microwave Products
-
Enable your 5G, aerospace, defense, test and measurement or industrial RF wireless applications with our portfolio of RF and microwave devices. These include high reliability RF diodes, Gallium Nitride (GaN) and Gallium Arsenide (GaAs) Monolithic Microwave Integrated Circuit (MMIC) amplifiers, frequency translation and power transistor devices, switches, attenuators, varactors, filters and more.
-
Product
Tri-phase High Power Programmable AC Power Source
APS50000
-
Advanced direct digital frequency sythesizer(DDS) waveform generation technology, high frequency stability, good continutyMeasurement precision is high, suitable for current half-sinusoid and its similar waveforms with DC component measurementProvide embedded intelligent PC monitoring systemAdjustable output voltage from 0 to 150V, 0 to 300V, step distance 0.1VOutput frequency 45-120Hz(40-500Hz optional), step distance 0.1 HzOutput current limiting functionWith 9 sets of memory, you can store commonly used parameters for easy invocation when using themWith RS232C communication interface 【IEEE488.0(GPIB)optional】, instruction execution times is less than 10mSProtechtion mode: over voltage, over current, overload, short circuit,current limit, ectProvide RMS voltage, RMS current, active power, frequency, power factor, ectFor 100% load removal, voltage stabilizing reaction time within 20ms, strong overload capacity, instantaneouscurrent can with stand 3 times of rated current
-
Product
PXI 5W Programmable Resistor Module, 2-Channel, 1Ω to 122Ω
40-252-112
Programmable Resistor Module
The 40-252-112 is a programmable resistor module with 2 channels which can be set between 1Ω and 122Ω with 0.5Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
Product
Microwave Probes
S-Probe
-
S-Probe series of single-ended probes can perform up to 20 GHz are designed for RF, power integrity, and signal integrity testing. Its strong beryllium copper (BeCu) tips is perfect for direct probing of uneven surfaces, such as solder pads and circuit components. This is a big improvement over the fragile microprobes.
-
Product
Power Management ICs (PMICs)
-
Telecommunications and defense industries demand ever-increasing functionality in equipment such as satellites, probes and spacecrafts. CAES offers a family of radiation hardened Power Management Integrated Circuits (PMICs) designed for high reliability applications.
-
Product
Limiting Amplifiers
-
Chengdu KeyLink Microwave Technology Co., Ltd.
Keylink's limiting amplifiers use FET device with good consistency and distributed traveling wave amplifying circuit to design. Good amplitude and phase consistency characteristics can be achieved in a wide input dynamic range. It's the key component of the electronic system. Keylink's limiting amplifiers can be categorized as follows.
-
Product
Lightning Current Generator
-
Shanghai Guantu Technology Co., Ltd.
The lightning wave impulse current generator is an impulse current generator that generates a simulated lightning current waveform . Its working process is as follows: first, the transformer charges the capacitor bank through the silicon pile, when the charging voltage reaches a predetermined value, the spark gap is triggered, and the capacitor is discharged through the total inductance and total resistance of the circuit. When the resistance is greater than or equal to the critical damping value, a unidirectional impulse current wave is generated in the circuit. When the resistance is less than the critical damping value, an oscillating impulse current wave is generated. The magnitude of the impact current amplitude is related to the circuit parameters. When the capacitance value and charging voltage are the same, the smaller the inductance value, the greater the current amplitude. In order to obtain as much current as possible, a pulse capacitor with a small inductance value is usually selected, and the total length of the connecting line should be as short as possible when arranging the main capacitor, so that the total loop inductance value can be reduced as much as possible.
-
Product
Ethernet
-
Ethernet and fiber optic networks are critical components in business service delivery. The DataScou... t family of multi-service network analyzers enables providers to equip technicians to install and troubleshoot next generation networks effectively, while continuing to support legacy transport services. Tempo Communications offers service providers powerful, all-in-one solutions that span future and past technologies, making the transformation from legacy transport circuits to advanced multi-gigabit services an easy one. The DataScout family is designed to ensure maximum efficiency while lowering costs associated with installing, maintaining, and troubleshooting networks.Show less
-
Product
Power Quality Analyzer
PQM-700
-
*power to the analyzer is supplied from tested mains (internal power supply) and is used in all types of networks from 64 V to 760 V, with particular emphasis on measurements at low voltage poles, due to the ease of connection,*has an independent power supply socket, especially suited for voltage measurements for transformers and DC circuits,built-in real-time clock.
-
Product
Fiber Optomechanics
-
The versatile FiberBench product line includes Single and Multi-Axis FiberBenches as well as a wide variety of compatible components ranging from beamsplitter modules to wave plate units. FiberBenches form the foundation of a nearly infinite array of miniature fiber optic systems that customers have been building for the last decade. When used with the FiberPort Collimators/Couplers, a complete optical circuit can be constructed. The Fiber Launch Platforms are ideal for coupling a free space laser into a single mode, multimode, or polarization-maintaining fiber. Other accessories include fiber mounts, fixed and kinematic collimator adapters, and L-bracket mating sleeves.
-
Product
Vector Network Analyzers
-
The VIA Bravo is a handheld Vector Impedance Analyzer for measuring the impedance and resonant frequencies of circuits and antennas. The VIA Bravo has the capability of providing accurate measurements and sweep displays of impedance, reactance, resistance, phase angle, return loss and SWR. The VIA Bravo’s testing functionality, combined with its 100 kHz to 200 MHz frequency range, make it a versatile tool for many service applications including areas such as MRI, wireless telemetry, 2-way radio, aviation, and Radio Frequency Identification (RFID).
-
Product
1 GHz, 1 MΩ, 0.9 pF Active Probe
ZS1000
-
Engineers must commonly probe high frequency signals with high signal fidelity. Typical passive probes with high input R and C provide good response at lower frequencies, but inappropriately load the circuit, and distort signals, at higher frequencies. The ZS Series features both high input R (1 MΩ) and low input C (0.9 pF) to reduce circuit Loading across the entire probe/oscilloscope bandwidth. The ZS1000 is ideal for 200–600 MHz oscilloscopes.
-
Product
Multi-Channel, Programmable Current Source
CS-48-100
-
The Model CS-48-100 is a multi-channel, programmable current source. Developed for both semiconductor and digital superconductor electronics, it is computer-controlled and features 48 low noise current source outputs. Each source output has the capability to both set and read back currents and can be set to a zero current high Z mute state. Each of the 48 sources are optically coupled for control and are sourced from their own secondary winding for complete galvanic isolation. The device consumes a maximum of only 80 W and handles a maximum load current of 4.8 A total over all outputs. Operating over a range of 0-100 mA on each channel, the device features accuracy of +/-25 ?A. The mute state can be set thru a rear panel interlock or from the front panel button for maximum circuit protection. The unit can be mounted in a standard-sized rack.
-
Product
General Purpose Low-side MOSFET Drivers
-
Renesas' family of low-side FET drivers are very high-speed matched dual-drivers capable of delivering peak currents of 2.0 amps into highly capacitive loads and excellent at driving large capacitive loads with minimal delay and switching times. The high-speed performance is achieved by means of a proprietary "Turbo-Driver" circuit that speeds up input stages by tapping the wider voltage swing at the output. Improved speed and drive capability are enhanced by matched rise and fall delay times. These matched delays maintain the integrity of input-to-output pulse-widths to reduce timing errors and clock skew problems. This improved performance is accompanied by a 10 fold reduction in supply currents over bipolar drivers, yet without the delay time problems commonly associated with CMOS devices. Dynamic switching losses are minimized with non-overlapped drive techniques.
-
Product
Short Circuit Loop Impedance Meter
AMZC-305
-
Loop impedance measurement with resolution 0,01Ω ; Loop impedance measurement without tripping the circuit breaker > 30mA with resolution 0,01Ω (100...440V) ; Measurements possible in installations 110/190V, 115/200V, 127/220V, 220/380V, 230/400V, 240/415V, 290/500V and 400/690V (range 100...750V)
-
Product
Torque Transducers
-
The technology behind our torque sensors are strain gages. These gages are arranged into a Wheatstone Bridge circuit, which converts the physical, mechanical force into an electrical signal that can be filtered, displayed, and recorded for further processing. This very accurate radiometric electrical signal is proportional to the applied mechanical force.
-
Product
6 Contacts- Circuit Breaker Analyzer
CB14
-
The CB14 is a 6 contacts circuit breaker analyzer designed to perform Timing, Motion as well as Static & Dynamic Resistance Measurement (DRM) in a single test. It also includes 3 multifunction analog inputs.
-
Product
Frequency Multipliers
-
A series of broadband frequency multipliers is available with output frequencies between 18 and 110 GHz. The use of GaAs diodes on a suspended substrate circuit allows an extremely compact device. Circuit symmetry is used to enhance either even or odd harmonics while suppressing unwanted odd or even harmonics. These devices can be used as higher order even or odd harmonic multipliers with reduced efficiency. All of these multipliers have maximum input power +23 dBm for temperature less than +50°C.
-
Product
Parametric Analyzer
-
FA Instruments Parametric Analyzer offers all the functions of a 'big box' circuit testing solution, without the 'big box' footprint!The Parametric Analyzer is an advanced software module that can performs within the Crystalvision suite. The module provides all the functionality and testing schemes you would expect from a high-end solution, with all functionality being geared towards providing the maximum information to the FA engineer.
-
Product
Cable Testers
DMX ADAPTER
-
DMX protocol is a standard means of controlling lighting dimmers remotely from a control desk. The standard uses a three wire connection using 5-pin XLR type connectors. These adapters allow the E445, E446 and E447 table testers to be used to test the primary circuit of such cables. Two adapters are required for each cable tester.
-
Product
Transformer Test Panel/ Setup
-
This is a common test panel for distribution/ power transformers of different specifications. The user can perform most of the factory tests, as per the relevant IS standard for the transformers. The panel consists of power analyser, meters for high voltage test, meters for induced voltage test etc, control for all the tests, protection and interlock circuits so that a single panel can be used to conduct a number of tests using only one dimmerstat and the associated devices
-
Product
Primary Test Manager
-
The Primary Test Manager™ (PTM) software supports you during diagnostic testing, condition assessment and data management of medium- and high-voltage assets, such as circuit breakers, rotating machines, grounding systems, instrument and power transformers as well as bushings and on-load tap changers (OLTC).
-
Product
Reliability Testing
-
ELES Semiconductor Equipment SpA
ELES designs and manufacturers reliability test solutions to verify the performance of integrated circuits from concept validation to high volume production during all the test phases. No other company can provide universal equipment for all the reliability tests, or can guarantee a seamless data flow between phases or can apply on chip embedded reliability engineering for data tracking and failure investigation. Clients use our functional test data to proactively analyse variations between lots, between temperature extremes and during lifetime (often these defects escape ATE). The improvements to products and processes needed to arrive at zero defects cannot be driven by the quantity of Big Data alone, the quality of reliability data is a strategic advantage that only ELES can provide.
-
Product
Filters / Splitters / Detectors
-
DiCon’s 100 GHz WDM is designed to multiplex and demultiplex signals in multi-wavelength systems based on the ITU 100 GHz grid. The component uses a thin film filter mounted between a pair of GRIN lens collimators. The 100 GHz WDM is housed in a compact, environmentally stable package that offers superior resistance to humidity and temperature and is suitable for mounting on a printed circuit board or within a module.
-
Product
Continuity Testing
-
The checking of an electric circuit to see if current flows (that it is in fact a complete circuit).
-
Product
FMC Mezzanine Module
NES-FMC4ADC
-
Sundance Multiprocessor Technology Ltd.
By default this card only uses signals from the LPC rows of the HPC connector that is mounted. The gain can be set by software in three steps: +/-50mV, +/-0.5mV, and +/-5V. AN advanced offset circuit is used in the front-end design of the ADC board, and allows a voltage shift in the range og +/-5V that is independent of the chosen gain range.
