Response
-
Product
PCI Programmable Resistor Card 2-Channel 2.5 Ohm To 2.04k Ohm - SPST
50-294-122
Programmable Resistor Module
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Impedance Analyser Frequency Response Analyser
C60
-
The C60 investigates the opaque world of analog networks. The unit operates in two test modes. It can measure the frequency response of a two port system producing a gain/loss and phase graph. It can also measure the reactive response of a two terminal network producing an impedance/admittance and phase graph. Electronic, electrical, electro-acoustic and other networks can be tested with sine wave excitation and the results displayed on a PC.
-
Product
Security/Detection
ST120 Dual
-
A two-channel silicon-based thermopile in a TO-5 package. Each small active area is 1.2mm x 1.2mm . Time constant of 25ms with Nitrogen encapsulation gas. Delivers a very low Temperature Coefficient of Responsivity of -0.04%/C. This detector has a very short thermal shock response to ambient temperature change.
-
Product
Rapid PSE And Chained Data Test Of 4-Pair And 2-Pair PSE's
PSL-3424 Quick Test for 802.at and 802.3bt PSE's
-
Accessible from PSA Interactive or PowerShell PSA. Scans 2 to 8 PSE ports per test cycle. Automatically determines and adapts to PSE maximum assigned class. Tests PSE’s that grant full power via PD Classification or through PoE LLDP. Validates PoE Detection Acceptance and Rejection Range. Measures PSE Port Voltage at both minimum (DC MPS) and maximum (Pclass) load conditions. Reports PSE type (AT vs BT), maximum assigned class capability, and Pclass power capacity. Assesses Disconnect Power Removal response. Assesses Overload Power Removal response. Assesses LLDP Power Protocol and Allocations (PSL-3424L).
-
Product
Low Noise Prepolarized Microphone
378A04
-
The 378A04 is a matched system that is comprised of a high sensitivity microphone and a low noise preamplifier that contains a built-in filter that enables the free-field response to remain flat over a wide frequency range. The system requires a minimum of 4 mA and measures to 6.5 dBA (5.5 dBA typical) within a cost efficient, prepolarized (0V) design. PCB's model 378A04, the industry's first prepolarized low noise microphone and preamplifier system allows you to measure extremely low amplitudes. In the past this was only possible with externally polarized solutions. With a typical noise floor of 5.5dBA, this microphone system delivers all of the benefits commonly associated with prepolarized systems.
-
Product
Power Detector Laser Power Meters
11PMK-H5
-
Fast, Small Size, Flat Spectral Response, Full NIST-Traceability, High Damage Threshold: 36 kW/cm² to 45 kW/cm², Personal Wavelength Correction™, Low profile, Air and Water cooled, Energy mode, Effective aperture diameter 19 mm (area 2.84 cm²)
-
Product
Signal Conditioners
Frequency to Voltage
-
Encore Electronics offers a complete line of frequency to voltage converters ranging from the economically priced and compact DIN rail mounted Model FL228 to the rack mounted Model 225. For applications requiring performance between these two models, we now offer our FL236 DIN-rail packaged Digital Frequency/Voltage converter, featuring fast response time, low power and compact footprint.
-
Product
Audio Oscillator & Sweep Generator
SweepGen
-
SweepGen turns a PC into an Audio Oscillator and Sweep Generator which can be used for testing audio or educational purposes. In conjunction with audio test instruments, you can make frequency response plots. SweepGen uses the sound card in your PC to produce sine waves that are mathematically correct almost to CD quality, indeed it's more likely that the quality of your PC sound card will be the limiting factor rather than the code in SweepGen.
-
Product
PXIe-4147, 4-Channel, ±8 V, 3 A Precision PXIe Source Measure Unit
786888-01
Source Measure Unit
PXIe, 4-Channel, ±8 V, 3 A Precision PXI Source Measure Unit - The PXIe-4147 is a 4-channel source measure unit (SMU) ideal for high-pin-count applications. It features 4-quadrant operation, and each channel has integrated remote four-wire sensing for accurate measurements. The sample rate of the PXIe-4147 can reduce measurement times, capture transient device characteristics, and help you perform current-voltage (I-V) characterization of devices-under-test (DUTs). With a high-speed sequencing engine, you can synchronize SMUs with each other or with other instruments such as switches or high-speed digital test modules. Additionally, you can tune the PXIe-4147 response to any load to achieve optimum responses with maximum stability and minimum transients using SourceAdapt technology.
-
Product
50/100G PAM4 Pin Photodiodes
-
Macom Technology Solutions Holdings Inc.
MACOM offers high sensitivity PIN photodiodes with industry leading performance at speeds of 56Gbd / 100G. Proprietary designs enable operation using PAM4 modulation protocols in 50 /100G applications. The high responsivity designs have high reliability and are suitable for use in both tele-communications and datacenter networks. The high bandwidth PIN photodetectors are available in a back illuminated design (highest performance), a front illuminated design (more cost effective) and in both singlet and array form factors
-
Product
Dual Accelerometer
M6
-
*Built-in damping and overrange stops*Safe overrange limits*Force up to 2000 G without damage to sensor*Temperature compensated for accurate response over entire temperature range*High slew rate operational amplifiers (1.2 V/usec)*Internal RF shielding on each pin
-
Product
Solid State Broadband High Power Amplifier
Model 2215
-
The 2215 is suitable for octave bandwidth high power CW, modulated, and pulse applications. This amplifier utilizes high power GaN devices that provide wide frequency response, high gain, high peak power capability, and low distortions. Exceptional performance, long-term reliability and high efficiency are achieved by employing advanced broadband RF matching networks and combining techniques, EMI/RFI filters, and all qualified components. The amplifier is constructed within a single 5RU drawerincluding the forced air-cooling. Available operating voltage configurations are single-phase 220 VAC up to 400 Hz and 28 VDC.
-
Product
Planar-Doped Barrier Diode Detector, 0.01 to 50 GHz
8474E
Diode Detector
The Keysight 8474E is a high-performance detector using a gallium arsenide, planar-doped barrier detecting element. It features extremely flat frequency response over its entire band of operation and very good frequency response stability versus temperature. The Keysight 8474E is also very rugged with high resistance to ESD damage. The Keysight 8474E detector is available with a 2.4-mm (0.01 to 50 GHz) connector. This detector offers the options for optimal square-law loads (Option 102) and for positive polarity output (Option 103). Because the unit-to-unit frequency response tracking of this device is typically better than plus or minus 0.3 dB, no matched response option is offered.
-
Product
Laser Power and Targeting
ST60 Quad
-
A four-channel silicon-based thermopile detector in a TO-5 package. Each small active area size is 0.61mm x 0.61mm. This is our lowest-cost and fastest time constant four-channel detector. It delivers a time constant of 18ms with Nitrogen encapsulation gas combined with a very low Temperature Coefficient of Responsivity of -0.04%/C. This detector has a very short thermal shock response to ambient temperature change.
-
Product
PXI Resistor Module 4-Channel 1R to 255R
40-293-013
Programmable Resistor Module
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Low-Dropout Regulators
-
Renesas is a leading low-dropout regulator (LDO) supplier in low power handheld applications with world-class differentiated single and dual LDOs which have ultra-high PSRR up to 3MHz, low input voltage range, tiny packages, and ultra-low noise and quiescent current. Renesas' high current LDOs support up to 3A and have industry-leading fast load transient response, tightest voltage output accuracy at full load and over the full junction temperature, and lowest dropout voltage in its class.
-
Product
Precision Current Sources
-
HighFinesse Precision Current Sources have been developed for experiments and quantum technologies in the areas of cold-atom and solid state physics. The linearly regulated BCS (Bipolar Current Source) and UCS (Unipolar Current Source) series deliver highly stable, low noise source currents for high precision magnetic field control. The current output is floating or is on a used defined potential. Ultrafast response to control signals and trigger functions, clear grounding, connection and signal isolation schemes make the integration of the current sources into complex experimental systems easy.
-
Product
Type 2, PCMCIA Dual Redundant MIL-STD-1553 serial bus Simulator Analyzer Tester
PC401
-
MIL-STD-1553 A, B, & McAir MULTI PROTOCOLS Simulator/Analyzer/Tester type 2 PCMCIA BUS Interface Card - The PC401 can be used for Validation Testing, ProductionTesting, full bus simulation and monitoring, as a generalpurpose 1553 interface or a stand alone bus Analyzer. Forprecise message scheduling and measurements, the Majorand minor frame times are independent of messagesequences or retransmissions on errors and the start of allcommand messages are independent of message length,response time or length of response. Message timing iscalibrated and RT responses have low jitter.
-
Product
Fast Response Flow Controller for Low Flow
HFM-300 / HFC-302
-
The all metal HFM-300/HFC-302 is Teledyne Hastings' metal sealed, fast response series of mass flow meters and controllers. Featuring reliability and stability, the 300 Series is chosen by OEM's for its fast response under a wide range of conditions.The HFM-300 / HFC-302 meters and controllers have flow ranges from 0-5 sccm to flows of 0-25 slm; provide analog outputs, are constructed of stainless steel and have normally closed valves. The full scale range is specified by the end user. A NIST traceable calibration certificate is standard. Corrosive gases and pressures up to 1000 psig are easily measured. Cleaning for oxygen service is available.
-
Product
DC Power Supplies
SG Series
-
AMETEK Programmable Power, Inc.
The Sorensen SG Series (hereafter SG Series) represents the next generation of high power programmable DC power supplies. The SG Series is designed for exceptional load transient response, low noise and the highest power density in the industry. With a full 15 kW available down to 20VDC output in a 3U package the SG Series leads the industry in power density. The power density is enhanced by a stylish front air intake allowing supplies to be stacked without any required clearance between units.
-
Product
K Thermocouple Surface Probe
TP777
-
Surface thermocouple Type "K" probe. °C max: 200. Response time: 3 s.
-
Product
Luminance Probe
LP471LUM2
-
Photometric probe for measuring the LUMINANCE, spectral response according to the photopic curve, angular field 2°.
-
Product
Accelerometers
-
Columbia Research Laboratories
The force balance accelerometer has a classical critically-damped, second-order frequency response. There is no peaking in the response but simply a smooth roll-off above the natural frequency. This property along with the excellent characteristics of the "HP" torquer design makes Columbia accelerometers the best choice for demanding applications where precise DC and near-DC measurements are needed in demanding shock and wide band vibration environments. Columbia force balance accelerometers are available to cover virtually all applications. Low noise, high output units can be used for seismic structure motion studies while miniature, high range versions are optimum for measuring more violent high G environments encountered in many industrial, aircraft and missile applications.
-
Product
- RS-422/485 DIN Rail Mounted Lightning/Surge Protector
Model 8022NX
-
FEATURES: Fast Response; Automatic Recovery; Up To 20 MBPS Data Rate; DIN Rail Mounted; Full Duplex; Triple Stage Protection. The Model 8022NX is a DIN Rail mounted surge suppressor for 4-wire RS-422 or RS-485 circuits used to protect factory data networks, or, any network that wants to avail itself of the DIN Rail packaging concept. The Model 8022NX provides common-mode (line to ground) surge protection and differential mode (line to line) protection for balanced networks. All the inputs, outputs and ground connections are via screw terminals located on the top surface of the device.
-
Product
CXA Signal Analyzer, Multi-touch, 9 kHz to 26.5 GHz
N9000B
Signal Analyzer
Master the essentials in signal characterization with the leading low-cost tool in signal analysis Perform cost-effective stimulus response measurements with the optional built-in tracking generator Add crucial functionality with X-Series measurement applications Enhance theory with practical skills when used with a training kit in your RF & microwave education lab
-
Product
Non-functional Testing Services
-
Good software has both- efficient functionality and excellent performance. While functional testing pays attention to improve the functioning of the software, our non-functional testing solutions aids in enhancing software performance under various conditions. QACraft has helped several enterprises all over the globe to boost performance by evaluating the software when it comes to software and eradicating the lacking factors from it. Carrying out non-functional testing for the software helps in checking the software’s accessibility, scalability, and responsiveness.
-
Product
Micro Capacity Type High-Speed Rotation Torque Detector
TH-3000/3000H Series
-
TH-3000 series is a torque detector designed for very low torque (less than 2 N· m) with high response and high accuracy. Two types are available depending on your applications.
-
Product
Energy Probes
RjP-400 Series
-
The RkP-400 Series probes consist of a compact detector assembly, or head, and a preamplifier housed in a separate enclosure. The external dimensions of all the 400 Series Probes are the same, with identical detector planes, allowing for easy interchange of probes in an experiment. The heads have both ¼-20 and M6 tapped holes, a built-in 1" (25mm) filter holder, and a side-mounted BNC connector. Probe specific data, including spectral response curves and calibration dates, is stored in the preamplifier for access by the instruments.
-
Product
SC-1 Monitor
CS-131
-
The CS-131 is a high-precision chemical concentration monitor designed for use with SC-1 solutions used in cleaning processes during semiconductor manufacturing. It offers a faster response speed in a more compact size than anything available to date. The CS-131 monitors the concentrations of the individual components of the SC-1 solutions (NH3/H2O2/H2O) which is widely used to remove particles and organic substances. The monitor has a number of outputs which can be utilized to keep the concentrations of the individual elements of the SC-1 solutions within the allowable ranges; this eliminates unnecessary replacement of chemicals potentially increasing bath life time and reducing chemical cost. In addition, a model with an integrated cooling unit is available, allowing accommodation of a broader range of sample temperatures.
-
Product
Hydrophone
RESON TC 4038
-
The TC4038 is a miniature probe hydrophone, specifically designed as a standard reference hydrophone for high frequencies in the range: 100kHz to 1.2MHz. The TC4038 provides a flat frequency response and omnidirectional characteristics in the specified frequency range. The sensor element has excellent stability, which ensures reliable sensitivity over long periods of time.
