High Frequency
High Frequency operating at 3–30 MHz.
-
Product
Noise Source, 1 GHz up to 50 GHz
346CK01
Noise Source
The Keysight 346CK01 is the ideal companion to Keysight´s noise figure solutions when working on high frequency applications. Since it is broadband (1 GHz to 50 GHz), it eliminates the necessity for several sources at different frequency bands. The low SWR of the noise source reduces a major source of measurement uncertainty, which are reflections of the test signals. This is a coaxial noise source with a 2.4 mm coaxial connector. ENR typically 20 dB at 1 GHz, decreasing to typically 7 dB at 50 GHz.
-
Product
PCIe Digital I/O Board, 64 Optically Isolated I/O Channels, 24V
APCIE-1564
-
32 digital inputs, 24 V, isolated16 interruptible inputs32 digital outputs, 24 V, isolated, 10 to 36 V, 500 mA/channelOptical isolation 1000 VWatchdog for resetting the outputs to "0" (when Power-On)Protection against fast transients, overvoltage, electrostatic discharge and high-frequency EMIInputs: voltage reversal, input filtersOutputs protected against short circuitOvertemperature and overvoltage protectionDiagnostic report in case of short circuits, overtemperature, voltage drop ...24 V power outputs with protection diodesShutdown logic when the external supply voltage drops below 5 V
-
Product
16-bit, 200KHz, 8SE/4DIFF Isolated AI, 4 12-bit AO, 8 Optically Isolated Dig. I/O, 24V, 24 TTL I/O
APCI-3116-8
-
The APCI-3116 is a 16-bit multifunction board for 3.3 V and 5 V PCI systems, with optical isolation up to 1000 V and a high throughput rate of 200 kHz. The PCI board has additional types of conversion: Sequence RAM, Auto Refresh, scan, timer or external event.Furthermore, the board has a PCI DMA, 2 watchdogs, 4 digital inputs and 4 digital outputs. Sensors, which allow to supply current signals instead of voltage signals, also can be acquired with the APCI-3116, as this board offers up to 16 current inputs. The board is protected against overvoltage and input filter and it is protected against high frequency emmission. With the free calibration tool you can do the fine adjustment on-site.
-
Product
Voltage Meter
MN3I
-
М-module МН3И is a mezzanine module designed to measure the instantaneous voltage value of high-frequency signals via 3 galvanically isolated channels from each other, control circuits and crate frame.
-
Product
Maritime Navigation and Communications Antennas
-
LBA provides equipment and services to support shore station requirements for modern maritime communications in the low frequency, medium frequency, and high frequency radio bands
-
Product
Universal Preamplifier 14
UP14
-
For Two Dimensional Magnetic Recording (TDMR) and Heat-assisted Magnetic Recording (HAMR) Headamplifiers. Universal Preamplifier 14 (UP14) is designed for TDMR and HAMR Head Amplifiers. With new Guzik RWA4000 TDMR, UP14 allows to process signals from three Read Channels. It also supports two high speed data channels for Write data and Laser data. UP14 has two channels for dynamic TFC control and allows to program TFC power per sector and close loop TFC power control in each channel. UP14 can generate two programmable modulation signals for write data and laser data with bandwidth up to 20 MHz. UP14 consist of two boards. The first UP14 RW Board processes high-frequency signals: read-back signals, write data and laser data. The second UP14 Control Board provides power, control and low-frequency signal generation: TFC, write data modulation and laser modulation.
-
Product
Oil Resistivity Test System / Million Meg Ohm Meter (MM1)
OTD-45
-
UDEYRAJ ELECTRICALS PRIVATE LIMITED
Model : OTD-45OTD-45 is single self contained unit containing oil test cell, high frequency induction heating with temperature controller/sensor; dielectric loss measuring bridge, AC test voltage source, SF6 filled standard capacitor; high resistance meter; DC voltage source and all digital circuits.
-
Product
High Impedance Active Probes
28 AND 29
-
Designed to serve the needs of integrated circuit engineers working in the most advanced high speed, submicron, MOS technology. These high frequency instruments include the attractive features of the Models 18C and 19 including full dc capability, negligible dc current drain, and extremely low input capacitance. In addition the frequency range of the Models 28 and 29 has been extended to a full 1 GHz.
-
Product
AC Current Transformers
-
CR Magnetics supplies an extensive line of toroidal current transformers for any need. Our offerings include measuring from 10,000 amps to a few milliamps. This includes ANSI, Commercial, Ground Fault, High Frequency, Wound Primary, DC Immune and Nano Alloy current transformers.
-
Product
Electronic Components Test
-
Parameters to be measured (absolute value): Measure hypo-class U, Iout, Hz, Hc, Br, Bm, Hm, Br /Bm, m, magnetic core loss, B-H curve, U curve and I curve Output capacity of the high frequency power: Uout: 1~300V, Iout: 0.05~5A, Pout: 300VA, frequency: 10~300kHz Accuracy: 2% With 12-bit high-speed A/D, sampling rate up to 40MHz, ensuring data precise and stable test result Supermaximal database, suitable for almost all kinds of magnetic material in market, such as: circle, E ,U , ETD-EER, JAR, RM , EP , PM , EL , ER, PQ, EFD, plane E, etc Perfect software interface enables observation of curve in detail Meet international test requirements for magnetic particle ASTM E1444, ASTM E709-08.
-
Product
Flaw Detectors
-
GAOTek flaw detectors are designed as high-quality devices that provide accurate detection whilst delivering ease of use towards testing and monitoring. These detectors examine a material by passing sound waves at high frequencies through it and are used for applications that require ultrasonic testing. They are compact, easy to carry and portable devices that allow the user to work in complex conditions and circumstances, and available for purchase in the United States, Canada and globally.
-
Product
Analog AC Leakage Current Clamp Tester
MCL-350
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*High accuracy analog display with strong taut band meter.*3 years long battery life.*Meter lock function and data output for recorder.*Filter rejection for high frequency noise
-
Product
Basic Unit - Medical Equipment Functional Test Module System
GS-X
-
The GS-X Testing System consists of a Basic Unit and various plug-in test modules which the user can purchase as required. The range of functions of these Module-Box is being continuously expanded, and presently includes functions for testing the following devices: - Infusion pumps, Cardiac pacemakers, Defibrillators, High-frequency Surgical equipment, electrical safety ECG Simulation, Equipment for electro-stimulation.
-
Product
Thin-Type Ionizers
ER-VW Series
-
Panasonic Industrial Devices Sales Company of America
The Panasonic ER-VW Thin-Type Ionizer uses high frequency AC in an ultra-thin Ionizer for superior static elimination.
-
Product
DC TO 40 GHz
MDHC Series
-
Smiths Interconnect's spring loaded High Frequency Micro-D Coax Connectors MDHC offer low VSWR of 1.5:1 (typical) up to 40GHz (max mated pair), maximum overall diameter of 0.125" fitted into low-profile micro-D housing, constant 50 Ohm airline impedance.
-
Product
High Frequency Multipin Coax Connectors
MDCX Series
-
Smiths Interconnect's multipin coax connectors MDCX offer low VSWR of 1.25:1 (typ) up to 10 GHz (max mated pair), maximum overall diameter of 0.125" fitted into low-profile micro-D housing, constant 50 Ohm airline impedance.
-
Product
High-Frequency Probe, 300 kHz to 3 GHz
85024A
ICT/FCT Probe
85024A high-frequency probe makes it easy to perform in-circuit measurements. An input capacitance of only 0.7 pF shunted by 1 megohm of resistance permits high frequency probing without adversely loading the circuit under test. Excellent frequency response and unity gain guarantee high accuracy in swept measurements with this probe. High probe sensitivity and low distortion levels allow measurements to be made while taking advantage of the full dynamic range of RF analyzers.
-
Product
1 GHz, 1 MΩ, 0.9 pF Active Probe
ZS1000
-
Engineers must commonly probe high frequency signals with high signal fidelity. Typical passive probes with high input R and C provide good response at lower frequencies, but inappropriately load the circuit, and distort signals, at higher frequencies. The ZS Series features both high input R (1 MΩ) and low input C (0.9 pF) to reduce circuit Loading across the entire probe/oscilloscope bandwidth. The ZS1000 is ideal for 200–600 MHz oscilloscopes.
-
Product
RFID
HF (13.56 MHz)
-
BIS M uses the high frequency (HF) 13.56 MHz and supports the standard according to DIN ISO 15693 and 14443. Communication modules/gateways are used for the point-to-point or bus linking and are directly connected to a serial interface of a PC/a bus interface. The Subnet16 TM bus architecture supports a subnet of up to sixteen nodes via an RS485 interface.
-
Product
Signal Generator Extension Modules
SGX
-
Virginia Diodes, Inc. (VDI) Signal Generator Extension (SGX) modules provide high performance frequency extension of microwave signal generators into the THz range. VDI SGX modules offer full waveguide band coverage and are available from WR15 (50 to 75 GHz) to WR1.0 (750 to 1100 GHz) with additional bands under development. This turn-key, sweepable solution is compatible with any microwave signal generator that meets the input frequency and power requirements.
-
Product
RF Coaxial Connectors
-
Radiall is proud to offer the widest range of RF coaxial connectors in the industry. We offer over 13,000 part numbers and 55 product series including AEP® and Mil QPL connectors. Radiall started by manufacturing coaxial cables and connectors; now, more than 60 years later, these precision-made components are still a primary focus of our business. We design and manufacture RF coaxial connectors for a wide variety of industries. Our offerings include coax connectors that are waterproof, high frequency, snap-on, non-magnetic and more. We will also design custom connectors for your specific application.
-
Product
Board-to-FPC Connector for 5G Millimeter-Wave Antenna Modules
-
Panasonic Industrial Devices Sales Company of America
Panasonic's Board-To-FPC Connector for 5G Millimeter-Wave Antenna Modules offer good SI/EMI/EMS characteristics for high-frequency applications and features our industry-leading Tough Contact construction that achieves high contact reliability and retention force. Tough against shock impact by misalignment, the fully-shielded structure in both socket and header significantly improves EMI characteristics necessary for RF applications such as 5G.
-
Product
Intelligent identification
RFID
-
Radio-based RFID technologies in the HF (high frequency) and UHF (ultra high frequency) ranges supplement SICK’s industrial automation portfolio. In applications where process-relevant data is modified remotely, RFID makes it possible to store data on writable and rewritable media. And, in contrast to optical solutions, RFID provides reliable identification of all objects – despite dirt and everyday wear.
-
Product
Mini Receiver
FB7-NX
-
In about 1935, the National Radio Company of Malden, Mass., brought out a “hot” high frequency receiver, called the FB7, and the subsequent FB-7X. It featured a super-hetrodyne design with plug-in coils that gave it a broad frequency range. The “X” model also incorporated a crystal filter in the intermediate frequency section, thus giving it additional selectivity. The receiver was viewed by radio amateurs as a technological breakthrough, and it was also used commercially for point to point high frequency communications. As the receiver did not have an internal RF amplifier section, a separately tunable RF amplifier was later provided in a separate enclosure for additional performance capabilities. Now, National RF, Inc., is resurrecting the fabled receiver name with an all solid-state, hot mini receiver, which also utilizes plug-in coils to cover the HF spectrum. The mini-receiver is designed for use by radio amateurs as well as serious short-wave listeners, and allows reception of AM, CW, and SSB signals. It incorporates a super-hetrodyne design with a dual gate FET built-in RF preamplifier and a ceramic filter for selectivity, often required when used in a crowded amateur radio band. In addition, the receiver has a buffered rear panel output of the high frequency oscillator for use with either a frequency counter for exact receive frequency display, or for interface with an outboard transmitter. A rear panel jack is also provided for muting the receiver when a transmitter is placed into the transmit mode. And, the receiver is small enough to fit into carry-on luggage and taken on trips when it is desired to “keep an ear” on amateur radio or other high frequency activity. The receiver utilizes rear panel plug-in coil assemblies which contain the RF amplifier, mixer, and oscillator tuned circuits. Each plug-in coil assembly also comes with a separate dial scale, which is inserted onto the front panel for displaying the tuned frequency. A very smooth 6 to 1 planetary drive is used for tuning the receiver. Other front panel controls include RF preamplifier peak, volume control, Beat Frequency Oscillator adjustment, and RF gain control. Other switches include filter bandwidth, AM/CW/SSB selection, Power, and a general coverage/band spread control for certain plug-in assemblies. The receiver is intended to drive head-phones via a rear panel jack, but has sufficient output to drive a small external speaker.
-
Product
Artificial Power Supply Network
KH3763
-
Beijing KeHuan Century EMC Technology Co,.LTD
The artificial power supply network (also called the power supply impedance stabilization network) should be able to provide a stable impedance to the device under test in the radio frequency range, isolate the device under test from high-frequency interference on the power grid, and then couple the interference voltage to the receiver.
-
Product
RF Cable Assemblies
-
Radiall's extensive range of RF cable assemblies features outstanding electrical performance, low loss and high frequency. The range includes flexible, semi-rigid, corrugated and hand-formable cable assemblies with a combination of RF cables and connectors optimized for each market or application. Custom RF cable assemblies are also available.
-
Product
ATE Connecting Solutions
-
C.C.P. Contact Probes Co., LTD.
Customized pogo towers with high frequency capability.
-
Product
Inductive Sensors
-
Inductive Proximity Switches, self contained, depend on the output of an oscillator for their operation. The oscillator resonant circuit uses an open core coil to produce a concentrated high frequency electromagnetic (RF) field, which emerges from the active surface of the sensor. If a metal target (or other electrically conductive material) enters this field, eddy currents will be induced in it, causing the resonating oscillator to be damped.
-
Product
Passive Probe, 10:1, 150 MHz, 1.2 M
N2841A
Oscilloscope Probe
The Keysight N2841A low-cost passive probe provides a 10:1 attenuation and features a high input resistance of 10 MΩ. The probe can be adjusted for low-frequency compensation and high-frequency compensation.
-
Product
High Frequency LCR Meters up to 30MHz
11050
-
Chroma Systems Solutions, Inc.
The Chroma 11050 Series HF LCR Meter is a precision test instrument designed to accurately measure and evaluate passive components at high speeds. Its measurement capabilities cover the primary and secondary parameters required for testing the inductance, capacitance, resistance, quality factor and loss factor of passive components. The HF LCR Meter has a broad testing frequency range 75kHz~30MHz/1kHz~10 MHz/60Hz~5MHz suitable for analyzing component characteristics under different frequencies. Its 0.1% basic measurement accuracy provides stable and highly reliable results. A fast 7ms measurement speed effectively increases productivity when working in an automated environment.
