High Frequency
High Frequency operating at 3–30 MHz.
-
Product
Chip Inductors-Multilayer
-
Bourns Miltilayer chip inductors offer high frequency, nickel barrier, monolithic construction for high reliability, and magnetically shielded construction providing low radiation. They are well-suited for DC-DC converters, and prevention of electromagnetic interference to signals on the secondary side of electronic equipment, among many applications.
-
Product
High-Frequency Test Coil
-
West Coast Custom Designs, LLC
is most commonly used by the neon industry for detecting leaks in a pumping system; the spark generated by the coil via the solid tip, will enter the tube through the leak and become bright white at the point at which it enters.
-
Product
Blocking Capacitor, 0.045 to 26.5 GHz
11742A
-
The Keysight 11742A blocking capacitor blocks dc signals below 45 MHz and passes signals up to 26.5 GHz. Ideal for use with high-frequency oscilloscopes or in biased microwave circuits, the Keysight 11742A will suppress low frequency signals that can damage expensive measuring equipment or affect the accuracy of your RF and microwave measurements.
-
Product
RF & Microwave Test Cables
-
Rosenberger Hochfrequenztechnik GmbH & Co. KG
VNA Test Cables and microwave cable assemblies (RF Coax cable assemblies) must have a high degree of mechanical flexibility in combination with constant electrical stabilities. Such cables are usually used in laboratories for high-frequency measuring applications and test stations, as well as in the areas of telecommunications, automotive, medicine, industry, consumer electronics and aerospace for signal transmission and other applications.
-
Product
1.5 GHz, 1 MΩ, 0.9 pF Active Probe
ZS1500
-
Engineers must commonly probe high frequency signals with high signal fidelity. Typical passive probes with high input R and C provide good response at lower frequencies, but inappropriately load the circuit, and distort signals, at higher frequencies. The ZS Series features both high input R (1 MΩ) and low input C (0.9 pF) to reduce circuit Loading across the entire probe/oscilloscope bandwidth. The ZS1500 is ideal for 1 GHz and lower oscilloscopes.
-
Product
Event Based Image Sensors
EVS
-
Event-based Vision Sensors (EVS) help alleviate this issue by only sending data from pixels who have detected a change in intensity. This allows them to minimize the volume of data that is transmitted over the sensor’s data bus while minimizing the processing resources need to analyze the image. On top of this, individual pixel autonomously responds to illuminance changes allowing the sensor to detect small and/or high frequency changes with lower bandwidth requirements.
-
Product
Artificial Power Supply Network
KH3762
-
Beijing KeHuan Century EMC Technology Co,.LTD
The artificial power supply network (also called the power supply impedance stabilization network) should be able to provide a stable impedance to the device under test in the radio frequency range, isolate the device under test from high-frequency interference on the power grid, and then couple the interference voltage to the receiver.
-
Product
0.5-2.4GHz Instantaneous Frequency Measurement Unit
DR063-M2
-
Teledyne Defence & Space’s Instantaneous Frequency Measurement (IFM) module, also known as a Digital Frequency Discriminator (DFD), offers high speed frequency measurement across the full operating bandwidth.The IFM measures the frequency of RF signal present at its input and presents a result at its output as digital data. The RF input signal is conditioned by an RF amplifier that provides sufficient drive for the frequency resolving circuits. The raw video from the resolvers is digitised and processed into the required output format. There is additional timing and control circuitry which initiates the measurement process and provides handshake data to the host system processor.
-
Product
EMC Testing
-
D.L.S. Electronic Systems, Inc
EMC testing and consulting services to the Electronics, Medical Equipment, Automotive, Aerospace, Computer, Telecommunications, and other industries. We are a NVLAP certified test facility, capable of testing electronic equipment to today's high frequency requirements. Our 14 Test chambers and 3 Open Area Test Sites can perform full scan Immunity and Emission testing at frequencies up to 40 GHz. Please contact us for your specific requirements.
-
Product
Vehicular Antennas
-
Pulse manufactures a diverse line of outdoor automotive antennas. Our ruggedized, built- to-last antennas cover frequencies 136 MHz to 6 GHz, including GNSS and multi-band antennas. Most antennas are available in a variety of mounting styles including NMO, direct mount, glass, and magnetic mounts, and in many different form factors such as low profile, stealth blade, low profile transit, and whips. Pair your vehicular antenna with our wide variety of high performance, high frequency NMO Mounts making your vehicular installation easier while also insuring the best possible antenna performance. Pulse is a leader in automotive aftermarket antennas and has been a main supplier to large Automotive OEM’s for decades. Find your next automotive antenna and NMO Mount today using the product finder below.
-
Product
Advanced Design System (ADS) Core
W2200BP
-
Advanced Design System (ADS) is the flagship product from Keysight EEsof EDA, the technology and innovation leader in high-frequency, mixed-signal electronic design automation (EDA). It is the only design simulation platform that enables the co-design of IC, package and board in high-frequency and hi-speed applications. ADS seamlessly integrates system, circuit, and full 3D electromagnetic simulation with Keysight's test instrumentation to perform single pass successful electronic designs repeatedly.
-
Product
SMT & QFN Products
-
PMI offers custom surface mount (SMT) and QFN packaging for many types of devices. SDLVA's, Log Amplifiers, Phase Shifters, Attenuators, Switches, as well as Low Noise Amplifiers. PMI also offers multifunction options in a single QFN package such as Limiter / LNA or LNA / Detector. PMI has the experience to offer custom devices that meet your specific control function at high frequency. Mounting and integrating high frequency RF devices take skill and experience such that the package itself does not degrade the RF signal. PMI has the experience in selecting the proper package, integrating the RF devices and providing the required testing.
-
Product
Chip-Type Attenuators
-
Panasonic Industrial Devices Sales Company of America
Chip-Type Attenuators for high-frequency signal attenuation, level adjustment or matching improvement.
-
Product
IR Carbon and Sulphur Analyzer
LD-LCSA-A10
-
IR Carbon and Sulphur Analyzer LD-LCSA-A10 is a unit for determination of sulphur and carbon equipped with two treatment units including a high frequency induction burner and flexible temperature settings with automatic control. With an analysis time of 20 to 100 seconds and a sensitivity of 0.1 ppm the multi-shielded isolation circuit prevents the machine for high frequency interference. High speed 24-bit sampling improves sensitivity and accuracy.
-
Product
Track and Hold Data
-
Track and hold amplifiers are used to expand the bandwidth and/or high-frequency linearity of high-speed A/D conversion and signal acquisition systems. Track and Hold Amplifiers can be used in various applications including RF ATE Applications, Digital Sampling Oscilloscopes, RF Demodulation Systems, Digital Receiver Systems, High Speed Peak Detectors, Software Defined Radio, Radar, ECM & ELINT Systems and High Speed DAC De-Glitching.
-
Product
PCIe High-Speed Digitizer
U5310A
-
The U5310A is a two channel PCIe, DC coupled 10-bit signal acquisition card providing sample rates up to 10 GS/s with 2.5 GHz bandwidth for use in a variety of advanced imaging and processing systems. Featuring unique spurious-free dynamic range (SFDR) and signal-to-noise ratio (SNR) performances in high frequencies, especially at 250 mV full scale range (FSR), the U5310A ADC card is suited for embedded OEM applications requiring signal acquisition at wide bandwidth and high dynamic range.
-
Product
Electromagnetic Resonance High Frequency Fatigue Testing Machine
PLG Series
-
Jinan Testing Equipment IE Corporation
The series of electromagnetic resonance fatigue testing machines are used for fatigue tests of metal materials and components under tension, compression or reversal loads. If relevant grips are provided, three-point bending test, four-point and circle test, gear wheat, bolt, connecting rod, roller chain, crackle expanding test can be available. The series of electromagnetic resonance fatigue testing machines feature an optimized design and a rational structure. The automatic controlled system adopts an advanced and wide-pulse-control system and a new-type of power amplifier to improve the reliability of the electric system. The electromagnetic resonance fatigue testing system is with high efficiency, easy and non-stop shake, low energy consuming, accurate control, and small fluctuation.
-
Product
Low-Noise Amplifiers
-
Broadband, narrowband, high-frequency, our extensive portfolio of LNAs is ready to tackle the toughest requirements. Don’t see exactly what you need? We have a vast library of pre-engineered building blocks ready to support any custom design.
-
Product
AC / DC Combined High Voltage Test Set
-
Cambridge Instruments & Engineering Co.
suitable to perform AC High Voltage Power Frequency test on transformers, motors, cables etc. Leakage current can be measured at desired pressure and this set can be used as a source for cable fault burning.
-
Product
Differential Probe
DP-60HS
-
*High Sensitivity Model: x 1, x 5, x 10 Attenuation*1 MΩ // 10PF Input Impedance*High Frequency Operation: x 1(30 MHZ), x 5(60 MHZ), x 10(60 MHz)*Especially For Low Voltage: x 1(7 Vp-p), x 5(35 Vp-p), x 10(70 Vp-p)
-
Product
Switches
-
Whether you are performing high-accuracy, low-speed measurements on a dozen test points or high-channel, high-frequency characterizations of integrated circuits, National Instruments delivers a flexible, modular switching solution based on PXI or SCXI to help you maximize equipment reuse, test throughput, and system scalability.
-
Product
Frequency Divider
Trig-TekTM 313A
-
Divide high frequency to a lower frequency with an exact integer division with 1-digit divisor increments from 1 to 9999
-
Product
RF Test Solutions
-
Peritec is accredited by the "RF and Wireless Specialty" (radio expertise and RF) from National Instruments (NI).The RF and Wireless Specialty, NI Alliance partners with expertise specialized design of radio frequency / wireless, authentication, automatic test, the high-frequency measurement is certified. Based on the track record and a wealth of expertise, Peritec, offers test solutions for RF / Wireless system.
-
Product
High-Frequency Probe, 300 kHz to 3 GHz
85024A
ICT/FCT Probe
85024A high-frequency probe makes it easy to perform in-circuit measurements. An input capacitance of only 0.7 pF shunted by 1 megohm of resistance permits high frequency probing without adversely loading the circuit under test. Excellent frequency response and unity gain guarantee high accuracy in swept measurements with this probe. High probe sensitivity and low distortion levels allow measurements to be made while taking advantage of the full dynamic range of RF analyzers.
-
Product
Signal Analysis
Super-Resolution Spectrum
-
Super-resolution Spectrum is used for spectral signal analysis with high frequency resolution. The program is used in diagnostics and monitoring systems of buildings and for analyzing non-stationary signals. The Software enables solving the following tasks:
-
Product
VME 32X 5 Slot 6U
-
ANSI/VITAV 1-1994 VME32 Backplane, 6U 5 Slot Including J1 & J2.Benefits:• Standard VME backplanes are available also in other slot count configurations• Surface Mount Technology – Excellent high frequency performance, high reliability and reduced cost due to SMT
-
Product
Servo And VFD Filters
-
Operation of PWM-driven motors – servo motors and variable frequency drives (VFD) – causes several problems in equipment, including damage to the motor’s bearings due to leakage current causing electrical discharge machining (EDM) and damage to motor’s insulation. PWM motors also are a major source of EMI in equipment. These motor drive systems use pulsed power to drive the motors. As we are aware, the sharp edges of the pulses inevitably include high frequency components which can couple or radiate as noise to other parts of your system and cause unreliability, communication/control problems and EMC compliance issues.
-
Product
High Frequency Connectors
-
C.C.P. Contact Probes Co., LTD.
CCP is an expert in the design of high frequency connectors. We offer 5G ready connectors and USB 3.2 connectors.
-
Product
Analog Ultrasonic Inspection System
ULTRAPROBE 100
-
The Ultraprobe senses high frequency sounds produced by operating equipment, leaks and electrical discharges. It electronically translates these signals by heterodyning them down into the audible range so that a user can hear these sounds through a headset and see them as intensity increments on the meter. Heterodyning works the same as a radio in that it accurately transforms the sounds so that they are easily recognized and understood.
-
Product
DC - 12 GHz High Efficiency GaAs HBT MMIC Divide by 8 Prescaler
HMMC-3028
-
The HMMC-3028 is a DC - 12 GHz divide by eight prescaler designed for use in high frequency communications, microwave instrumentation, and EW radar systems where low phase-noise PLL control circuitry or broadband frequency translation is required.
