-
Product
Load Pins
-
When overload protection and/or load indication is to be installed in a conveyor, crane or other device, the PIAB SLC is the ideal solution. The PIAB SLC Load Pin easily replaces the existing shaft at an equalizing pulley or in other parts of the construction. The PIAB SLC Load Pin should be installed as close as possible to the force/load for best accuracy. Both the PIAB SLC Load Pin and the PIAB LCA Amplifier are designed to withstand extreme environmental conditions for a long operation time.
-
Product
37 Pin Breakout Interface
VSI-Breakout-37
-
The VSI-Breakout-37 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
Product
Connector, PCB Mount, 25 Pin 1.27mm Pitch Micro-D, Male, Straight
C025CMX-1PS-0A
-
This 25 pin micro-D straight connector is designed to allow users to create their own PCB based connection solution. Screwlocks are provided to secure the connector to its associated cable assembly. This connector is suitable for high density applications including connection to Pickering's LXI DIO/Trigger port via a suitable cable
-
Product
Pin Pointer
CFL PP3+
-
The new generation CFL PP3+ Cable Fault Pin Pointer cum route tracer from SCOPE is the ultimate solution for locating of underground cable faults in minimum time by tracing cable route. It uses an advanced technology which helps even an unskilled operator to locate the fault accurately.
-
-
Product
Cable Assembly, 50-Pin D-Type, Female to Unterminated With Tinned Ends, 2m HV, Exit Towards Pin 1
A050DF5-T-HA200
-
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
25 Pin D-Type Connector Blocks For Pickering Products
-
The connector blocks below are suitable to use with Pickering cards and modules that utilize a 25-pin D-type connector.
-
Product
44 Pin D-Type Cables - 44 Pin To Alternative Connector For Pickering Products
-
High-density, 3-row, 3A-rated, 250VAC-capable connector assemblies used primarily for interfacing PXI, LXI, or PCI switching modules.
-
Product
Signal, Contact, ITA, QuadraPaddle, Male PCB Pin
610138123
-
Signal, Contact, ITA, QuadraPaddle, Male PCB Pin.
-
Product
44 Pin D-Type Connectors For Pickering Products
-
The connectors below are suitable to use with Pickering cards and modules that utilize a 44-pin D-type connector.
-
Product
Load Pins, Tension Load Links, And Load Shackles
-
Interface’s wide range of load pins are designed for the measurement of tensile and compressive forces across a wide variety of applications, including crane/lifting, industrial, marine, offshore, and civil engineering. Machined from high tensile stainless steel, our load pins are suitable for use in exposed situations including prolonged immersion in seawater. Interface’s tension load links are designed for lifting and weighing applications in harsh environments and manufactured from high tensile aluminum and stainless steel. Interface’s load shackles are manufactured from high tensile carbon steel and the basic shackle uses the renowned Crosby G2130, G2140, and G2150 series (depending on the load rating).
-
Product
Cable Assembly, Receiver, 36", QuadraPaddle, 50 Pin FML D-Sub
540111020240
-
Cable Assembly, Receiver, 36", QuadraPaddle, 50 Pin FML D-Sub.
-
Product
Additional Products: 500 Pin SEARAY Cables - Connector to Unterminated
-
The connector to unterminated cable assemblies below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
Product
Cable Assembly, Receiver, 36", QuadraPaddle, 160 Pin Female DIN
540069010229
-
Cable Assembly, Receiver, 36", QuadraPaddle, 160 Pin Female DIN.
-
Product
500 Pin SEARAY Cables - Connector to Unterminated For Pickering Products
-
The connector to unterminated cable assemblies below are suitable to use with Pickering cards and modules that utilize a 500-pin SEARAY (250-port) connector.
-
Product
Additional Products: 78 Pin D-Type Connectors
-
The connectors below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
Product
50 Pin Breakout Interface
VSI-Breakout-50
-
The VSI-Breakout-50 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
Product
Cable Assembly, Receiver, TriPaddle, 20", 200 Pin Male LFH with M3 Jackscrews
540105020105
-
Cable Assembly, Receiver, TriPaddle, 20", 200-Pin Male LFH with M3 Jackscrews
-
Product
Additional Products: 100 Pin 1.27mm Pitch Micro-D Cables - 100 Pin To Alternative Connector
-
The connector to connector cable assemblies below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
Product
Cable Assembly, 50-Pin D-Type, Female to Unterminated With Tinned Ends, 2m HV, Exit Away From Pin 1
A050DF4-T-HA200
-
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
4 Pin Power D-Type Female Connector, 40A, PCB Mount
40-963-004-RF
-
This connector is suitable for Pickering Interface's modules that use the 4-Pin Power D-Type connector. It is designed to allow users to make a termination via a PCB.
-
Product
Pin Type Moisture Meter
2019
-
Peaceful Thriving Enterprise Co Ltd
To measure fiber substance, building & constructing materials, various nonmetallic material, paper, wood, bamboo products, Chinese medicinal herb, tobacco, cotton, textile, soil and so on.
-
Product
50 Pin IDC Cables - 50 Pin Connector To Unterminated
-
50-pin IDC cables (2x25 matrix, 2.54mm pitch) connect to SCSI, I/O racks, or PCB boards, with one end featuring a female/male IDC connector and the other being unterminated (bare wire or tinned) for custom soldering or terminal block insertion.
-
Product
Additional Products: High Voltage 37 Pin D-Type Cables - Connector to Unterminated
-
The connector to unterminated cable assemblies below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
Product
Cable Assembly, Receiver, 20", Mini Power/TriPaddle, 9 Pin DIN, 4 Banana Plugs
540039030111
-
Cable Assembly, Receiver, 20", Mini Power/TriPaddle, 9 Pin DIN, 4 Banana Plugs.
-
Product
Pin Moisture Meter
-
Pin meters can measure all thicknesses from veneer to logs, flat boards or round and oddly shaped pieces, obtain surface and core measurements. Adding electrodes, pins (up to 7″) optimizes usage. For green, air-dried and kiln-dried lumber.
-
Product
Pull-Thru Adapter, Wired, QuadraPaddle, to 100 Pin ML SCSI, f/ NI PXI-6514/15, 6509
510140113
-
Pull-Thru Adapter, Wired, QuadraPaddle, to 100 Pin ML SCSI, f/ NI PXI-6514/15, 6509.
-
Product
200 Pin D Cables - 200 Pin to 200 Pin for Pickering Products
-
The connector to connector cable assemblies below are suitable to use with Pickering cards and modules that utilize a 200-pin D connector.
-
Product
Cable Assembly, 50-Pin D-Type, Male to Unterminated With Tinned Ends, 2m HV, Exit Away From Pin 1
A050DM4-T-HA200
-
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
