-
Product
04 With Pins For PCB | 2 Wafers | 24 Positions
04-2xx3-20/70-xx
-
Very robust, multi wafer selector with 15° detent angle, switching torque up to 20 Ncm and a rotational life up to 25'000 cycles
-
Product
37-Pin D-Type Male Solder Pin HV
40-960-037-MHV
D-Sub Male Connector
This connector is designed to allow users to directly terminate cables with soldered connections.
-
Product
Mating Coax Connector And 20 Coax Pins Crimped (One End) To 3 Foot Wires
GX96404
-
Mating Coax Connector and 20 Coax Pins Crimped (One End) to 3 Foot Wires
-
Product
68 Pin 1.27mm Pitch Micro-D Connector & Cable Accessories
-
The 68 Pin 1.27mm Pitch Micro-D Connector is used on high-density PXI modules that require 1A current rating and voltage handling up to 150Vdc.
-
Product
Cable Assembly, 50-Pin D-Type, Male to Unterminated With Ferrules, 2m HV, Exit Away From Pin 1
40-972-050-2m-MU-HV
Cable Assembly
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
-
Product
26 Pin D-Type Connectors for Pickering Products
-
The connectors below are suitable to use with Pickering cards and modules that utilize a 26-pin D-type connector.
-
Product
Cable Assembly, 50-Pin D-Type, Female to Female, 1m, Exit Away From Pin 1
40-970-050-1m-FF
Cable Assembly
The 50-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products and is constructed from PFA insulated wire. The connector assembly can be secured to the product by screwlocks.
-
Product
50 Pin IDC Cables - 50 Pin Connector To Unterminated
-
50-pin IDC cables (2x25 matrix, 2.54mm pitch) connect to SCSI, I/O racks, or PCB boards, with one end featuring a female/male IDC connector and the other being unterminated (bare wire or tinned) for custom soldering or terminal block insertion.
-
Product
Terminal Block and SCSI-II 68 Pin Connector with 2 Meter Cable
U2902A
Terminal Block
The Keysight U2902A is an accessory compatible and recommended to be used with the U2300A Series USB Modular Multifunction Data Acquisition and U2500A Series USB Modular Simultaneous Sampling Multifunction Data Acquisition. The pin-outs of the U2902A is dependent on the USB Data acquisition unit that it is working with. For more information, please refer to the data sheet or the user guide of the USB Data Acquisition unit that U2902A is to be used with.
-
Product
Cable Assembly, 50-Pin D-Type, Male to Unterminated With Ferrules, 0.5m HV, Exit Away From Pin 1
40-972-050-0.5m-MU-HV
Cable Assembly
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
Additional Products: 26 Pin D-Type Cables - Connector to Connector
-
The connector to connector cable assemblies below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
Product
44 Pin D-Type Cables - Connector To Connector For Pickering Products
-
The connector to connector cable assemblies below are suitable to use with Pickering cards and modules that utilize a 44-pin D-type connector.
-
Product
96 Pin 1.27mm Pitch Micro-D Connector & Cable Accessories
-
The 96 Pin 1.27mm Pitch Micro-D Connector is used on high-density PXI modules that require 1A current rating andvoltage handling up to 150Vdc.
-
Product
Cable Assembly, 50-Pin D-Type, Male To Unterminated With Ferrules, 0.5m HV, 45º Exit Away From Pin 1
40-972-050-0.5m-MUHV
Cable Assembly
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock.
-
Product
Standard Voltage 50 Pin D-Type Connector Blocks and Breakouts for Pickering
-
The connector blocks and breakouts below are suitable to use with Pickering cards and modules that utilize a standard voltage 50-pin D-type connector.
-
Product
50 Pin IDC Connectors
-
The connector below are suitable to use with Pickering cabling products that utilize a 50-pin IDC connector.
-
Product
DL-ISO 2500 Vpp Square Pin Tip
DL-ISO-2500V-TIP
-
- Ideal for GaN and SiC devices- Highest system accuracy- Fastest rise time- High CMRR - 160 dB
-
Product
Pin Grips For Flat Specimens
-
Pin grips are very user friendly and are designed for conducting tensile tests of hard metal plate specimens that are difficult to grip. Specimens are held within the grips by passing pins through holes in the specimens.
-
Product
Cable Assembly, 50-Pin D-Type, Female to Unterminated With Cut Ends, 2m HV, Exit Towards Pin 1
A050DF5-C-HA200
Cable Assembly
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
Additional Products: High Voltage 50 Pin D-Type Connectors
-
The connectors below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
Product
50 Pin IDC Cables - 50 Pin Connector To 50-Pin Connector
-
A ribbon cable, often with a 2.54mm (0.1") or 1.27mm pitch, designed for connecting internal computer components, such as SCSI-1 drives or, more commonly, I/O boards, sensors, and industrial equipment
-
Product
Cable Assembly, 50-Pin D-Type, Female to Unterminated With Cut Ends, 1m HV, Exit Away From Pin 1
A050DF4-C-HA100
Cable Assembly
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
Cable Assembly, Receiver, TriPaddle, 36", RS-422 68 Pin ML VHDCI
540120110203
Cable Assembly
RS-485 cable 36 inch to 96 Pin TriPaddle Module
-
Product
96 Pin 1.27mm Pitch Micro-D Connectors for Pickering Products
-
The connectors below are suitable to use with Pickering cards and modules that utilize a 96-pin micro-D connector.
-
Product
Cable Assembly, 50-Pin D-Type, Male to Female, 2m HV, Exit Away From Pin 1
40-970-050-2m-MF-HV
Cable Assembly
50-Pin D-Type HV Cable assemblies are constructed from 24 AWG Tinned Copper Wire with PTFE Type C insulation. The connector assemblies can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
78 Pin D-type Connector & Cable Accessories
-
The Standard Voltage 78 Pin D-Type connector is used on PXI and LXI switching products to provide a medium density user connector solution.
-
Product
160 Pin Female DIN to QuadraPaddle Flying Lead Cable, 60", 024070
VFL103124-060
Flying Lead Cable
Vendor Flying Lead (VFL) Cable, 160 Pin Female DIN to QuadraPaddle Leads, 24AWG Twisted Pair, 80 T/P's(1:2) 160 connection points, M2.5 x .45 fastener, CONN: 024070 WIRE: VPC, for PXI-2737, PXIe-2738 families, VPC Contact 610138216 - QP RCV (22AWG-28AWG) (5 AMP/25 mΩ MAX), 20" length.
-
Product
Pin Converters
-
Blackhawk provides several different emulation pin converters to fit Texas Instruments standard JTAG target headers. This includes 14-pin TI, 20-pin cTi & ARM, 10-pin ARM, 60-pin XDS560 Trace and System Trace. All pin converters are available from the our Online Store or an authorized Blackhawk reseller.
-
Product
SP4T RF Pin Diode Switches To 16 GHz
-
The 4-way series of absorptive and reflective switches operate from 100 MHz to 16 GHz. They are rated at 200 mW maximum input power and have a switching time of 100 ns. SP4T switches that operate up to 8 GHz have a maximum VSWR of 1.6:1 and minimum isolation of 60 dB. All absorptive and reflective switches manufactured by Pulsar Microwave require both positive and negative 5-volt supplies. Additionally, the TTL control logic operates from 0 to +5 VDC. Voltage connection is made with feed thru terminals. Ground connection is made through the chassis and turret terminals.
