PMC Adapters
Computer boards that translate the data from the PMC bus to another bus and vice versa. They are used to connect two incompatible buses. (globalspec.com)
-
Product
Test Adapter
Ramcheck 72 Pro
-
Our latest addition to the RAMCHECK memory tester provides needed support for testing 72-pin SO DIMM modules used in older laptop computers. The RAMCHECK memory tester automatically detects the presence of the RC 72 Pro adapter
-
-
Product
Adapter
EXC-1553UNET/Px(S)
-
The EXC-1553UNET/Px is an intelligent, single - or - dual channel, MIL-STD-1553 adapter. Its small size and ability to interface through USB or Ethernet interfaces make it a complete solution for developing, testing and performing system simulation of the MIL-STD-1553 bus, both in the lab and in the field.The EXC-1553UNET/Px shares its API with the entire Px family so that applications currently running on PCI, PCIe, ExCARD or PCMCIA boards will run without change on this device.Multiple units can operate via USB ports on the same computer. In addition, multiple units can operate on the same network, by programming each one with a unique IP address, and can be accessed from any computer on the network.
-
Product
Tap Adapter
-
Techimp Voltage Tap Adapter is gender changer which allows the user to connect to the test tap (sometimes called power factor tap) of high voltage transformer bushings.While keeping the test tap well below the safety voltage level required by the manufacturer, the Tap Adapter lets the user to drain high frequency PD signals for diagnostic assessment of insulating materials.A synchronization signal can be derived as well.It is suitable for both single shot as well as continuous PD monitoring.Although it must be customized on the basis of the shape and dimension of the test tap (to be provided by the Customer), many models are readily available for the most established transformer bushings. A list of the presently available models is reported below.Several thousands of hours of operation are a guarantee of reliability and accurate design.
-
-
Product
Adapter for 980L-1A Tester
TA-331A
-
331A-9G HSI Adapter for use with the 980L-1A tester. Built to manufacturer's specs to allow by the book testing.
-
Product
Pull-Thru Adapter, Wired, QuadraPaddle, f/ Pickering 40-614A-002
510140253
Pull-Thru Adapter
Pull-Thru Adapter, Wired, QuadraPaddle, f/ Pickering 40-614A-002.
-
Product
Waveguide to Coaxial Adapter
D8-AWC650DNK-2298
-
Waveguide to Coaxial Adapter, Frequency 6.5~18GHz, 300W, Double Ridged Waveguide WRD650, N Type Female
-
Product
Coaxial Adapter, 3.5 mm (f) to 3.5 mm (f), DC to 26.5 GHz
83059B
Contact Adapter (Receiver)
The Keysight 83059B instrument-grade 3.5-mm female to 3.5 mm female coaxial adapter offers outstanding performance to 26.5 GHz. With SWR typically better than 1.05, this adapter is ideal for most connector saver and interconnect needs.
-
-
Product
USB to TTL Adapter
SKU-012-0X
-
The USB to TTL adapter connects the Serial UART to the standard USB port for testing and monitoring functionality. The Adapter facilitates ease of use and helps to reduce board space and cost.
-
Product
Run Down Adapters
Mini RDA
-
The mini RDA unit with fastener is designed for low torque sensors. Engineered to provide consistent and reliable torque readings for use with low torque power tools. The mini run down adapter is mounted in-line between the tool drive and torque sensor.
-
Product
PCIe Adapter for VPX
PCIe8LSwVPX3U
-
PCIe8LSwVPX3U is an 8 lane PCIe adapter with switch isolation for VPX development. The switch isolates the spread spectrum clocking found in most PC´s from the VPX port. PCIe 3.0 compliant, 1-8 lanes can be used by the installed VPX.
-
Product
RF Adapters
SMPM Adapters
-
a type of blind-mate, push-on connector that is similar to SMP connectors.
-
-
Product
Cables & Adapters
-
Are available in various lengths and are equipped with a variety of video, audio, and control connectors.
-
Product
Premium Microwave Cables And Adapters
-
Thorlabs' Microwave Cables and Adapter Cables are flexible, high-performance, coaxial cable assemblies designed for use out to 50 GHz, depending on connector type (see the image to the right). The design gives these cables flexibility while maintaining optimal performance. They exhibit low VSWRs (Voltage Standing Wave Ratios) over the usable frequency range, as well as low insertion losses (see the Specs tab). These cables are each tested to ensure performance.
-
Product
6U CompactPCI Dual 64-bit PMC Slots Carrier Board
cPCI-8602
Carrier Board
- Supports two single-size 32,64-bit/33,66 MHz PMC sites in 4HP width- PICMG® 2.0 32,64-bit/33,66 MHz cPCI bus- PICMG® 2.1 Hot Swap Specification Compliant- 3.3V or 5V V(I/O) for cPCI bus and PMC sites- PLX® PCI-to PCI bridge PCI6154 for PCI bus- Power and HotSwap LED incidators on front panel
-
Product
I2C Adapter
RS485
-
*RS485 address adjustable via DIP switch*I2C frequency adjustable up to 400kHz*I2C level shifter, I2C level from 2V to 15V*Interrupt input for external events*Simple software interface (ASCII commands)
-
Product
X.25 Adapters & XOT
FarSync X25 K2Ee
-
The FarSync X25 K2Ee PCIe card provides a very flexible 2 port PCI Express low profile X.25 communications platform for Linux and Windows systems.
-
Product
PCIe Adapter for PMC
PCIeBPMCX2
-
Embedded applications frequently require real time processing coupled with special purpose IO. With PCIeBPMCX2´s two positions a PrPMC can be matched with another PMC to make a high bandwidth processing node. The PrPMC can communicate with the host for set-up, and then use the local bus to control and transfer data with the special purpose IO card. For example the PMC-BiSerial-VI-HW1 provides 32 ports of manchester encoded data.
-
-
-
Product
USB Adapters
-
DekTec's classic and iconic portable adapters for USB bus are well known tools in the industry. Some of them can be considered essential tools for every DTV engineer! DekTec is proud that it has won prestigious awards at NAB and IBC for several of its USB adapters.
-
Product
PCI Adapter for cPCI
PCI2cPCI
-
PCI2cPCI is an adapter familiy used to mount a cPCI device into a PCI connector. PCI2cPCI-32, PCI2cPCI-32-IO, and PCI2cPCI-64 are passive devices with impedance controlled traces interconnecting the Gold Fingers of the PCI edge connector to the press fit cPCI connector. All PCI signals are routed through including power, ground, PCI bus, secondary control signals.
-
Product
Fiber Adapter
USB Serial Optical Converter
-
*Optical data transmission*Glass fiber or POF*Optimal galvanic isolation*USB bus-powered*Virtual serial interface*Baud rate up to 115kBit / s
-
-
Product
Digital I/O Adapter Module For FlexRIO
Digital I/O Adapter
Digital I/O Adapter Modules for FlexRIO offer up to 54 channels of configurable digital I/O that can interface with single‐ended, differential, and serial signals at a variety of voltage levels. When combined with a large, user‐programmable FPGA, you can use these modules to solve a variety of challenges, from high‐speed communication with a device under test to emulating custom protocols in real time.
-
Product
X.25 Adapters & XOT
FarSync X25 T4Ue
-
The FarSync X25 T4Ue PCIe card provides 4 high performance X.25 communications lines for Linux and Windows systems. A PCI bus version is also available.
-
Product
PMC-to-PCI Express Adapter
4749
-
Our PMC-to-PCI Express Adapter 1X (64-Bit) (4749) permits the use of a single-wide PMC module in a 1X PCIe slot. The product features a PEX8114 bridge running in transparent mode.
