PMC Adapters
Computer boards that translate the data from the PMC bus to another bus and vice versa. They are used to connect two incompatible buses. (globalspec.com)
-
Product
cPCI to PMC Compatible Adapter/Carrier
cPCIBPMC6UET
-
cPCIBPMC6UET ( cPCI to PMC ) adapter / carrier converter card provides the ability to install up to two PMC cards into a standard cPCI slot. cPCIBPMC6UET has two PMC card slots mounted to a universal voltage 6U 4HP cPCI card.
-
Product
PCB Adapter, Receiver, QuadraPaddle, 192 Position, to NI PXI-2532 with 36" Cables
510150143
PCB Adapter
PCB Adapter, Receiver, QuadraPaddle, 192 Position, to NI PXI-2532 with 36" Cables
-
-
Product
PMC Carrier PCIe x1
-
Looking for a way to plug your PMC mezzanine card into a computing platform with a 1-lane PCIe slot?Well, the CC_PCIeG1x1_to_PMC is your answer! It is effective, field tested and compliant with all applicable standards.
-
Product
MIL-STD-1553 Eight-Channel PMC Board
BRD1553PMC-STD-8
-
The PMC HyperBoard is a multi-standard PCI Mezzanine Card that contains eight channels of MIL-STD-1553 communication. The board is compatible with MIL-STD-1553B and MIL-STD-1760. Each channel can be configured independently to work with H009 and WB-194 in conjunction with MIL-STD-1553.
-
Product
PCIe Adapters
-
Teledyne LeCroy offers a broad spectrum of PCI Express protocol analyzer platforms (Summit T516, Summit T54, Summit M5x, Summit™ T416, Summit T48, Summit™ T3-16, Summit T3-8, Summit T34, Summit T28, and Summit T24). The Summit T516, T54 and M5x are Teledyne LeCroy’s leading edge products supporting PCIe 5.0 and CXL specifications. The Summit T416, T48, T34, T3-16 and T3-16 are Teledyne LeCroys midrange protocol analyzers. These protocol analyzers are at the forefront of SSD and computer storage analysis, test and compliance. The Summit T28 and T24 are entry level protocol analysis tools for development and test at PCIe 2.0.
-
Product
PMC Carrier with 4 positions
PMC-MC-X4
-
The PMC-MC-X4 adapter / carrier converter card provides the ability to install up to 4 (four) PMC cards into a small enclosure. The PMC-MC-X4 has two PMC card slots mounted front and rear to create a compact arrangement with 4 PMC slots. Suitable for 32/64 with 33/ 66 MHz bus operation.
-
Product
PMC Compatible Wizard Interface
PMC-Wizard
-
The PMC-Wizard is intended for use in ultra high-speed bidirectional point-to-point data transmission systems. The primary application is to provide very high-speed I/O data channels for point-to-point baseband data transmission over controlled impedance media of approximately 50 Ω. The maximum rate and distance of data transfer is dependent upon the attenuation characteristics of the media, and the noise coupling to the environment
-
Product
D.V.A. Adapter
640
-
*Read peak volts on CD ignition coils with your existing digital multimeter *New, completely redesigned unit is half the size of the previous adaptor *Adapts standard digital multimeter into peak reading voltmeter *High quality test leads with alligator clips are incorporated into the adaptor
-
-
Product
MTB Calibration Adapter
2450-CAL-30
-
The MTB Calibration Adapter (Catalog No. 2450-CAL-30)is a socket adapter that’s designed to bring phase A, B, and C current and potentials of a TESCO Multi-Position Test Board to an external RD-30 reference standard for calibration of the Test Board.
-
Product
2.4mm Adapters
-
Pasternack 2.4mm adapter category includes mostly RoHS and REACH compliant components. 2.4mm adapter series is part of a complete adapter product line from Pasternack.These 2.4mm adapters allow you to interface 2.4mm connectors with 1.85mm, 2.4mm, 2.92mm, 3.5mm, 7mm, N or SMA connectors. 2.4mm adapter series is manufactured in female to female, female to male, female to sexless, male to female, male to male or male to sexless gender varieties. The 2.4mm adapters category includes bulkhead or mountless configurations.Pasternack Enterprises' ISO 9001:2008 registered facility ships 2.4mm adapter parts the same day from the broadest and deepest in stock inventory of microwave and RF items. Excellent customer service and technical support are available to assist our customers.
-
Product
PCB Adapters - TriPaddle
-
TriPaddle signal technology adapted to a PCB with a variety of standard connector options. Allows for easy PCB integration with an interface while also offering wiring convenience. Offers "plug and play" functionality between module and instrumentation.
-
Product
DVB-T SFN Adapter
MIPDVB
-
MIPDVB for HDc is ENENSYS’ SFN adapter module for DVB-T that inserts synchronization data to enable Single Frequency Network broadcasting.Running at the head-end after DVB multiplexer, the MIPDVB runs in the HDc chassis to embed up to 6x MIPDVB modules in 1U so that the same chassis can output up to 6 TS with MIP packets over ASI or IP.
-
Product
Chip Test Adapter
SOJ EDO/FPM
-
Our new addition to the RAMCHECK line provides support for common 20 to 42-pin EDO/FPM DRAM SOJ chips of sizes 256Kx16/18, 1Mx16/18, 8Mx8, 16Mx4, 2Mx8, 4Mx4, 16Mx1, 1Mx4, and 4Mx1.
-
Product
RF Adapters
SMP Adapters
-
A subminiature interface in the same scale as MMCX connectors but offers a frequency range of DC to 40 GHz.
-
Product
Adapters
-
They allow a board with either tall components or heat sinks to be placed in a stack of boards in a location other than only at the top. The additional separation is 0.60 inches using standard PC/104-type spacers.
-
Product
Power Cord, AC, U.S., 120 VAC, 2.3 Meters
763000-01
Power Adapter
Power Cord, AC, U.S., 120 VAC, 2.3 meters
-
-
Product
Off-Card Adapter,
3910-FOFE
-
As the physical size of Fibre Optic Front End (FOFE) transceivers prohibits their use on PCI, CompactPCI, PMC and ISA (PC/AT) cards, Western Avionics provides an off-card Adapter, that contains all components to support the 3910 Optical implementation of STANAG 3910. The 3910-FOFE Adapter provides a complete dual redundant optical interface, together with dual redundant 3838 connections, and Trigger-in and Trigger-out in a minimal sized package, to allow convenient cabling connections to the 3910 / 3838 system or unit-under-test.
-
Product
PMC SpaceWire
-
PMC SpaceWire implements SpaceWire in a convenient PMC format. With PMC you can install the adapter into PCI [PCIBPMC], cPCI [cPCI2PMC], or processor board pmc slots. The SpaceWire specification calls for LVDS signaling and a specific 9 pin micro-D connector. You can connect the PMC-SpaceWire to other SpaceWire compliant devices without electrical interface issues
-
-
Product
Adapters
-
BroadWave designs and manufactures Coaxial Adapters and other coaxial RF components that are ideally suited for test, verification and system integration. Our products offer consistent performance at a low cost with an emphasis on performance and configuration flexibility.
-
Product
BGA SMT Adapters
Giga-snaP™
-
Giga-snaP™ 0.75, 0.8, 1.0, and 1.27mm pitch BGA Surface Mount Feet Adapter line of products provide an inexpensive and reliable method for attaching BGA chips to target board. The product line consists of patented female sockets with machined pins epoxy over-molded into an assembly that matches a particular BGA pattern. The epoxy over-molded female BGA socket is soldered to a PCB using standard soldering methods. A corresponding male pin BGA adapter, to which the user attaches their BGA chip, is plugged into the female socket on the board thus interconnecting the chip and the system is ready to go. The SMT adapters have the same solder ball types as the chips they are emulating. These adapters have less than half of the insertion force of competitive adapters, shorter electrical path for highest speed, and can be solder reflowed numerous times. A complete description and drawings of Giga-snaP™ 0.75, 0.8, 1.0, and 1.27mm pitch BGA Surface Mount Feet Adapters can be found at the tables shown below.
-
Product
FC Adapters
FY5
-
Best used in single mode applications and known for exceptionally accurate positioning, FC or Fixed Connection Connector is designed for use in unstable environments.
-
-
Product
Probe Adapters
-
Probe adapters provide simple and easy interface of third-party probes as well as change between the different Teledyne LeCroy Oscilloscope input and cable types (ProBus, ProLink, K/2.92 mm, BNC and SMA). Depending on the adapters, changing between the Teledyne LeCroy Oscilloscope's input type may have an effect on the overall performance of the channel.
-
Product
Adapter Plate, Receiver, f/ G20x or G40x
310113606
Adapter Plate
The G20x Adapter Plate allows the G20x or G40x Receiver to accept 2 modules (iCon) in the lower tier.
-
Product
Test Adapter
RAMCHECK® SIMM
-
The RAMCHECK SIMM Adapter is another addition to the RAMCHECK memory tester. It provides a needed solution for testing older 72-pin EDO/FPM DRAM SIMM modules. An optional adapter for 30 and 72-pin SIMMs is also available
-
Product
RF Adapters
BNC Adapters
-
Amphenol RF offers a wide array of both in-series and between-series BNC adapters in straight and right-angle configurations. 50-ohm and 75-ohm impedance BNC adapters are available with and without panel mounting features. Popular mounting features in bulkhead, both front and rear mount, and 4-hole flange designs. 50-ohm BNC connectors have a frequency range from DC to 4 GHz. 75-ohm BNC connectors optimized for 4K/UHD video applications can perform well to 12 GHz.
