Wiring
See Also: Wiring Analyzers, Trailer Harness Testers, Harness
-
Product
4 2/3 Digital Resistance Meter
CS2-RS
-
CS2-RS Resistance Indicator has been designed with high accuracy measurement, display and communication of Ohm (2 wire) as like as Coil of motor or transformer.The meter supports Field Calibration function. It can be calibrated with sensor (Resistance) to meet machinery structure.We build flexible function as like as 3 bank (for multi-range scaling and set point) and 3 external control inputs meet to various testing equipment inquiry.They are also building in 4 Relay outputs, 3 External Control Inputs, 1 Analogue output and 1 RS485(Modbus RTU Mode) interface with versatile functions such as control, alarm, re-transmission and communication for a wide range of machinery and testing equipments applications.
-
Product
Lan CAble Testers
-
TES Electrical Electronic Corp.
Tests a wide range of FTP & UTP cables. Tests for wiring faults such as open, shorted reversed.
-
Product
VVDI Programmer
-
MC9S08 series secured and unsecured , MC68 HC series (9) 12 secured and unsecured, MC9S12 series secured and unsecuredV850 series, H8X series, R8C series, R5F series, PCF79XX, EEPROM SPI, I2C, & mu WIRE, PIC 12F, 16F, 18F, Infineon TRICORE, Infineon XC2xxxx, Infineon XC164CS, ST10F series, ST7 series, STM8 series, ATMEL- Atmega 8, 48, 16, 32, 64, 128, 256, MPC560 series, SPC560 series, Fujitsu MB91F
-
Product
Super-Safeway Three Wire Circuit Tester
1301270009
-
Super-Safeway Three Wire Circuit Tester, 3 Indicating Lights & Receptacle Tension Tester in Carrying Case
-
Product
PreEqualization Analyzer
-
Quickly locate upstream impairments. See micro-reflections and group delay. Find issues like microfractures, reverse splitters, corroded connectors and bad wiring. Display modems being impacted by a common impairment. Save time and money. Reduce truck rolls. Lower maintenance costs. Increase operational efficiency.Improve customer satisfaction Benefit from pre-equalization without masking problems Find and fix problems before they impact customers
-
Product
Wireless
Beltpacks
-
Available as either single or dual channel units, the Trilogy 410 Series beltpacks are designed for 4 wire operation providing a convenient portable connection to any Trilogy intercom system. Each is fitted with a momentary ‘push to talk switch’ plus individual volume control(s) for the incoming audio level. These high performance beltpacks are suited for use with any quality low impedance headset equipped with dynamic microphone depending on the model.
-
Product
Cable Assy 68-Pin SCSI Micro-D M/M 2m
40-970A-068-2m-MM
Cable Assembly
The 68-Pin SCSI Style Micro-D Cable Assembly is constructed from 7/36 (28AWG) Copper Wire with Polypropylene insulation. Metal Spring Latches are provided to secure the connectors to their associated products.
-
Product
Four Wire Modem for SEL Mirrored-Bits
MBT 9600
-
Application specific features set the MBT9600 Four Modem apart from the conventional high speed modems. Its compact size and ease of installation make the MBT9600 an ideal, low cost alternative to conventional audio tone teleprotection systems.The circuitry is ideally suited for use over private networks such as conventional voice channels over analog microwave.
-
Product
Watchdog Timer and System Monitor Card
PCIe-WDG-CSMA
-
This multifunction Low Profile x1 PCI Express card contains a watchdog timer used to monitor the operation of your application program and operating system to initiate a system reset in case of a lockup. It can also monitor and control a variety of system hardware parameters. The card is 6.6 inches long and 2.535 inches seated height. I/O wiring connections are via a female DB25 connector on the card mounting bracket. Two models with increasing features are available.
-
Product
PXI Pull-Thru Adapter, Wired, QuadraPaddle, 68-Pin Male VHDCI
510140132-1
Pull-Thru Adapter
PXI Pull-Thru Adapter, Wired, QuadraPaddle, 68-Pin Male VHDCI
-
Product
6U VPX Single Board Computer
VPX6-195
-
Curtiss-Wright Defense Solutions
Our VPX6-195 6U OpenVPX T2080 Single Board Computer (SBC) combines performance with the advanced I/O capabilities of the NXP's quad-core AltiVec enabled T2080 processor. Designed for SWaP-constrained applications, the VPX6-195 provides two independent processor cores on a single printed wiring board (PWB) with a wide range of standard I/O and each with a XMC mezzanine site to provide twice the processing power.
-
Product
Cable Assembly, 78-Pin D-Type, Female to Unterminated With Ferrules
40-972-078-1m-FU
Cable Assembly
A 78-Pin D-Type to Unterminated cable assembly constructed from 7/0.15 (26AWG) Silver Plated Copper Wire. Screwlocks are provided to secure the cable connector to associated products. Has a 45 degree cable exit away from pin 1.
-
Product
Voltage Detector
-
Shenzhen Noyafa Electronic CO.,LTD
*Detect AC Power range : 50-1000V.*Test live wire and with flash indicate.*Locate wire break point easily.*LED assist using in dark place.*Certification. Passes RoHS, FCC, and CE compliance testing, and Noyafa is certified to the ISO 9001 standard.*100% Affordable. Manufactured in China and a lot cheaper than competitor products with similar quality.
-
Product
Digital Measuring Instrument
Earth Clamp
-
Digital measuring instrument for measurement on earthing and lightning protection systems. Specific earth resistance (soil resistance) measurement with a 4 wire method up to 30m deep.
-
Product
9050 VXI - 50 Module Solution for VXI cards
-
The 9050 VXI Solution is designed for use with VPC's pre-wired interconnect adapters on the top tier and discrete wiring modules on the bottom tier. The receiver opens downward via hinges to give the user access to the instruments in the rack. A microswitch, which comes standard, allows for shut off any power going through the system before removing the ITA. Using a plug and play plate or a flange kit allows for easy mounting of the receiver to any 19” rack system.
-
Product
uSD Logger Shield
IFB-11001
-
This micro SD logger shield enables time-stamped logging of any signals measured by your Arduino project! Whether sensor shields, breakout boards or datalink connections, this shield will get your logger project up and running quickly. We've included an MCP79410 Real-Time-Clock module for flexible supply voltage timekeeping, which includes an on-board battery holder for a CR1220 battery (included, and is installed). In addition, the micro SD card is interfaced through a high-speed translator IC and supplied with a high-current LDO to meet the demands of the SD standard. Each pin of the Arduino has an offset pin attached for easy wiring to the massive 13x9 pin prototyping area, including the pins connected to the ICSP header! Whether you're using a Mega, Due or Uno, this board has your interfacing needs covered! Finally, the micro SD holder is a push to lock, push to unlock type, which makes it really easy to both install and uninstall your card.
-
Product
Cable Assembly 68-Pin Micro-D Female to Unterminated, Tinned Ends
A068SFR-T-6A050
Cable Assembly
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by 2-56 UNC Screwlocks.
-
Product
Gauge Type T Thermocouple Wire
W-TW-36
-
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
Product
Earth Resistance Testers
-
Earth Resistance Tester is widely applied in ground resistance measurement, loop resistance measurement in fields such as electric power, telecommunications, meteorology, oil field, architecture and industrial electrical equipment, etc. When measuring ground system with loop, there is no need to disconnect the ground wire without auxiliary electrode, which means safer and faster.
-
Product
Power Quality Analyzer
PQM-703
-
Power quality analyzer PQM- 703 is a technically advanced product that allows for comprehensive measurements of the quality of electricity , analysis and recording of power network parameters, for frequencies 50/60 Hz in accordance with European standard EN 50160. PQM -703 is another representative of a well, known family of analyzers line PQM- 70x . In relation to the PQM -702 has new functions like recording of transients with max. sampling frequency 10 MHz (rapid changes in voltage) and control signals. Minimal transient capturing time is 650 ns. It is intended for a very wide range of users who need to control the quality of power with a mobile device , which fulfills the requirements of a multi-sheet standard IEC 61000 for class A analyzers. This applies to measurement accuracy, measurement methods, and synchronization of time with a standard signal. The last condition is met with a built-in GPS module with an internal antenna. If the analyzer is installed inside, it is possible to use an additional antenna with a 10m-long wire. If the antenna is situated outside, GPS signal will be attainable without any problems and used for the synchronization of an internal clock.
-
Product
Digitizers
2745 Family
-
The 2745 Digitizer is a 64-channel digital signal processor for radiation detectors available in VME64 (V2745), VME64X (VX2745), and Desktop (DT2745) form factor. It offers not only waveform digitization and recording but also Multi-Channel Analysis for nuclear spectroscopy using Silicon strip, segmented HPGe, Scintillation detector with PMTs, Wire Chambers, and others. The 2745 can perform pulse height measurements (PHA), constant fraction timing (CFD), charge integration (QDC) and pulse shape discrimination (PSD) independently for each of the 64 channels.
-
Product
Oscillatory / Wyzenbeek Abrasion Tester
TF212
-
TESTEX Testing Equipment Systems Ltd.
Wyzenbeek Abrasion Tester. Modern ergonomic design to determine the abrasion resistance of fabrics when rubbed against a standard abrasive or a wire mesh screen with a backward and forward motion over a curved surface. Wyzenbeek abrasion tester applies to automotive and furniture industry fabric manufacturers working to US Standards Motor driven with 4 abrasion heads and electronic digital counter to control the number of cycles.
-
Product
Electrical Circuit Tester with LCD Display
TE6-0717
-
Hangzhou Tonny Electric & Tools Co., Ltd.
*Used to detect voltage, power, ground and circuit integrity*LCD display provides a ‘no guess’ voltage value of the circuit*Backbit LED indicates Green for Ground or Red for Power*One hand free to jiggle wires, replace fuse or operate a switch*Surge protected circuitry displays 3 to 30V DC (± 0.3V accuracy)*Computer safe<10mA circuit draw for confident testing
-
Product
ITA, G10, 10 Module, Removable Backshell, Keying Feature, With Protective Cover
410104272
ITA
The G10 ITA is equipped with a removable EMI-shielded cover. The cover slides up to provide access to wires and connectors and is secured by two screws. The removable and adjustable U-shaped cable clamps are attached by screws to the ITA frame and allows ITA modules to be pre-wired before assembly. The clamps can hold cable bundles with an oblong bushing effective diameter of 1.55". ITA strain relief plates are not needed.
-
Product
4-Pin Power D-Type Cable, Male to Female, 0.5m
40-970-404-0.5m-MF
Cable Assembly
The 4-Pin Power D-Type cable assembly is constructed from 56/0.3 (12AWG) Copper Wire with PVC insulation. Screwlocks are provided to secure the connectors to their associated products.
-
Product
Cable Assembly. 9-Pin D-Type Male To Unterminated With Ferrules, 1m, HV
40-972-009-1m-MU-HV
Cable Assembly
A range of 9-Pin D-Type High Voltage cable assemblies with unterminated connections on one end, constructed from PTFE Type C insulated wire. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot breakwhen they are terminated.
-
Product
MS-M Style 26-Pin RF Cable, Female To SMB, 2m, RG316 Cable
40-979-526-3-2m-SMB
RF Cable Assembly
This 2m long MS-M style RF 26-Pin cable assembly is constructed from RG316 Silver Plated Copper Clad Steel Wire with PVC insulation and an attenuation of 68dB/100m at 500MHz . Screwlocks are provided to secure the MS-M style connector to the associated product.
-
Product
PXI/PXIe 1000Base-T1 Fault Insertion Switch, 6-Channel
40-203-002
Fault Insertion Unit
The 40-203-002 (PXI) and 42-203-002 (PXIe) are designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They support 6 channels of two wire serial interfaces. Each channel pair can simulate an open fault in either or both wires, and using the fault bus switches can simulate short between both wires or a short to one of two externally applied fault connections – such as battery supply or ground - via two fault buses.
-
Product
Industrial Clamp Meters
-
*Measures AC+DC current*AC and AC+DC voltage measurements with digital low pass filter for accurate readings on variable frequency drives*Also measures DC voltage, resistance, capacitance and frequency*Tests continuity and diodes*Flashlight inside clamp jaw for easier work in dark locations*Backlight & relative mode for added versatility*Peak-RMS measures motor inrush current*AmpTip™ increases accuracy on small wires and low current*Two voltage detection modes - non-contact or using a single test lead*Data hold*Recording of Maximum, Minimum, and Average readings*Crest (peak hold) feature captures current or voltage peaks as short as 5 milliseconds
-
Product
EPIC SBC With AMD G-Series APU, AMD A50M FCH, Dual DisplayPort/VGA/LVDS, Dual LANs And Audio
EP100
-
The EP100 EPIC board, supporting either the AMD G-Series APU dual core T56N with Radeon™ HD 6320 graphics or AMD G-Series APU single core T40R with Radeon™ HD 6250 graphics, combined with the AMD A50M FCH, is ideal for graphics-intensive applications such as high-end medical imaging, digital signage, kiosks/POI, thin clients, and gaming machines. The onboard SO-DIMM socket supports maximum up to 4 GB of DDR3 1333 memory. Integrated AMD HD graphics with DirectX 11 technology, the small foot print embedded board offers stunning 3D visual effects and dynamic interactivity. The EP100 comes with three display outputs with two combinations: two DisplayPort and one VGA or one DisplayPort plus a VGA and 18/24-bit single/dual channel LVDS. Additionally, it provides dual gigabit LAN ports for high-speed wired communication and two PCI Express Mini card expansion interfaces, one with SIM slot, for seamless wireless communication (WiFi + 3/4G).
