Conducted Immunity
EUT's resilience to an injected disturbance through associated cable.
See Also: Immunity Test, Coupling Decoupling Network
-
Product
Conducted Immunity Test Systems
-
Conducted Immunity System (CIS) to Test According to IEC 61000-4-6. The CIS series test systems are configured to perform conducted immunity testing according to IEC 61000-4-6. The system includes an ACS series power amplifier, coupling/decoupling Network (CDN), directional coupler, 150Ω to 50Ω adapters, power attenuators, cables and [optional] CSAT software. These systems, when properly configured, are capable of testing your products to all levels given in IEC 61000-4-6 up to 230 MHz. You can choose from three systems. Follow the links below for detailed information, including a comprehensive datasheet listing system specs.
-
Product
Conducted Immunity Test System
-
Conducted RF immunity tests acc. to IEC/EN61000-4-6 and BCI tests acc. to ISO 11452-4 and MIL-STD 461 CS 114 Signal generator,RF-power amplifier, RF-power meter and directional coupler (optional) in one 19”-caseStand-alone operation possible with optional available netbookControl-software includedMost important parameters are shown on an integrated displayAutomatic EUT-monitoringOperation via USB port of a PC or NotebookComplete range of CDNs available
-
Product
RF Conducted Immunity Test System
RFCI61000-4-6
-
RFCI61000-4-6 RF Conducted Immunity Test System is an automatic test system which is for the conduction sensitivity testing, it is fully meets IEC61000-4-6.2006, ISO11452-4, GB/T17626.6-2008 and GTB152B-CS114 etc standards. RFCI61000-4-6 internal source and broadband power amplifier can be generated 3 voltage test levels: 1v, 3v and 10v, and has the function of the real detect output level. It has two operation software which is calibration software and test software. When measuring, the signal is in 1 KHZ sine wave amplitude modulation system (80%) to simulate the actual harassment, and can through the coupling/decoupling network (CDN or electromagnetic clamp) to make the harassment signal coupled to the device.
-
Product
EMC Testing Knowledge & Equipment
-
Creating, delivering, installing, and training on EMC test systems; RF Immunity systems, RF Radiated and Conducted Emissions systems, Conducted Immunity and Pre-compliant EMC systems.
-
Product
Coupling Decoupling Network (CDNE)CDN
Emissions
-
CDNEs are based on the CDN as specified in IEC61000-4-6 (Conducted RF Immunity test). In this test, the CDN is used for the coupling of RF onto a cable. In principle, the CDN can be used in reverse, ie coupling any RF on the cable out to an analyser. In an earlier version of EN 55015, these CDNs were specified as suitable for measuring emissions. However, the current version of the standard specifies a CDNE which is essentially a CDN refined to deliver higher accuracy particularly at higher frequencies.
-
Product
EMC Testing Services
-
Our sophisticated technology can meet the diversified needs of customers. Component Tests: Immunity, Radiated Immunity, ALSE, TEM cell, Bulk Current Injection, Stripline, Conducted Immunity, Transient Immunity, Power Supply Variations, Electrostatic Discharge Emissions, Radiated Emissions, Conducted Emissions, Transient Emissions. Vehicle Tests - Radiated Immunity, Radiated Emissions.
-
Product
EFT Immunity Measurement
EFT61000-4
-
EFT immunity tester EFT61000-4 is specially designed according to the characteristics and requirements of EFT measurement and it is an ideal disturbance source of EMS measurement. They have fine performance, such as high stability, high reliability, easy to use etc. It meets the standard requirements of IEC 61000-4-4, EN 61000-4-4, GB/T17215.301, GB/T17215.322 and GB/T17626.4. EFT61000-4 has LCD display in both English and Chinese.
-
Product
Conductivity Sensor
ACF60-35
-
Knowing the conductivity of liquid samples is a key parameter to control product quality throughout the production process. The optek ACF60 conductivity sensor fulfils technical requirements of international regulations for reliable measurements ensuring quality and consistency.
-
-
Product
Conductivity Detector
CDD-10AVP
-
Low noise, low drift and wide dynamic range assure proven performance of the Shimadzu VP series HPLC. Data acquired by the CDD-10AVP is transferred to the SCL system controller via an optical fiber interface and are digitally processed by workstation. By adding the optional cell (dual kit NS), a low-cost and compact non-suppressor type dual ion chromatograph, which detects anions and cations simultaneously, can be made.
-
Product
Immunity DC
PGA 1240
-
The power generator PGA 1240 is suitable for EMC testing in accordance with standard IEC / EN 61000-4-16 in the frequency range from DC to 300 kHz.
-
Product
RF swept immunity package
EMiSweep
-
This is a flexible Windows immunity package which provides the utilmate flexible Graphical User interface. Other visual aids provides a swept as well as spot frequency assessment.
-
Product
EMI EMC test Solutions for Immunity
-
Scientific Mes-Technik Private Ltd
EMI EMC test Solutions for Immunity
-
Product
Conductivity Sensors
-
Conductivity sensors measure the specific conductance of liquid processes. The specific conductance is directly related to the presence of ionic species and their concentration. Barben Analytical offers a full range of two electrode and four electrode contacting conductivity sensors for a variety of industrial measurement applications.
-
Product
Immunity
RF coupling
-
is used for the conducted measurement of the immunity according to IEC 62132-4.
-
Product
Conductivity Switches
-
B/W Controls offers a simple conductivity holder and electrode that can be configured for multiple measurement points.
-
Product
Thermal Conductivity Analyzer
Model 2000B
-
Teledyne Analytical Instruments
The Series 2000 represents a complete line of Thermal Conductivity Detector (TCD) based analyzers which can be applied in a wide range of applications and industries. By using field proven filament-based and semiconductor based TC detectors, Teledyne is able to continuously monitor hydrogen and a variety of other gases of interest in either binary or multi-component sample gas streams.
-
Product
PRO Conductivity (EC) Controller
MC311
-
The Milwaukee MC311 PRO Conductivity (EC) controller lets you measure and adjust EC levels automatically.
-
Product
Battery Conductance Tester
FST-8000
-
Foresight Electronics Co., Ltd.
Profsional battery conductance tester for Lead-acid stationary (wet, flooded, gel, AGM, VRLA) battery cells/blocks, to measure actual capacity and aging for UPS, telecom, industrial, vehicle, solar or other applications' small and large battery banks.Battery Conductance Tester is a portable digital measurement device for testing lead acid stationary batteries health and aging condition precisely within seconds.
-
Product
Battery Conductance Tester
SAT-AC
-
Shaanxi Aitelong Technology Co., Ltd
SAT-AC Battery Conductance Tester is a multi-function and portable digital data storage measurement instrument to test battery running condition and parameters quickly and precisely. It can display and record many key parameters for multi-groups like battery string and each battery cell’s voltage, conductance, connecting strip resistance, battery’s internal resistance and so on; offer the ability to distinguish battery’s condition effectively and accurately; compose with intelligent PC measurement analyzing software, user can track battery’s decay trend, and alarm beforehand to help technician and administrators process according to status.
-
Product
Coupling Decoupling Network for Conducted Common Mode Immunity Testing According to IEC 61000-4-6
CDN
-
The CDN M5 is intended to inject common mode disturbance signals to power supply of mains lines (unscreened) in the frequency range from 150KHz to 230MHz. A variety of calibration adapters and other accessories are available as an option. RF Standard connector: BNC type, AC socket 4mm safety bananas.
-
Product
Immunity
ESD coupling
-
is used for conducted coupling of Langer ESD pulses (200ps rise time) into ICs.
-
Product
Conductivity Electrode
-
As current-carrying and potential difference measuring electrodes, platinum was deposited on a quartz glass substrate. Voltage terminal distance can be varied by changing the connection pin. In-situ measurement of the metal transition produced in a conductive polymer insulator doping, 4 terminal electrode is used, where for insulator layer with low doping side 2 terminal method and for metal layer with high doping side 4 terminal method is used for the measurement. With this electrode, become possible to have measurement in 15 distances by combining the connection terminal.
-
Product
Online Conductivity Controller
LD-LOCC-A10
-
Online Conductivity ControllerLD-LOCC-A10features 3 points conductivity calibration system, TDS measurement mode, and 4 to 20 mA output signal transmitter. The large and clear back light LCD displays Calibration and setup values, Temperature values, ATC (automatic temperature compensation) values, high and low limit of measurement. This controller measures Conductivity and TDS values in µS/ cm, and mS/ cm units.
-
Product
Electromagnetic Flowmeter for conductive liquids
Picomag
-
Reliable measurement and monitoring of industrial water, cooling water or warm water. Simultaneous measurement of flow and temperature. Flexible integration into all fieldbus systems via IO-Link. Commissioning and operation via Bluetooth® and SmartBlue App. Minimum conductivity ≥20 μS/cm. Fluid temperature –10 to +70 °C (+14 to +158 °F).
-
Product
5lb Conductive Rubber Electrode
PRS-801W
-
Probe to test resistance of floors, worksurfaces, floor mats, or other flat objects.
-
Product
Digital Conductivity Pen (EC)
CD611
-
The Milwaukee Conductivity Pen is designed for hydroponic and other growers to help you make sure that your plants are receiving the right amount of nutrient. Keep EC in your target range to help your achieve better results.
-
Product
Impulse Magnetic Field Immunity Tester
IMF61000-9
-
IMF61000-9 impulse magnetic field immunity tester is high performance test instrument which special designed for to do impulse magnetic field immunity test and fully meet IEC61000-4-9, EN61000-4-9 and GB/T17626.9 standards, also it come with high intelligent, high stable performance and easy operation characteristics.
-
Product
12/24/36V Conductance Battery Tester
MBT200
-
Tests 12V heavy-duty auto, truck, commercial, and marine batteries and 12/24/36V starter and charging systems including 42V mild hybrid systems. Eliminate tester input errors by choosing between automotive/truck battery or small automotive type batteries. LED bar graph immediately displays battery condition upon pressing TEST button. No conversion tables needed for CCA, SAE, IEC, EN or Ah. 390 to 650 CCA range (auto) and 650 to 1700 CCA range (truck).
-
Product
Electrical Conductivity Measuring Instrument
SIGMASCOPE® SMP350
-
Compact handheld device for measuring the electrical conductivity of non-ferrous metals.
