OBD 2
-
Product
PXI 2 Amp MUX, Quad 4-Channel 2-Pole
40-635-109
Multiplexer Module
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
PXI 2 Slot BRIC 184x4 1-Pole Matrix (2 sub-cards)
40-560A-221-184X4
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays.
-
Product
2 Channel Variable Optical Attenuator
S-105
-
VOA slot module of FOTS system is a module that installs a built-in dual channel MEMS type VOA inside and can do two separate attenuation functions with two each VOA channel being driven individually. This module controls the optical power precisely to maintain the desired output level set by the user by automatically correcting for power drift or fluctuation.This slot module provides high-performance power control features such as high attenuation range, accurate tolerance, stable spectral flatness and low insertion loss in the wavelength range of 1260 ~ 1600 nm. It also offers a particularity that the high-speed drive of attenuation is possible through the combination of high-speed FPGA processor and high speed response time (within 1 ms) VOA. With the provided driving program and GUI, users can set up various attenuation program of each VOA channel such as sequential attenuation step, periodic attenuation and operation time
-
Product
PXI 8 Slot BRIC 22x16 1-Pole (2 sub-cards)
40-562A-121-22X16
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
cRIO-9048, 1.30 GHz Dual-Core CPU, 2 GB DRAM, 8 GB Storage, -40 °C to 70 °C, Kintex-7 160T FPGA, 8-Slot CompactRIO Controller
785619-01
Embedded Controller
1.30 GHz Dual-Core CPU, 2 GB DRAM, 8 GB Storage, -40 °C to 70 °C, Kintex-7 160T FPGA, 8-Slot CompactRIO Controller - The cRIO-9048 is a rugged, high-performance, customizable embedded controller that offers Intel Atom dual-core processing, NI-DAQmx support, and an SD card slot for data-logging, embedded monitoring, and control. It includes a Kintex-7 160T FPGA with LabVIEW FPGA Module support for advanced control and coprocessing. The controller provides precise, synchronized timing and deterministic communications using Time Sensitive Networking (TSN), which is ideal for highly distributed measurements. This controller offers several connectivity ports, including Gigabit Ethernet, USB 3.1, USB 2.0, RS232, and RS485 ports. You can use the USB 3.1 ports to add a local human machine interface and program, deploy, and debug software, which simplifies application development.
-
Product
Fanless Embedded System With 7th Gen Intel® Core™ I7/i5/i3 & Celeron® Processors, Built-in Layer 2 Managed PoE Switch For Railway PC
tBOX400-510-FL
-
The tBOX400-510-FL is a two-in-one transportation-certified box PC with built-in layer 2 managed PoE switch for IP surveillance applications. The tBOX400-510-FL is certified with CE (Class A) and FCC and is in compliance with EN 50155 and EN 45545-2. This high-performance transportation box PC is powered by the 7th generation Intel® Core™ (Kaby Lake) or Intel® Celeron® 3965U processors, along with dual DDR4 SO-DIMM slots for up to 32GB of memory. The built-in 10-port managed switch is powered by Qualcomm's chip. The tBOX400-510-FL has a built-in 10-port managed switch with 8-port 10/100 Mbps PoE and 2-port Gigabit LANs, featuring VLAN, QoS and PoE scheduling for the more secure and smooth network. For reliable operation in severe environments, the rugged fanless transportation box computer is designed to withstand a wide temperature range from -40°C to +60°C and vibration of up to 3 Grms. It also supports a wide voltage input range: 9V to 36V DC for vehicle applications, 14V to 32V DC for marine applications, and 24V to 110V DC for railway applications. With its high performance, industrial-grade design and full-strict certifications, the tBOX400-510-FL is suited for transportation-related applications such as onboard video surveillance and video management.
-
Product
Oscilloscope, 350 MHz, 2 GS/s interleaved, 4 CH, 200 Mpts/Ch DSO, Fully Loaded with 10.1" Color Display
T3DSO2354HD
Oscilloscope
The T3DSO2000HD series of Bench Oscilloscopes feature 4-channel models with analog bandwidth options of 100 MHz, 200MHz and 350 MHz. The T3DSO2000HD Oscilloscopes use 12-bit high resolution ADCs and a low noise front end which provides an impressive noise performance to cover a wide range of measurement applications. Each model offers a maximum sample rate of 2 GSa/s (interleaved) and a maximum memory depth of 200 Mpts in interleave mode. The MS configured models also include a 16 channel logic probe as standard.
-
Product
PXIe-1090, Thunderbolt™, 2-Slot (1 Hybrid Slot), Up to 2 GB/s PXI Chassis
787040-01
Chassis
PXIe, Thunderbolt™, 2-Slot (1 Hybrid Slot), Up to 2 GB/s PXI Chassis - The PXIe‑1090 features a high-bandwidth backplane to meet high-performance test and measurement application needs. This PXI chassis features one hybrid connector, 58 W power and cooling, and an integrated. Thunderbolt 3 MXI-Express controller. Thunderbolt is a trademark of Intel Corporation or its subsidiaries in the US and/or other countries.
-
Product
Oscilloscope 59 GHz, 2 Channels
UXR0592B
Oscilloscope
The UXR0592B is the 59 GHz, 2 channel, Infiniium UXR-Series real-time oscilloscope.
-
Product
PXIe-6376, 8 AI (16-Bit, 3.5 MS/s/ch), 2 AO, 24 DIO, PXI Multifunction I/O Module
781475-01
Multifunction I/O
PXIe, 8 AI (16-Bit, 3.5 MS/s/ch), 2 AO, 24 DIO, PXI Multifunction I/O Module—The PXIe‑6376 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, four 32‑bit counters, and analog and digital triggering. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PXIe‑6376 is ideal for a variety of applications, such as IF digitization; transient recording; ISDN, ADSL, and POTS manufacturing test in the telecom industry; ultrasound and sonar testing; and high-energy physics. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
1U Rackmount Network Appliance With Intel® Xeon® Processor D Family For VE-CPE And Network Applications, 2 NMC Slots
FWA-3260
-
Intel® Xeon D-1500 Processors, up to 16 Cores with 2 x 10G MAC4 x DDR4 ECC RDIMM slots4 x 1GbE RJ-45, 2 x 10GbE SFP+ slots with 2 pairs of LAN bypass1 x PCIe x8 slot on rear, supports FH/HL add-on cardsIPMI v2.0 compliant BMC2 x Advantech network module expansions2 x internal 2.5" SATA HDDs/SSDs
-
Product
2 GHz Dual 1:4 RF Mux, 50 Ohm Module for DAQ970A and DAQ973A
DAQM905A
Multiplexer Module
2 GHz Dual 1:4 RF Mux, 50 Ohm Module. Direct connection to SMB inputs with 2 GHz usable bandwidth.
-
Product
1.5kV, 200 MHz, 2 pF, 10 M, Rise Time < 1.75 ns, High Voltage Differential Probe
T3HVD1500-200
Differential Probe
1.5kV, 200 MHz, 2 pF, 10 M, Rise Time < 1.75 ns, High Voltage Differential Probe.
-
Product
VME64x 1U/84HP 2 Slots
-
Hartmann Electronic’s slimmest 19” rack mountable VME solution – The VME64x 1U system. This thin VME chassis comes with a 250W cPCI hot-swap power supply and horizontally oriented card slots. This platform conforms to VITA 1.1-1997 while providing a low profile, practical packaging solution for high-performance processors.
-
Product
Programmable Linear DC Power Supply, 2 Output, 0-32V/0-3A
T3PS23203P
DC Power Supply
Programmable Linear DC Power Supply, 2 Output, 0-32V/0-3A.
-
Product
2 Channel 1GSPS 8 Bit ADC Card in FMC
FM582
-
Sundance Multiprocessor Technology Ltd.
The offset adjustment does not clip the signal at the highest range (+/- 5V). That is why the “max input signal amplitude” has been specified as 10V, even though the selection of signal ranges only goes up to 5V. This way, a +10V pulse with -5V offset could still be digitised without clipping.
-
Product
Combination Module: 2 Ch. MIL-STD-1553 & 12 Ch. Discrete I/O
CM8
-
The CM8 module is a combination of NAI's MIL-STD-1553B module, FTB, and Enhanced Discrete I/O module, DT4. The CM8 offers twelve channels of discrete I/O and two channels of MIL-STD-1553B communications. The twelve discrete I/O channels are programmable as either input (voltage or contact sensing with programmable, on-module pull-up/pull down current sources), or output (current source, sink, or push-pull) up to 500 mA per channel from an applied, external 3-60 VCC source. The discrete I/O channels also provide additional functionality modes such as Pulse Width Modulation (PWM) output mode and Pattern Generator output mode. The two MIL-STD-1553B communications channels feature a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
Product
PXI-6115, 4 AI (12-Bit, 10 MS/s/ch), Buffer Size 32MS, 2 AO, 8 DIO, PXI Multifunction I/O Module
778204-01
Multifunction I/O
4 AI (12-Bit, 10 MS/s/ch), 2 AO, 8 DIO, PXI Multifunction I/O Module - The PXI‑6115 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, two 24‑bit counters, and digital triggering. It is ideal for a variety of applications, such as stimulus/response applications where synchronization among analog input, analog output, and digital I/O is required, 42 V automotive applications, radar, sonar, and ultrasound. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
PXI Dual 2 Channel Fibre Optic LC
40-855-422
Fiber Optic Switch
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
Cable Assembly, Receiver, QuadraPaddle, 48", 2 50-Pin Female D-Subs
540111040640
Cable Assembly
Cable Assembly, Receiver, QuadraPaddle, 48", 2 50-Pin Female D-Subs.
-
Product
USB-6361, 16 AI (16-Bit, 2 MS/s), 2 AO (2.86 MS/s), 24 DIO USB Multifunction I/O Device
782256-01
Multifunction I/O
16 AI (16-Bit, 2 MS/s), 2 AO (2.86 MS/s), 24 DIO USB Multifunction I/O Device - The USB-6361 offers analog I/O, digital I/O, and four 32-bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI-STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB-6361 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
PXI 8 Slot BRIC Matrix, 2A 1-Pole 64x12, 2 Sub-cards
40-597A-102
Matrix Switch Module
The 40-597A-102 is a PXI 1-pole 64x12 matrix in BRIC8 format and is part of a range of high density matrix modules able to switch up to 2 A or 200 VDC/210 VAC. The 40-597A BRIC modules are available in 2, 4 or 8-slot sizes to suit most high performance PXI matrix requirements, constructed using high quality electro-mechanical relays for high switching confidence.
-
Product
PXI 4-Slot BRIC Matrix, 44x8 1-Pole (2 Sub-cards)
40-562B-021-44X8
Matrix Switch Module
The 40-562B-021-44X8 is a high density BRIC4 matrix module with a size of 44x8 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
Digital Roller Brake Tester for Cars and Vans up to 3.5 T Axle Load with 2 x 3 kW Drive Motors and Max. Track Width of 2,500mm
C_MBT C 3.5 W250 | VP 210153
-
Maschinenbau Haldenwang GmbH & Co. KG.
Digital roller brake tester for cars and vans up to 3.5 t axle load with 2 x 3 kW drive motors and a max. track width of 2,500 mm.Particularly suitable as stand-alone tester or as part of car reception and diagnostic test lanes for larger vehicles such as SUVs, off-roaders or vans.
-
Product
USB-6363, 32 AI (16-Bit, 2 MS/s), 4 AO (2.86 MS/s), 48 DIO USB Multifunction I/O Device
782258-01
Multifunction I/O
32 AI (16-Bit, 2 MS/s), 4 AO (2.86 MS/s), 48 DIO USB Multifunction I/O Device - The USB‑6363 offers analog I/O, digital I/O, and four 32‑bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB‑6363 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
PCIe-6351, PCI Express, 16 AI (16-Bit, 1.25 MS/s), 2 AO (2.86 MS/s), 24 DIO Multifunction I/O Device
781048-01
Multifunction I/O
PCI Express, 16 AI (16-Bit, 1.25 MS/s), 2 AO (2.86 MS/s), 24 DIO Multifunction I/O Device - The PCIe‑6351 offers analog I/O, digital I/O, and four 32‑bit counters/timers for PWM, encoder, frequency, event counting, and more. The device delivers high-performance functionality leveraging the high-throughput PCI Express bus and multicore-optimized driver and application software. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PCIe‑6351 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
PXI 2 Slot BRIC 138x8 1-Pole Matrix (3 sub-cards)
40-560A-221-138X8
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays.
-
Product
PCIe-6341, PCI Express, 16 AI (16-Bit, 500 kS/s), 2 AO (900 kS/s), 24 DIO Multifunction I/O Device
781046-01
Multifunction I/O
PCI Express, 16 AI (16-Bit, 500 kS/s), 2 AO (900 kS/s), 24 DIO Multifunction I/O Device - The PCIe‑6341 offers analog I/O, digital I/O, and four 32-bit counters/timers for PWM, encoder, frequency, event counting, and more. The device delivers high-performance functionality leveraging the high-throughput PCI Express bus and multicore-optimized driver and application software. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PCIe‑6341 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
USB2.0 Module With 2 CAN Bus Nodes ARINC825 Compliant For Testing & Simulation of Avionic ARINC825/CAN Bus Systems
APU825-2
System
USB2.0 module with 2 CAN bus nodes ARINC825 compliant for testing and simulation of Avionic ARINC825/CAN bus systems.
-
Product
USB-6363, 32 AI (16-Bit, 2 MS/s), 4 AO (2.86 MS/s), 48 DIO USB Multifunction I/O Device
782257-01
Multifunction I/O
32 AI (16-Bit, 2 MS/s), 4 AO (2.86 MS/s), 48 DIO USB Multifunction I/O Device - The USB‑6363 offers analog I/O, digital I/O, and four 32‑bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB‑6363 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
