-
Product
C-Band / L-Band MWDM
WD1615/C, WD1516/L
-
Hangzhou Huatai Optic Tech. Co., Ltd.
WD1615/C, WD1516/L WDM is based on mature thin film filtering tech, with wide bandwidth, flatness, low insertion loss and high isolation. It is mainly applied to EDFA and DWDM network to achieve the combination and separation of C-Band and L-Band.
-
Product
Airborne Receivers & Bit Synchronizers
-
The Lumistar LS-28-DRSM Series Multi-Mode Multi-Band Receiver/Combiner/TM Processing Unit is designed using ruggedized packaging to survive severe airborne conditions. The LS-28-DRSM is available in several configurations: 1) Airborne receiver only (RF to bits), 2) Airborne bit synchronizer only, 3) RF to TM Processing and Display (RF to bits to UDP decom to LAN Client Displays). Models with receivers are available in any band form 200 MHz to 7 GHz with S, lower L and C bands as standards. Other RF bands are available, please consult the factory for details. This unit can be mated with other Lumistar products to provide a complete air-to-ground re-transmission system.
-
Product
Rack Mounted Spectrum Analyzer
-
Designed for the measurement and analysis of communications and broadcast carriers, making uplink, down- link, L-Band carriers, IF, and 10MHz reference signals easy to measure, monitor, and store.
-
Product
3-Port ROADM / TOADM
-
Optoplex's Reconfigurable Optical Add/Drop Multiplexer (ROADM) module, also known as Tunable Optical Add/Drop Multiplexer (TOADM), is based on a proprietary micro-optics and micro-actuator design, athermal packaging technology, and state-of-the-art thin-film coating. When receiving a stream of optical signals of a plurality of wavelengths from the Input-Port (IN), this 3-port ROADM device directs a selected channel to the Drop-Port (ADD/DROP) and the remaining channels to the Express-Port (EXP), as depicted in the figure below. This tunable feature can also be used for adding a channel, when the device is used in reverse. Cascading two ROADM modules, simultaneous add and drop functions can be achieved. Each single ROADM device is optimized to cover either C- or L-band wavelengths. The standard 100- or 200-GHz channel spacing ROADM products allow for single-channel drop. Customized banded-channel drop ROADMs are available upon request.
-
Product
GPS/GNSS Anti-Jam Antenna
8230 AJ
-
The 8230AJ anti-jam antenna is a high gain (40 dB) GNSS outdoor antenna with a unique conical antenna pattern that rejects interference from the horizon. The antenna rejects signals at lower elevation angles – where most of the interference comes from – and only receives signals from higher elevation angles where the true satellites are. This way, you get all the performance and timing accuracy you would with a standard antenna plus 20 dB or more of interference rejection.It uses a three-stage low noise amplifier, a mid- section SAW, and a tight pre-filter to protect against saturation by high level sub-harmonics and L-band signals. The antenna covers GPS L1, GLONASS L1, BeiDou B1, Galileo E1, and QZSS L1.
-
Product
RF over Fiber Link TX/RX
L-Band
-
QuestTel's Satellite L-Band optical fiber Transmitter/Receiver set offers high pefromance and cost effective alternative to conventional coaxial systems. The L-Band Transmitter and Receiver pair is used for transporting L-Band RF over fiber from the antenna to the satellite receiver. Additionally transmitter provides optional 13/18V LNB power as well as Automatic Gain Control (AGC) to manage RF input level. By transporting the L-Band RF over fiber this range can be extended from several hundred feet to over 80 miles. Since optical signal is not affected by electromagnetic field, the quality of your signal will always stay at the high level. Also this fiber solution is more cost effective than coaxial system, as well as more reliable and flexible.
-
Product
RF Amplifiers up to 2500 MHz
-
L and S Band 1,2,4, and 8 Kilowatt rack mount solid state microwave amplifiers ideal for CW and pulse TWT amplifier replacement utilizing GaN technology and rivals the TWT amplifier in size and weight. Also available is our broad line of high power modules including 25, 50, and 100 watt pallets for integrating into your own power amplifier design.
-
Product
Modulators
ZMOD-X1
-
Antenna Technology Communications, Inc.
The ZMOD-X1 modulator series is an all inclusive unit that is loaded with features most needed by broadcasters. In it's most basic form, the unit comes with DVBS, DVBS2 and 8PSK modulation schemes, IF output, L band output and ASI input all as standard features. 16 APSK modulation and IP input are provided as options. Taking mobile and portable systems in mind, the unit comes with clear and user friendly front panel control. Size and weight are significantly less than any unit on the market. The unit can also be monitored and controlled using any web browser.
-
Product
Compact Tunable Laser Source with Continuous Sweep Mode, 1520nm to 1630nm
81940A
Laser Source
Keysight's 81940A high power compact tunable lasers enables optical device characterization at high power levels and measurement of nonlinear effects. It's improves the testing of all types of optical amplifiers and other active components as well as broadband passive optical components. As single slot plug-in modules for Keysight's 8163A/B, 8164A/B and 8166A/B mainframes, they are a flexible and cost effective stimulus for single channel and DWDM test applications. Each module covers a total wavelength range of 110 nm in the C+L-band.
-
Product
Channelized Down-Converter
DCV Series 5” x 2.5” x 0.6”
-
*Connectorized Package *Wide Choice of Frequency Ranges *Integrated Filters *Gain Control *L-Band to 70 MHz IF Range Available *L-Band to 140 MHz IF Range Available *CAN, RS-232, I2C, or SPI Control *Internal / External References *Custom Designs Available *Low Power Consumption *Low Phase Noise *Low Spurs
-
Product
RF Management
-
ATX offers several high performance, modular and integrated, RF and L-Band signal management platforms. Operators can easily split/combine RF services in a cost-effective and space-efficient manner. The MAXNET II and SignalOn platforms are CCAP™ compliant and support DOCSIS® 3.1 services up to 1.2 GHz, and also deliver up to 4K QAM signals without impairment due to RF management. ATX also offers the most comprehensive line of RF amplifiers and related products on the market.
-
Product
Laser Sources and Amplifiers
Amplifier
We design and manufacture a range of tunable C-band and L-band telecom laser sources, customizable fixed-wavelength laser sources, broadband super luminescent (SLED) sources, swept laser sources, and Erbium-Doped Fiber Amplifiers (EDFA).
-
Product
Unified Satellite Phone Monitoring System
-
Unified Satellite Phone Monitoring System is designed to intercept Voice, SMS and Text traffic from Satellite Phones operating on Thuraya, Iridium and IsatPhone Pro Satellite networks. The system is pre-integrated & pre-configured in a compact ruggedized transportable casing for plug and play operations. It intercepts the signals from L-band uplink (from Satellite Phones to Satellites) and downlink (from Satellite to Satellite Phones) to provide the duplex calls up to 15 Kms with LOS and beyond that simplex calls. System is equipped state-of-the-art high performance Thuraya and IsatPhone Pro decryption module , Iridium proprietary protocol module to provide processed intelligible output in the form of Voice, SMS and Text along with session related information such as Called Phone Number (for session initiated by Satellite Phone),Caller ID, TMSI/IMSI/IMEI and geo-location
-
Product
L Band Splitter, DC Block All Ports
PD5142
-
INSTOCK Wireless Components, Inc
Wideband Frequency (698 - 2700 MHz)Low Insertion Loss (0.4 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)50 VDC maximum on DC block portsTri Alloy SMA Female (Jack) Low PIM
-
Product
Attenuators
-
OZ Optics offers a broad range of both variable and fixed attenuators having key competitive advantages. All of our attenuators operate over the two standard wavelength bands, the C-Band and the L-Band. This wide wavelength range makes these components ideal for DWDM applications. Our attenuators are wavelength insensitive, which means they operate with minimal changes in attenuation when used in either the C-Band or the L-Band and exhibit low return loss. In addition, all of our attenuators have a wide attenuation range, which means they operate at a wide range of power levels. This is important as increased power levels are being used in newer optical systems.
-
Product
Wavelength Meter
S-107
-
Wavelength meter slot module of FOTS system offers two main functions of an accurate wavelength meter and a precise tunable band-pass filter. This accurate instrument, which is based on an internal tunable filter, acts as an optical spectrum analyzer or a wavelength meter as well as a low insertion loss tunable filter. The built-in tunable filter of the module is precisely tuned in C-band and L-band optical communication window by using both electronic and optical controlling methods. User can choose the function of this module depending on his or her applications.
-
Product
Lasers
-
Alnair Laboratories Corporation
A narrow-linewidth wavelength tunable laser source for applications such as coherent communication and long-range optical sensing. The laser can be locked to ITU grid wavelengths and fine-tunable with 1 MHz resolution. The laser can be controlled on the front panel or remotely via USB/GPIB. Benchtop version can host up to 4 separate lasers, with a combination of C- or L- band tunable laser.
-
Product
L-Band Separate Raman Fiber Amplifier
RFA6000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
1. Erbium-doped Fiber Amplifier, due to the multiple cascades and the accumulation of noise caused by spontaneous emission, will reduce the system CNR greatly and thus it will limit the transmission capacity and distance of the system. Raman Fiber Amplifier (RFA) is a newly designed fiber amplifier based on Stimulated Raman Scattering (SRS) effect. It is considered as the core technology of new generation DWDM fiber over-long communication. Compared with Erbium-Doped Fiber Amplifier, Raman amplifier has the advantage of low Noise Figure (NF), wider gain bandwidth, flexible gain spectral region and stable temperature. It is the only device that can operate in 1300~1600 nm.
-
Product
Amplified Spontaneous Emissions (ASE) Sources
-
The AP505xA series, high power ASE sources provide stable output power up to + 23dBm and broad flat spectrum over C+L band or T band. They enable effective and efficient measurements for component characterization or optical sensing. Finally, these products are proposed in friendly-user stand alone benchtop instrument with touch sensitive screen, GPIB, ethernet, RS-232 or USB controls.
-
Product
L-Band RF Tuner and 2-Channel 500 MHz A/D with Virtex-7 FPGA - XMC
Model 71791
-
- Accepts RF Signals from 925 MHz to 2175 MHz- Programmable LNA handles L-Band input signal levels from -50 dBm to +10 dBm- Programmable analog downconverter provides IF or I+Q baseband signals at frequencies up to 123 MHz- Two 500 MHz 12-bit A/Ds digitize IF or I+Q signals synchronously; optional: 400 MHz 14-bit A/Ds- Two FPGA-based multiband digital downconverters- Xilinx Virtex-7 VX330T or VX690T FPGAs- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 & 3) interface, up to x8- Clock/sync bus for multimodule synchronization- VITA 42.0 XMC compatible with switched fabric interfaces- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O
-
Product
2.5G DPSK Demodulator
-
Optoplex’s Optical DPSK Demodulator, also known as Delay Line Interferometer (DLI), converts phase modulation to amplitude modulation over the entire C+L band in support of data transmission rates of 2.5, 10 or 40 Gb/s. The DPSK demodulator is designed for phase modulated optical communication systems utilized in commercial, defense and space exploration markets. The device plays a key role in improving signal quality and performance to meet the expanding demand for higher data rates and more complex transmission formats within current and next generation systems without major capital expenditure. Optoplex’s DPSK Demodulator is based on a patented free-space optical design, which is compact, athermal and polarization-independent. Themeasured frequency drift over temperature is only ~0.02 GHz/°C for our standard passive device. Further, this DPSK Demodulator exhibits a total polarizationdependent phase shift of less than 2 degrees over the entire operating temperature range with a high extinction ratio. Optoplex’s DPSK Demodulators can be configured to be fully tunable, colorless tunable or purely passive. Dual-Rate DPSK Demodulator is also available.
-
Product
L Band Splitter, DC Block All Ports
PD5062
-
INSTOCK Wireless Components, Inc
Wideband Frequency (698 - 2700 MHz)Low Insertion Loss (0.5 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.15 : 1 avg)50 VDC maximum on DC block portsTri Alloy Type N Female (Jack) Low PIM
-
Product
With SAT-IF input EDFA
HA4600/IF
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HA4600/IF series, is narrow-band multiplexing EDFA suitable for L-Band fiber link application. With build-in 1550nm Internal Modulation SAT-IF optical transmitter, used for inter-cutting DBS. The WDM inside will multiply the signal from TX and main line signal that is inputted from outside, then the combined signal will enter EDFA to be amplified to serve the local subscribers. To avoid the interferes caused by mismatching of the optical output power between TX and main line signal from outside, output power of the TX can go through a VOA, thus, it can be adjusted or set from the front panel. This unit is simple and clear, easy to be installed and tested. It offers a high quality and cost-effective solution for inter-cutting DBS into full optic relay 1550nm fiber CATV system and second-stage service area.
-
Product
Thuraya Interception System
-
The Strategic Thuraya Monitoring System is designed to monitor Thuraya Satellite Phones operating on Thuraya-2 or Thuraya-3 Satellites network. The System is capable of providing both sides of the communication (full duplex call), call related information (CRI) along with the location of the Thuraya Phone by monitoring of both L & C-band. The Monitoring of L-band (between Thuraya satellite and Thuraya mobile) and C-band (between Thuraya Satellite and Thuraya Gateway), provides total traffic monitoring of the targeted spot beams each of which are nearly 350 - 400 Km. Normally 7 spot beams are available at any location under the Thuraya footprint.
-
Product
L-Band RF Tuner, 2-Channel 200 MHz A/D, Virtex-6 FPGA - x8 PCIe
Model 78690
-
Model 78690 is a member of the Cobalt® family of high performance PCIe boards based on the Xilinx Virtex-6 FPGA. A 2-Channel high-speed data converter, it is suitablefor connection directly to the RF port of a communications or radar system. Its built-in data capture features offer an ideal turnkey solution
-
Product
L-Band RF Tuner and 2-Channel 400 MHz A/D with Kintex UltraScale FPGA - 6U VPX
Model 57891
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Accepts RF signals from 925 MHz to 2175 MHz- Programmable LNA handles L-Band input signal levels from -50 dBm to + 10 dBm- Programmable analog downconverter provides IF or I+Q baseband signals at frequencies up to 123 MHz- Two 400 MHz 12-bit A/Ds digitize IF or I+Q signals synchronously- Two FPGA-based multiband DDCs (digital downconverters)- Xilinx® Kintex® UltraScale™ FPGA- Five GB of DDR4 SDRAM- Sample clock synchronization to an external system reference- PCI Express interface (Gen. 1, 2 & 3) up to x8- Clock/sync bus for multimodule synchronization- Optional LVDS and gigabit serial connections for FPGA for custom I/O- Navigator BSP® for software development- Navigator FDK® for custom IP development- Spark® fully-integrated development system- Free lifetime applications support- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
L-Band RF Tuner and 2-Channel 400 MHz A/D with Kintex UltraScale FPGA - 3U VPX
Model 54891
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Accepts RF signals from 925 MHz to 2175 MHz- Programmable LNA handles L-Band input signal levels from -50 dBm to + 10 dBm- Programmable analog downconverter provides IF or I+Q baseband signals at frequencies up to 123 MHz- Two 400 MHz 12-bit A/Ds digitize IF or I+Q signals synchronously- Two FPGA-based multiband DDCs (digital downconverters)- Xilinx® Kintex® UltraScale™ FPGA- Five GB of DDR4 SDRAM- Sample clock synchronization to an external system reference- PCI Express interface (Gen. 1, 2 & 3) up to x8- Clock/sync bus for multimodule synchronization- Optional LVDS and gigabit serial connections for FPGA for custom I/O- Optional optical interface for data streaming- Navigator BSP® for software development- Navigator FDK® for custom IP development- Spark® fully-integrated development system- Free lifetime applications support- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Fiber Optic Test System
OPTOWERE-S100 (Fiber Optic Test System)
-
The frame of FOTS system consists of the Main control part and the Slot mounting part. The Main control part is in charge of control and interface of the system and the Slot mounting part can hold up to maximum 8 slots, which are modularized according to each function and come out in five kinds. This integrated test system is designed to help manage the test and measurement related to optical communication and component. And the modular architecture of FOTS allows for customized configuration so that the slot of LD Driver, 2 channel VOA, 1 X 4 switch, WDM EDFA and C + L – Band ASE Source can be chosen according to user’s necessities. Main control part and each function module are run by effective and multi-functioned system control program in the base of high speed remote interface, GUI display and the discriminative high speed driving of module and system. This system can provide variety manufacturing and laboratory applications such as general quality test and reliability test of optical component and optical signal transmission test through efficient linkage with other system.
-
Product
1231a Very High Frequency Distribution
-
Precise Time and Frequency, Inc.
The ptf 1230A(1U)/1231A(2U) GPS L-Band RF Distribution amplifiers provide high performance GPS signal references for laboratory or systems use. In most applications the low noise and signal gain capability of the units will provide userswith a robust GPS signal source for lab or system requirements.The ptf 1230A/1231A uses individually buffered output stages and insures maximum isolation between the individual outputs. The ptf 1231A offers 12 outputs. Options are available for a 2U/3.5” version (ptf 1230A) with 24 outputs.Isolation from output to output is >-40 dB. The input also offers DCV for biasing an active antenna.
-
Product
L Band Splitter, DC Block All Ports
PD5182
-
INSTOCK Wireless Components, Inc
Wideband Frequency (698 - 2700 MHz)Low Insertion Loss (0.6 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.15 : 1 avg)50 VDC maximum on DC block portsTri Alloy SMA Female (Jack) Low PIM
