-
Product
Universal Band Decoder
Bandmaster III
-
The Bandmaster III universal band decoder is a highly integrated unit that not only decodes band information using YAESU “band data” (note 1), but can sense band information for all bands from160M through 6M, including 160M, separate 80M and 75M, 60M, WARC bands and 6M by monitoring CAT (note 2) data going to and from the radio. The Bandmaster III also contains all circuitry for level conversion thus eliminating the need for a separate CAT radio interface (note 3).
-
Product
Band Pass Filters
-
High-Pass (HPF series), Low Pass (LPF series) and Band Pass (BPF series) Filters are available, providing desired skirt selectivity and rejection levels with minimum insertion loss in the pass band. The filters are offered in all standard waveguide bands covering 18 to 400 GHz depending on our possibility to fulfil the customers' requirements. Dimensions of filters depends on required specifications. .
-
Product
Ku Band Gain Control Amplifier
-
Expanding Teledyne RF & Microwave's existing line of high frequency amplifiers, microwave gain controllable amplifiers are designed and biased for critical performance applications. One example covers 10-13 GHz, offers 45 dB unattenuated small signal gain with 15 dB attenuation range. Typical gain flatness is ±0.5 dB, +35 dBm third order intercept point, +22 dBm minimum 1-dB gain compression, and 3.5 dB unattenuated noise figure 4.5 dB at full attenuation. This is only one of a series of microwave controllable amplifiers currently in production.
-
Product
Narrow Band Filters (Single Octave)
NANO-POLE® Series
-
The NANO-POLE® is designed for optimal size, DC consumption, RF power handling, insertion loss, signal purity and linearity. The NANO-POLE® provides a minimum center frequency step size of 10 MHz typically but can be modified based upon request. The NANO-POLE® requires a +3.0 V supply that typically draws 5 mA when not hopping. The supply voltage should be adequately filtered as noise present on this pin will influence the RF signal purity. The NANO-POLE® uses SPI control interface.
-
Product
L Band Satellite over Fiber
-
Transport L Band signals from Satellite Dish to Receiver over Fiber Cable
-
Product
Narrow Band Multiplier
-
*no mechanical tuners*fullband operation*planar design*bias voltage required
-
Product
Narrow Band LNA Family
-
The COMM-connect range of Narrow Band Low Noise Amplifiers can be used to amplify signals in a very wide range of bands. The amplifiers comes equipped with a SMA connectors, for easy installation. Mechanical mounting is made easy by mounting flaps protruding the casing.
-
Product
Narrow Band Filters (Single Octave)
MINI-POLE® Series
-
The MINI-POLE® Series of tunable filters is optimized for size, RF power handling, low distortion, and exceptional selectivity. The product line includes several standard designs in various bands to support a myriad of applications. Approximate performance is summarized in the MINI-POLE Series Selection Guide.
-
Product
DC Blocking L-Band Splitter Combiner
PD5930
-
INSTOCK Wireless Components, Inc
PD5930 is an IP67 outdoor, weather resistant, DC blocking, three way, RF broadband, 50 ohm, power divider, power combiner furnished with TNC coaxial connectors. The passive Wilkinson design passes RF, 10 MHz and DC current through one port, typically for powering an active antenna, with the other ports blocking DC. Max voltage rating at the DC blocked ports is 50 VDC. All wireless band applications in the frequency range from 698 to 2700 MHz are covered with best in class RF performance. The RoHS compliant PD5930 is a bidirectional device capable of 40 W max microwave input power level in both power splitter and combiner apps. See 3 way power divider input rating tables for additional power handling info.
-
Product
Full W-Band Power Amplifier
SBP-7531142515-1010-E1
-
For communication and radar applications, SAGE Millimeter has released a new full W-Band power amplifier. Model SBP-7531142515-1010-E1 is a power amplifier with a typical small signal gain of 25 dB and a nominal output power of +15 dBm across the frequency range of 75 to 110 GHz. The DC power requirement for the amplifier is +15 VDC/190 mA. The mechanical configuration offers an in-line structure with WR-10 waveguides and UG-387/U-M flanges. Other port configurations, such as with 1 mm connectors or a right angle structure with WR-10 waveguides, are also available under different model numbers. Features include: Full Band, High Gain, High Output Power.
-
Product
DC Blocking L-Band Splitter Combiner
PD5980
-
INSTOCK Wireless Components, Inc
PD5980 is an IP67 outdoor, weather resistant, DC blocking, eight way, RF broadband, 50 ohm, power divider, power combiner furnished with TNC coaxial connectors. The passive Wilkinson design passes RF, 10 MHz and DC current through one port, typically for powering an active antenna, with the other ports blocking DC. Max voltage rating at the DC blocked ports is 50 VDC. All wireless band applications in the frequency range from 698 to 2700 MHz are covered with best in class RF performance. The RoHS compliant PD5980 is a bidirectional device capable of 40 W max microwave input power level in both power splitter and combiner apps. See 8 way power divider input rating tables for additional power handling info.
-
Product
PCI Dual Channel Multi-Band Down Converter
LS-27-D
-
The Lumistar LS-27-D3 TwoChannel Quad Band PCI Down Converter product is a 3rd generation high-density, high performance down converter designed using the sameadvanced technology as in the industry leading LS-25 PCIReceiver. The down-converter converts one or two independent channels of up to four RF frequency bands down to a 70 MHz IF output. The LS-27-D3 is typically used in conjunction with theLumistar LS-35 Series Digital IF Receiver/Combiner to provide one or two independent telemetry receivers, or a dual diversity combining receiver, with up to two multi-mode demodulators and bit synchronizers in a two-slot PCI interface. The number of channels and frequency band designations can be specified at the time of order. Please see the data sheet for the LS-35-R Digital IF Receiver/Combiner for more information.
-
Product
IP67 DC Blocking L-Band Splitter
PD5141
-
INSTOCK Wireless Components, Inc
PD5141 is an IP67 outdoor, weather resistant, DC blocking, four way, RF broadband, 50 ohm, power divider, power combiner furnished with SMA coaxial connectors. The passive Wilkinson design passes RF, 10 MHz and DC current through one port, typically for powering an active antenna, with the other ports blocking DC. Max voltage rating at the DC blocked port is 50 VDC. All wireless band applications in the frequency range from 698 to 2700 MHz are covered with best in class RF performance. The RoHS compliant PD5131 is a bidirectional device capable of 40 W max microwave input power level in both power splitter and combiner apps. See 4 way power divider input rating tables for additional power handling info.
-
Product
Amplifier Modules Band Specific
-
Modules are usually smaller and are usually part of systems. You supply your own DC voltage, make the connections and supply your own DC supply. Modules are available with or without heatsinks and fans. Amplifiers Modules are available in both Broadband and Band-Specific frequencies. Modular design concepts save time and money, and are lightweight, reliable, cost-effective solutions. We are well-known in the industry for successfully adapting our amplifiers or custom designing new solutions to suit each unique project. Please refer to our Adapted & Custom Design Solutions link to begin formulating your performance objectives and other criteria.
-
Product
C-Band Red/Blue-Band Pass MWDM
WD1515/R, WD1515/B
-
Hangzhou Huatai Optic Tech. Co., Ltd.
WD1515/R, WD1515/B is based on mature thin film filtering tech, with wide bandwidth, flatness, low insertion loss and high isolation. It is mainly applied to the combination and separation of C-Band, Red-Band (1547~1563nm) and Blue-Band (1528~1543nm).
-
Product
IP67 DC Blocking L-Band Splitter
PD5041
-
INSTOCK Wireless Components, Inc
PD5041 is an IP67 outdoor, weather resistant, DC blocking, four way, RF broadband, 50 ohm, power divider, power combiner furnished with N type coaxial connectors. The passive Wilkinson design passes RF, 10 MHz and DC current through one port, typically for powering an active antenna, with the other ports blocking DC. Max voltage rating at the DC blocked ports is 50 VDC. All wireless band applications in the frequency range from 698 to 2700 MHz are covered with best in class RF performance. The RoHS compliant PD5041 is a bidirectional device capable of 40 W max microwave input power level in both power splitter and combiner apps. See 4 way power divider input rating tables for additional power handling info.
-
Product
L Band Splitter, DC Block All Ports
PD5082
-
INSTOCK Wireless Components, Inc
Wideband Frequency (698 - 2700 MHz)Low Insertion Loss (0.6 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.15 : 1 avg)50 VDC maximum on DC block portsTri Alloy Type N Female (Jack) Low PIM
-
Product
L Band Splitter, DC Block All Ports
PD5022
-
INSTOCK Wireless Components, Inc
Wideband Frequency (698 - 2700 MHz)Low Insertion Loss (0.2 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)50 VDC maximum on DC block portsTri Alloy Type N Female (Jack) Low PIM
-
Product
Multi-Band Imaging
-
Bodkin Design & Engineering, llc
A multi-band camera provides high-resolution, co-registered visible and infrared imagery through a common aperture telescope, unlike conventional visible or infrared cameras that provide image data in limited wavelength bands. Bodkin Design has created the Omnispotter multi spectral camera to enable the user to better discriminate targets from both background and decoys by blending color images with information from the IR band. The images obtained from this system penetrate darkness, camouflage, smoke and clutter better then either visible or IR images could alone.
-
Product
Low Noise Triple Band Voltage Controlled Oscillator
-
This Low Noise Triple Band Voltage Controlled Oscillator was designed to meet a specific customer requirement. The VCO cover the 3300 to 4700 MHz frequency range in three bands. The output power is +9 to +12 dBm with an integrated buffer amplifier to minimize load pulling. The three bands are selected using standard TTL control.
-
Product
Wide Band Transcorders
WBT Series
-
A fully self-contained RF recording and playback system. A single unit can record up to 40 MHz of RF spectrum between 50 MHz and 6 GHz. The recorded data is streamed to a high-speed, internal 1TB solid state drive. The data files are an industry standard open format VRT and can be played back anywhere within the same tuning range at the same recorded power level without additional equipment.
-
Product
2-In-1 Wi-Fi Tri-Band MIMO Antenna, Covering 2.4/5/6GHz Bands, Support Wi-Fi 6E/7, IP67
AIW-514
-
2-in-1 WiFi Tri-band MIMO antennaDipole antenna with omni-directional radiation patternCovering 2.4GHz/5GHz/6GHz bandsSupport latest Wi-Fi6E/7Screw MountRP-SMA male connectorIP67 waterproof resistant for outdoor
-
Product
2-In-1 Wi-Fi Tri-Band MIMO Antenna, Covering 2.4/5/6GHz Bands, Support Wi-Fi 6E/7
AIW-515
-
2-in-1 WiFi Tri-band MIMO antenna, covering 2.4GHz/5GHz/6GHz bandsSupport latest Wi-Fi6E/7PIFA antenna with omni-directional radiation patternMagnetic/Adhesive MountRP-SMA male connectorIP67 waterproof resistant for outdoor
-
Product
Wide band Directional Power Meter
RF ONE 3029
-
The RF One Power Meter is a very versatile instrument covering both analog and digital carriers in an extremely wide frequency range from 30MHz to 6GHz.
-
Product
2 kHz C Band Fast Swept Tunable Laser Source
CA92050-KT
-
The CA92050-KT 2 kHz fast swept tunable laser modules offer superior performance for the test of Fiber Vibration Sensing, DWDM components, AWG , WSS, OPM components, Fiber sensing( especially for vibration fiber sensing application) , optical amplifiers, and other general purpose of fiber optical test and measurement with high wavelength resolution applications.
-
Product
C+L Band Broadband Light Source
OPTOWARE-B200
-
Bench top ASE broadband source system with built-in ASE source module has particularities that it can be operated easily and enables its output spectral feature changed variously by controlling pump LDs inside the module. The output of ASE source can be set to the customized feature by controlling the output power of embedded pump LD individually through the provided program. In case optimum ASE output features such as wide broadband (>80nm@-10dBm/nm) and stable output power (<0.02dB) is needed, it is made up so that the provided Default mode along with User mode can be chosen and set up. Through the micro processor and FPGA inside, more stable application is possible by combining the real-time monitoring of output power and pump LD status with the high speed feedback routine.
-
Product
L Band Splitter, DC Block All Ports
PD5062
-
INSTOCK Wireless Components, Inc
Wideband Frequency (698 - 2700 MHz)Low Insertion Loss (0.5 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.15 : 1 avg)50 VDC maximum on DC block portsTri Alloy Type N Female (Jack) Low PIM
-
Product
IP67 DC Blocking L-Band Splitter
PD5121
-
INSTOCK Wireless Components, Inc
PD5121 is an IP67 outdoor, weather resistant, DC blocking, two way, RF broadband, 50 ohm, power divider, power combiner furnished with SMA coaxial connectors. The passive Wilkinson design passes RF, 10 MHz and DC current through one port, typically for powering an active antenna, with the other port blocking DC. Max voltage rating at the DC blocked port is 50 VDC. All wireless band applications in the frequency range from 698 to 2700 MHz are covered with best in class RF performance. The RoHS compliant PD5121 is a bidirectional device capable of 40 W max microwave input power level in both power splitter and combiner apps. See 2 way power divider input rating tables for additional power handling info.
-
Product
Amplifier Systems Band Specific
-
Systems are complete. They plug into an outlet and are ready to go. Our standard systems are 3U, which is 5.25″ and 5U, 8.75″. Systems are available with or without IEEE-488, RS-232 and Ethernet connectivity. Amplifiers Systems are available in both Broadband and Band-Specific frequencies. We are well-known in the industry for successfully adapting our amplifiers or custom designing new solutions to suit each unique project. Please refer to our Adapted & Custom Design Solutions link to begin formulating your performance objectives and other criteria.
-
Product
Schottky Barrier Bridge Quads
-
SemiGen’s Silicon Schottky Diodes are designed for applications through 40Ghz. The special process technology utilizes various metal schemes to provide excellent performance of Low, Medium, and High Barrier applications. The end result is a low resistance diode with tightly controlled capacitance which allows for optimum performance. Low conversation loss and superior TSS make these diodes ideal for detector / mixer applications with frequency ranges from S band to Ka band as well as modulators, lower power limiters and high speed switches.
