Bridge Amplifiers
Increase a transducers signal to measurable levels.
-
Product
Load Cell Amplifier Signal Conditioner with DB9 Connectors
MODEL LCA-9PC
-
The LCA-9PC Module provides low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-9PC comes with DB9 male and female connectors, which require soldering to user-furnished mating female or male wire connectors. On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film otentiometers.The units can be operated next to the sensor with 4-wire hookup or at distances up to 1 km (3300 feet) with 6-wire hookup. An onboard 87.325 kΩ resistor allows easy shunt calibration at the push of a button. Provision is also made for a user-furnished calibration resistor. Power requirements are 11.8 to 26V DC with load currents from 10 to 60 mA, the latter applying when the unit provides 10V DC excitation to a 350 ohm load cell and delivers a 20 mA analog output.
-
Product
Low Noise Amplifier (DC Powered)
-
RF Lambda’s DC low noise amplifiers (LNA) are broadband and offer low noise figure high IP3. Hermetically sealed options are available upon request.
-
Product
Microwave Amplifiers
MShU Series
-
*Ultrawide Operating Frequency Range*Small Size*Low Noise Figure*Low Power Consumption
-
Product
RF Amplifiers Bias Controllers
-
RF amplifier bias controllers generate a regulated drain voltage and actively adjusts the gate voltage of an external amplifier to achieve constant bias current. It can be used to bias any enhancement and depletion type amplifier operating in Class-A regime with drain voltages (VDRAIN) as specified. These devices achieve excellent bias stability over supply, temperature and process variations, and eliminates the required calibration procedures used to prevent RF performance degradation due to such variations.
-
Product
GN Range Broadband Power Amplifiers 100 KHZ - 200 MHZ
GN Series
-
Class A solid stateBroadband (instantaneous single band): 100 kHz 200 MHzTypical output power : 500 W CWLinear output power (1 dB compression) guaranted with harmonics <-20dBc:P1dB > 450 W and H < -20 dBc up to 100 MHz andP1dB > 180 W and H < -20 dBc from 100 MHz to 200Air cooling: self contained fansCan operate in full mismatch conditions without damageReliable, efficient and robust19" Rack3 years standard warranty
-
Product
Single Phase Lock-In Amplifier
SR510
-
Stanford Research Systems, Inc.
The SR510 and SR530 are analog lock-in amplifiers which can measure AC signals as small as nanovolts in the presence of much larger noise levels. Both the single phase SR510 and the dual phase SR530 have low-noise voltage and current inputs, high dynamic reserve, two stages of time constants, and an internal oscillator.
-
-
Product
Test & Measurement Instrument Amplifiers
MPA-series
-
The MPA-series Test & Measurement Instrument Amplifiers are based on state-of-the-art GaN PA modules and operate from 0.7 to 26.5 GHz (multiple frequency options are available). They provide High continuous power across the band, high linearity for wideband communications testing, have variable gain adjustment and a high-resolution display shows amplifier status. Amplifiers offer a wide range of application-specific requirements including simultaneous high-power, wide bandwidth, low harmonic power and high linearity.
-
Product
RF & Microwave Broadband Amplifiers
-
SHF Communication Technologies AG
SHF has been active in the design and production of broadband RF-microwave amplifier. The outstanding performance makes our amplifiers suitable for a wide variety of applications in R&D. This includes not only optical communications, but also satellite communications, high-speed pulse experiments, data transmission, quantum communication, radar and antenna measurements.
-
Product
Converter Signal Amplifier – 0…10 Vdc – DIN Rail
HD978TR4
-
Configurable signal converter amplifier with 0…10Vdc (10…0Vdc) output. Input range -10 ..+60 mVdc. Standard configuration 0…20 mVdc.
-
Product
MT Range Broadband Power Amplifiers 80 MHZ - 1000 MHZ
MT Series
-
Class A solid stateBroadband (instantaneous single band): 80 MHz 1000 MHzTypical output power : 100 W CWLinear output power (1 dB compression) guaranted with harmonics <-20dBc:P1dB > 100 W and H < -20 dBc up to 450 MHz andP1dB > 65 W and H < -20 dBc from 450 MHz to 1000 MHzAir cooling: self contained fansCan operate in full mismatch conditions without damageUpgradable to MT 200 possibleReliable, efficient and robust19" Rack3 years standard warranty
-
Product
GaAs pHEMT MMIC Power Amplifier, DC - 28 GHz
HMC994APM5E
-
The HMC994APM 5E is a GaAs pHEMT MMIC Distributed Wideband Power Amplifier which operates between DC and 28 GHz. The amplifier provides 15 dB of gain, +29 dBm of saturated output power, and 25% PAE from a +10V supply. With up to +38 dBm Output IP 3 the HMC994APM 5E is ideal for high linearity applications in military and space as well as test equipment where high order modulations are used. The HMC994APM 5E exhibits a positive gain slope from 2 to 20 GHz making it ideal for EW , ECM, and test equipment applications. The HMC994APM5E amplifier I/Os are internally matched to 50 Ohms and is packaged in a leadless QFN 5x5 mm surface mount package.
-
Product
FTTx PON Optical Amplifier (1540~1563nm)
HA5800B (2RU)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
HA5800B (2RU) series is a low noise, high performance, FTTP high power, multi-ports optical amplifier with gain spectrum band within 1540~1563nm. Each output port for optical amplifier has built-in well-performed CWDM. Every external up-link optical port of optical amplifier can connect with OLT PON port very conveniently. Each 1550nm (CATV)'s output optical port multiplex 1310/1490n's data stream, in order to reduce the quantity of the component and improve the index and reliability of the system.
-
Product
Precision Op Amplifiers (Vos <1mV & TCVos<2uV/C)
-
Analog Devices' broad range of precision amplifiers provides industry-leading support to designers in need of traditional trimmed and zero-drift amplifier technology. Our precision amplifier family helps preserve the accuracy of dc information in an incoming signal with low offset voltage (VOS < 1 mV) and low temperature drift characteristics (TCVOS < 2 V/C).
-
Product
Panel-mounted Voltage Power Amplifier
PAV120Bi
-
PAV120Bi is specially designed for R&D of power system simulation. It is adapt to various capacitive and inductive load. It is with 6 channels voltage outputs, each channel with 120V/60VA maximum output.
-
Product
Microwave Power Amplifier 1/4 Watt, 10 MHz to 40 GHz
GT-1040A
-
The Spanawave/Giga-tronics GT-1040A Microwave Power Amplifier incorporates broadband MMIC-based architecture. These state-of-the-art amplifiers are based on solid-state parallel MMIC design with exceptionally wide bandwidth and high power. The unique circuit topology is highly reliable, with performance that excels where extremes of bandwidth and power are demanded.
-
Product
Components - Low Noise Amplifiers (FLNA)
FLNA series
-
Farran's FLNA series low noise amplifiers are constructed with discrete or MMIC pHEMT devices that operate over the frequency range 18 to 110 GHz. These amplifiers are specifically designed for low noise applications.The amplifiers are offered in two categories: standard and custom-built. The custom-built amplifiers are offered in various RF interfaces, including standard waveguide or coaxial connectors, for convenient system integration.
-
Product
Monitor Unit For PAV Series 4-Quadrant Power Amplifier Monitor
-
The 4-Quadrant Power amplifier monitor unit is an optional unit of the PAV series of 4-quadrant amplifiers, which can be assembled into the cabinet.
-
Product
High-Voltage Amplifiers
-
Power amplifiers are a must in applications requiring both complex signals as well as high voltage throughput. However, this is uncommon in high performance instrumentation, therefore an external amplification device must be used. In these cases, a high voltage amplifier is used to increase the size of a signal by some factor.
-
Product
Rail-to-Rail Op Amplifiers
-
Analog Devices high speed (> 50 MHz) rail-to-rail op amps enable you to operate at lower supply voltages, swing closer to the rails, and provide wider dynamic range. Featuring a portfolio with a wide variety of op amps, including both rail-to-rail input/output as well as just rail-to-rail output, ADI provides the widest portfolio of leading edge products available on the market. Whether it is wide bandwidth, high slew rate or low distortion, or rail to rail, no one sets more performance standards for next generation designs than Analog Devices.
-
Product
Gain Block Amplifiers
-
RF gain block amplifier from Pasternack is featured in our extensive in-stock RF amplifier selection. Our connectorized gain block RF amplifier uses SMA connectors. This SMA gain block amplifier has a minimum frequency of 10 MHz, a maximum frequency of 3 GHz and a typical gain of 20 dB.
-
Product
Basic Quad K-Type Analog Thermocouple Amplifier
SEN-30103-K1
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
Automotive Audio Power Amplifiers
-
ST is the recognized leader in automotive power amplifiers. Our car audio amplifiers provide the traditional clean and powerful sound that users have come to expect, as well as all the protection and safety features needed to make our devices robust in an automotive environment.
-
Product
Ultra-broadband Power Amplifier Systems
-
Chengdu KeyLink Microwave Technology Co., Ltd.
Keylink provides ultra-broadband power amplifier systems in rack-mounted configuration with output power capacity from 50-Watt to 2000-Watt for applications including EMC testing, communications, and TWT replacement.
-
Product
1×6 Video Distribution Amplifier
VDA206 S-Video
-
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.
-
Product
Pulsed Injection Locked IMPATT Amplifiers
-
Pulsed injection locked amplifier incorporates IMPATT diode, ferrite input/output isolators, circulators, and pulse modulator. Only DC power supply, RF input signal, and external trigger signal are required to operate amplifier. Output phase noise parameters are very close to the noise parameters of the input RF signal.
-
Product
RF High Power Broadband Amplifiers
-
Chengdu KeyLink Microwave Technology Co., Ltd.
Broadband amplifiers of KeyLink have exceptional RF and Microwave performance. These RF broadband amplifiers(wideband amplifiers) are available in wide frequency bands from 1 MHz to 18 GHz. Power levels for octave and multi-octave designs range from 1 watts to over 1000 watts. Applications of these broadband RF amplifiers range from radar, jamming, communication to test and measurement.
-
Product
Low Voltage DC / Battery Powered High Voltage Amplifiers
WMA-005 And WMA-005LF
-
The Falco Systems WMA-005 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 3mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-005LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.1mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
Product
Load Cell Amplifier Signal Conditioner with Removeable Terminals
MODEL LCA-RTC
-
The LCA-RTC Module provide low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-RTC comes with removable screw-clamp terminal connectors, which accept wires without soldering.On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film potentiometers.The units can be operated next to the sensor with 4-wire hookup or at distances up to 1 km (3300 feet) with 6-wire hookup. An onboard 87.325 kΩ resistor allows easy shunt calibration at the push of a button. Provision is also made for a user-furnished calibration resistor. Power requirements are 11.8 to 26V DC with load currents from 10 to 60 mA, the latter applying when the unit provides 10V DC excitation to a 350 ohm load cell and delivers a 20 mA analog output.
-
Product
Saluki SE1201 DSP Lock-In Amplifier
-
SE1201 Small-sized Digital Lock-in Amplifier provides an excellent performance within its bandwidth from 50 mHz to 120 kHz. With the high-speed 4-core architecture, high-precision ADC and excellent analog performance, SE1201 can easily detect the phase and the magnitude of weak signals overwhelmed by various large noise. The performance of SE1201 is as good as other lock-in amplifiers brands, even better in some certain parameters, such as measurement accuracy, operating bandwidth, which meets the needs of scientific research and industrial application well.
