Conductance
See Also: Battery Conductance Testers
-
Product
Battery Conductance Tester
BT-3918
-
Kongter Test & Measurement Co., Limited
The excellent performance of BT-3918 battery conductance tester will help you pick out the weak batteries and ensure battery performance in short time measurement. This test of battery internal resistance or battery conductance is essential for stationary batteries. It is also recommended by latest regulation of IEEE 450, IEEE 1188 and IEEE 1106.
-
Product
Software
Conductance Measurement and Analysis
-
Materials Development Corporation
MDC uses conductance to give a complete picture of MOS devices as well as to correct for series resistance effects. MDC C-V plotters use conductance and capacitance measurements to plot true device capacitance and depletion region conductance.
-
Product
12V Conductance Batter Tester
MBT100
-
Tests 12V starting/charging systems, including flooded lead acid, AGM, and gel cell batteries. Eliminate tester input errors by choosing between automotive/truck battery or small automotive type batteries.
-
Product
Advanced Battery Conductance/Electrical System Tester
PBT Series
-
Building upon the success of the PBT-100, the first battery conductance tester built for the professional technician's toolbox, the PBT-200 offers these additional capabilities: Shows available power in CCA in addition to condition and voltage. Bad Cell Detection. Advanced Starter Testing: Down arrow displays the captured low voltage from cranking the engine for simple starter analysis.
-
Product
Low Temperature Gas Source
-
Get a low-cost means to introduce a gas without thermal pre-cracking using Veeco’s low-temperature gas source for molecular beam epitaxy (MBE) systems. The source features a large conductance tube for fast gas switching and a diffuser end plate for good growth uniformity. It is an ideal gas injector for CBr4 for carbon doping in GaAs and NH3 for GaN growth, as well as any other gases that do not require thermal pre-cracking. Enhance system capabilities further by combining the source on one mounting flange with an Atomic Hydrogen Source or 5cc Dopant Source.
-
Product
Fixed-Point C6455 DSP Module
FMC645
-
Sundance Multiprocessor Technology Ltd.
The FMC645 is a Digital Signal Processor FMC daughter card based on the Texas Instruments TMS320C6455 device. The FMC645 daughter card is mechanically and electrically compliant with the FMC standard (ANSI/VITA 57.1), has a high-pin count connector and can be used in a conduction cooled environment. This FMC is equipped with power supply and temperature monitoring and offers several power-down modes to switch off unused functions and peripheral interfaces.
-
Product
Transient Limiters
-
Transient limiter LIT-153A and LIT-930A protects a spectrum analyzer input from high-level transients from the line impedance stabilization networks during EMC conducted emissions testing. It has a combined frequency range of 9 kHz to 30 MHz. The built in high pass filter helps reduce 50/60 Hz line feed through. (see application notes)
-
Product
Interface
RQVME2-1553
-
The RQVME2-1553 provides new levels of performance and flexibility for MIL-STD-1553A and B Notice II on the VMEbus. Available in commercial, industrial and conductively cooled versions with one, two or four dual-redundant channels, the RQVME2-1553 includes advanced API (Application Programming Interface) software that reduces application development time.
-
Product
Capacitive sensors
-
Capacitive sensors can detect metallic, non-metallic, transparent, opaque, liquid and solid, conductive and non-conductive substances reliably without the need for contact. They are thus well suited to detect a diverse objects or also bulk goods and liquids.
-
Product
VPX Development Systems
-
development system with Backplane Profile BKP6-CEN06-11.2.5-n. Specifically supports OpenVPX and VPX REDI 6U convection or conduction cooled boards and modules.
-
Product
Resistivity Meter for Concrete
Ohmcorr Test System™
-
OhmCorr has two probes spaced 1.97" (5cm) apart which are placed in holes drilled to a depth of 3/8th" (8mm) and filled with conductive gel. The direct digital read-out of resistivity is displayed on the LCD when the control switch is activated. OhmCorr and CorMap, when used together, provide an economical and sound diagnostic system of corrosion in reinforced concrete.
-
Product
ESD Ground Point
EGP-020
-
The EGP-020 ESD Ground Point is a convenient mechanical socket that can be mounted on to any equipment frame for equal-potential bonding to the equipment. The 4 mm socket is not insulated, made of lathed brass, nickel-plated, for use as grounding socket.The EGP-020 is designed to be mounted on an unpainted conductive surface.
-
Product
Chroma Milliohm Meters
-
Chroma Systems Solutions, Inc.
The Chroma 16502 Milliohm Meter is Chroma’s newest digital Milliohm Meter. 0.001mΩ~1.9999MΩ wide measurement range. DC, Pulsed, and Dry-circuit test current driving modes, enable the Chroma 16502 can be properly used in DC resistance measurement for various inductive components (coil, choke, and transformer winding etc.), cable, metallic contact (connector, relay switch etc.) and conduction materials.
-
Product
PH Meters
-
TES Electrical Electronic Corp.
pH, mV, Conductivity, TDS Resistivity Salinity Concentration and Temperature measurement functions
-
Product
Pin Grips For Flat Specimens
-
Pin grips are very user friendly and are designed for conducting tensile tests of hard metal plate specimens that are difficult to grip. Specimens are held within the grips by passing pins through holes in the specimens.
-
Product
Hydrofluoric Acid Monitor
CM-200A/210A
-
The CM-200A/210A hydrofluoric acid monitors have been developed specifically to meet the stringent demands of semiconductor manufacturing. The CM-200A/210A provides a real time read-out of hydrofluoric acid concentration by measuring the electric conductivity of the sample solution. These superior units offer high repeatability even at low concentrations. The CM-200A/210A can be used for a variety of purposes ranging from monitoring etched wafer cleaning processes to any other industrial application of hydrofluoric acid.
-
Product
PXI High Density MUX BRIC, 8-Chan, 80-Pole
40-570-114
-
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
Product
Benchtop Multi-Parameter Water Quality Meters
-
Labodam benchtop multi-parameter water quality meters come with different measurement modes for quality and testing of water on different parameters such as pH, conductivity, TDS, salinity, and resistivity content from the test sample.
-
Product
PXI High Density MUX BRIC, 6-Chan, 80-Pole
40-570-113
-
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
Product
DX4015
-
The DX4015 empowers professionals to monitor gases in environments that have typically been challenging to conduct measurements. Thanks to its heated sample cell, the DX4015 can be used in humid conditions – with exceptionally low detection limits.
-
Product
Portable Thermal Conductivity Analyzer
CI2100-RQD
-
Shanghai ChangAi Electronic Science & Technology Co.,Ltd
CI2100-RQD portable thermal conductivity analyzer adopts imported high performance intelligent thermal conductivity sensor as measuring unit, which is based on microprocessor. It can test H2 concentration correctly in N2 and H2 mixed gases in a short time. - See more at: http://en.ci-ele.com/dcb675d2-4e33-4eb9-33a0-60edf78c9348/efb4c1eb-f4f5-70af-3ddd-ba6c1066c3fa.shtml#sthash.lXHNyKR1.dpuf
-
Product
Field thermal needle system for thermal resistivity / conductivity measurement
FTN01
-
Hukseflux Thermal Sensors B.V.
The FTN01 Field Thermal Needle System allows performing fast, on-site measurements of the thermal resistivity or conductivity of soils, in particular around the typical depth of burial of high voltage cables. FTN01 is designed with a focus on robustness and saving time, while still offering sufficient accuracy for typical field measurements. The sensor is a Non-Steady-State Probe (NSSP), TP09, which is mounted at the tip of the Lance LN01. The system is operated using a hand-held Control and Readout Unit CRU01.
-
Product
Non-contact Measurement Wafer Sorting System (Belt Drive Tranceportation)
NC-6800
-
*Non-contact measurement of resistivity, thickness and conductivity (P/N)*Number of cassette station can be changed by customers request*Eddy current method for resistivity, Electric capacitance method for wafer thickness*Temperature correction for silicon wafer function
-
Product
Capacitance Bridge
1621
-
The GenRad1621 Capacitance Measurement system is a completely self-contained system capable of capacitance measurements in increments as small as 0.1 aF (10-4 pF) and conductance measurements in increments as small as 100 aU (10-7 U; equivalent to a shunt resistance of 1010 M). Measurements are three terminal, with 2- or 3-terminal connection, and provision is also made for the connection of an external standard for comparison measurements.
-
Product
Silver Ball Matrix Sockets
-
SM Contact is a unique contact that has precise silver balls held together by a proprietary conductive formulation. These conductive columns (diameter optimized for 50 ohm impedance) are suspended in a non-conductive flexible elastomer substrate with a patented solid core for enhanced durability and reliable performance over time, temperature and cycles. This flexible substrate is very compliant and resilient and enables the conductive columns to revert back to original shape when the force is removed. Solutions are available for 0.25mm to 1.27mm LGA, BGA, QFN, CSP, POP, WLP and other packages. The silver ball matrix contact technology is also available with a protective plunger matrix (a gold plated copper cylinder) that sits on top of the conductive columns. This plunger matrix protects the conductive column from contamination from various solder ball interfaces. A quickly replaceable plunger matrix enables minimal downtime during final production test. The product family code for this line of sockets is SMP.
-
Product
Water quality profiler with optical fast DO sensor
AAQ-RINKO
-
The water quality profiler, AAQ 1183 has been redesigned as AAQ-RINKO with an optical fast response (63% response in water, 0.4 s) DO sensor, RINKO. Conventional water quality profilers with a slow response DO sensor require holding the instrument for a certain period at the measurement depths. AAQ-RINKO makes vertical measurements possible with a profiling speed of 0.5 m/s, similar to CTD observation, thereby significantly reducing the observation time. In addition to conductivity, temperature, depth, chlorophyll, turbidity, DO and pH, AAQ-RINKO also enables simultaneous installation of PAR (Photosynthetic Available Radiation) and ORP (Oxidation Reduction Potential) sensors. The processing unit is available in three types in accordance with the observation applications.
-
Product
Comb Generator
CG118
-
The main application of comb generator is to quickly verify 1GHz above radiated emission and conducted emission test setup.And the most important application is 3m chamber and 10m chamber 1GHz above to18GHz with 250MHz frequency spacing for site validation,shielding efficiency. reference signal source Noise Generators Signal Generators
-
Product
Artificial Power Network
KH3765
-
Beijing KeHuan Century EMC Technology Co,.LTD
The KH3765 artificial power supply network is equipped with the receiver produced by our company to conduct large current conduction interference test. The frequency range of this product is 150KHz-30MHz , the current is 50A , and the AC frequency can reach 0-400Hz . It is widely used and convenient to switch. Compared with similar products on the market, it greatly reduces the operation steps and buys valuable time for your rectification work. This product also provides a standard10AThe interface makes your test more convenient. Meet the requirements of GB-6113 for power supply network.
-
Product
Relaying Current Transformer Analyser
-
*Measures Ratio, Excitation Characteristics, Polarity, Winding Resistance, Remanance, and Insulation Resistance of secondary winding. * Determines Composite Error. * Used to test un-mounted CTs or CTs that are mounted but isolated inside the power system equipment. * Conducts a whole series of tests automatically, thus speeding up the time to commission CTs and relaying systems. * Battery powered test set - light weight & fully portable. * Provides a graphical presentation of the CT excitation characteristics. * Determines the IEC 10/50 knee point and the point of maximum permeability, ANSI 45 degree Slope Point. * Detects shorted turns or insulation problems within the test CT, thus avoiding commissioning of faulty equipment.
-
Product
Immunity
RF coupling
-
is used for the conducted measurement of the immunity according to IEC 62132-4.
