Conductance
See Also: Battery Conductance Testers
-
Product
PXI 3A Power MUX BRIC, 2-Channel, 48-Pole
40-571-002
Multiplexer Module
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
Product
Solidtron Thyristors
-
The Solidtron family of products employ our advanced high voltage thyristors having incredibly fast and predictable turn-on performance as well as remarkably low conduction loss. These key attributes make Solidtron products ideally suited for use in a wide variety of pulsed-power applications where precise turn-on characteristics, reliability and longevity give them distinct advantages in certain applications over tube and spark-gap technology.
-
Product
Leakage Current Tester
TOS3200
-
The Leakage Current Tester TOS3200 is designed to perform leakage current (touch current and protective conductor current) tests on general electrical equipment but not medical electrical equipment.It enables you to conduct tests that conform to the requirements of the applicable IEC, UL, JIS, and other standards, as well as the Electrical Appliance and Material Safety Law. The memory in the main unit stores the 51 types of test conditions laid down in the IEC/JIS standards for information technology equipment, household electrical appliances, audio, video electronic apparatus, luminaires, motor-operated electric tools, and electrical equipment for measurement and control and in the Electrical Appliance and Material Safety Law, thereby enabling you to conduct standard tests with simple panel operation.
-
Product
Carbon Sensor Conductivity Meter
HE-960LC
-
Can measures conductivity of low concentration. Its dual calculation circuits and software, combined with carbon sensors, enable measurements ranging without switching. The HE-960LC can be used as a process concentration meter, and also to monitor changes in the concentration of specified chemicals.
-
Product
Oceanography
-
Explore our range of oceanographic instruments for capturing information about our marine environment. Whether you are conducting short-term studies in coastal areas or embarking on multi-year ocean deployments at depths of thousands of meters, we can help you find the best instrument for your application.
-
Product
PXI 3A Power MUX BRIC, 6-Channel, 48-Pole
40-571-006
Multiplexer Module
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
Product
Compensating Reactor
-
The compensating reactors are accessories for the CTS-12KSA/ACTS-12K Capacitance & Tan Delta Test Set. The use of one or more compensating reactors increases the capacitance that the internal power supply can excite to conduct measurements. As the measuring range of the CTS-12KSA / ACTS 12K exceeds the kVA rating of the internal power supply, one way of using the test set over its entire measuring range is to form a resonant circuit with the test sample. The use of one or more compensating reactors forms partial resonating circuit with the test specimen, thereby reducing the power supply requirement.
-
Product
PXI High Density MUX BRIC, 32-Chan, 20-Pole
40-570-314
Multiplexer Module
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
Product
MemoRail
-
Refers to a line of compact, modular transmitters used for industrial process analytics, specifically designed for monitoring pH, ORP, conductivity, and oxygen in various industries like chemicals, pharmaceuticals, and food/beverage.
-
Product
6U OpenVPX Three Drive Storage Module Family
565x
-
The 565x family of 6U VPX Storage Modules provide the ability to access up to three 2.5” solid state hard drives in a single slot. Conduction and air cooled versions bring high capacity storage array capability to rugged environments.
-
Product
8-Channel 250 MHz A/D with Multiband DDC, Kintex UltraScale FPGA - XMC
Model 71132
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Complete radar and software radio interface solution- Supports Powerful Xilinx Kintex UltraScale FPGAs- Eight 250 MHz 16-bit A/Ds- Eight wideband DDCs (digital downconverters)- 64 multiband DDCs- 5 GB of DDR4 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multimodule synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- VITA 42.0 XMC compatible with switched fabric interfaces- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Ruggedized and conduction cooled versions available
-
Product
Shaft Voltage Tester™ Digital Oscilloscope
AEGIS®
-
Digital Oscilloscope and Multimeter with Conductive Microfiber Probe Tips. Is your motor safe from destructive shaft voltages? For the first time you can get all of the tools to find out in one place. The AEGIS® Shaft Voltage Tester™ Digital Oscilloscope bundle includes the AEGIS-OSC-9100 100 MHz digital osciloscope, shaft voltage probe tips, and a shaft grounding simulator. Armed with these tools, you can quickly and easily find whether your motors are at risk of premature bearing failure due to VFD-produced bearing currents.
-
Product
Conductivity Probe
ACS60-35
-
Knowing the conductivity of liquid samples is a key parameter to control product quality throughout the production process. The optek ACF60 conductivity probe fulfils technical requirements of international regulations for reliable measurements ensuring quality and consistency.
-
Product
Low Temperature Gas Source
-
Get a low-cost means to introduce a gas without thermal pre-cracking using Veeco’s low-temperature gas source for molecular beam epitaxy (MBE) systems. The source features a large conductance tube for fast gas switching and a diffuser end plate for good growth uniformity. It is an ideal gas injector for CBr4 for carbon doping in GaAs and NH3 for GaN growth, as well as any other gases that do not require thermal pre-cracking. Enhance system capabilities further by combining the source on one mounting flange with an Atomic Hydrogen Source or 5cc Dopant Source.
-
Product
Nutrient | Oxygen | PH Sensors: PH Sensors
-
pH (potential Hydrogen) is a measurement of the level of acids and bases in water. Our pH sensors have been used extensively to research ocean acidification, coral reefs, coastal marine biology, and to conduct environmental monitoring.
-
Product
LISNs - Single Phase
-
Com-Power single-phase LISNs cover 9 kHz to 400 MHz in five series — 1x, 2x, 3x, 4x, and 5x — with current ratings from 20 A to 100 A for CISPR 16, ANSI C63.4, MIL-STD 461, DO-160, and CISPR 25 conducted emissions testing.
-
Product
EMC Chambers
-
A specialized, shielded room designed to test electronic devices for radiated and conducted electromagnetic interference (EMI).
-
Product
Superconducting Switches
-
switches back and forth between superconducting and normally conducting state.
-
Product
R.F. Coupler and high Pass Filter
7415-3
-
There are those who disagree with the r.f. conducted susceptibility test setup of Method CS02 of MIL-STD-462. Homemade rigs have sprouted to comply with the coupling capacitor requirement, each with it own disadvantage. Our little Type 7415-3 R.F. Coupler is the answer. A neat little box with BNC connectors and a pair of binding posts, it is rated at 270 V.A.C. at the LINE terminals and 20 volts PMS into the GEN port. Looks good and does a fine job.
-
Product
Cation Conductivity Analyzer
CE800 Series
-
The CE800 Series Analyzers are a family of on-line Cation Conductivity Analyzers. Cation Conductivity is also known as Acid Conductivity and Conductivity After Cation Exchange and is the measure of electrolytic conductivity of a liquid sample after that liquid sample has passed through an ion exchange resin column containing cation resin. The conductivity of makeup water, feedwater and condensate after passing through a colum of strongly acid cation exchanger resin is an important chemical measurment used in steam generating power plants.
-
Product
Wet Sponge Pinhole Detection
-
Wet Sponge Technique: A low voltage is applied to a moist sponge. When the sponge moves over a coating flaw, liquid penetrates to the substrate and completes an electrical circuit, setting off the alarm. The wet sponge technique is suitable for measuring insulating coatings less than 500μm (20mils) on conductive substrates, and is ideal for powder coatings and other coatings where the user does not wish to damage the coating.
-
Product
Conductivity-Resistivity Sensor Electronics and Integral System with PVDF Sensor
2850
-
The Signet 2850 Conductivity/Resistivity Sensor Electronics are available in various configurations for maximum installation flexibility. The universal mount version is for pipe, wall, or tank mounting and enables single or dual (digital versions only) inputs using any standard Signet Conductivity/Resistivity sensor. The threaded j-box version can be used with these same Signet sensors for submersible sensor mounting. It is also available as a combined integral system configuration for in-line mounting and includes a conductivity electrode in a choice of 0.01, 0.1, 1.0, 10.0 or 20.0 cm-1 cell constants. The 2850 is ideal for applications with a conductivity range of 0.055 to 400,000 S or a resistivity range of 18.2 M to 10 k.
-
Product
Miniature Concentric Ring Set
PRF-912B
-
- Measures Surface Resistance from 0.9Ω to 1.0x1012Ω- Approximates Measurements Typically Obtained when using ANSI/ESD STM11.11- Spacing Allows for Measurement Area of 0.32 inches (8.13mm)- Spring Loaded Center Electrode Surrounded by 10 Contact Electrodes- Includes Conductive Rubber Covers- Certificate of Calibration Traceable to NIST included
-
Product
Acoustic Target Impact Localization System
ATILS
-
In peace time, for training purposes, artillery units conduct their frequent target practicing.Both the skills of the gunners and the forward observers need to be improved, their communication cycle to be shortened.Forward observing is a dangerous task during war time, causing a justification to find other ways to localize impacts and adjust fires.Furthermore, the sheer lack of a line of sight, because of topography and/or weather, also thrives the need for other solutions to determine the impact coordinates.
-
Product
Fuorescence LED Illumination System
pE-2
-
The pE-2 is a fluorescence LED illumination system which provides repeatable and controllable light with a choice of 20 different LED peaks. It is perfect for the researcher who has a specific set of tests to conduct. The user can specify a wavelength configuration matched to their particular fluorescence requirements. It is modular, allowing LED wavelengths to be exchanged as requirements vary or additional experiments are added. Manual control is via a remote control pod with instant on/off and intensity control from 0-100%. Additionally, the system is fully integrated under many imaging software packages.
-
Product
EMC Testing
-
Does your product send or receive electromagnetic data? This can be analyzed using various tests. We investigate the interference immunity and emitted interference of simple electrical devices and complex machinery. Our EMC measurements and tests conducted in accordance with standards recognize all activity in the electromagnetic field and ascertain how immune to interference a piece of equipment is. We will also offer guidance on optimizing the product in terms of its EMC properties during the development phase.
-
Product
Glow Wire Test Apparatus
GWT A2
-
GLOW WIRE TESTER (also known as Glow Wire Test Apparatus) is designed to carry out fire hazard testing as specified in IEC 60695-2-10 2000-10. Flammability test is to check the ‘Resistance to Fire’ of electrical insulators that touch directly conducting parts & also parts of insulators. This test is also referred in many other standards such as IS 11000, IS 3854 : 1997 / IS 1293 :1988 / IS 371 :1999 & IS 11000 Pt 2 Sec 1, IEC 60335, IEC 884/94, IEC 60598, IEC 61058, BS 6458, BS EN 60695–2-10,11,12, etc.
-
Product
Centralized Database Infrastructure
-
MITS software receives raw data from the devices and conducts the essential processes of data cleaning, format conversion, and analysis to send to a centralized database infrastructure.
-
Product
TDS Meter For The Pool & Spa Industry
PoolMeter™
-
The “dual” range PoolMeter™ is the perfect instrument for the measurement and control of pools and spas. It is a simple and compact pool water analysis instrument operating on the principal of electrical conductivity.
-
Product
PXI 3A Power MUX BRIC, 3-Channel, 16-Pole
40-571-201
Multiplexer Module
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
