Pickup
-
Product
Vibration Pickup
-
Constructed so that each Piezoelectric element has shear that is proportional to applied acceleration between the poles. It is useful for low frequency vibration measurement even in the environments of large temperature change because of it is hard to be effected by the Pyroelectricity. Furthermore, it is less sensitive to the strain in the base.
-
Product
SECONDARY IGNITION PICKUP
MD75300
-
*Safely acquire high voltage waveforms with this high impedance, active pickup*Works with spark plug wires and coil on plug ignitions with MDAUTOWAVE, AUTOWAVECAMO and MDAUTOWAVE2*Adjustable sensitivity increases waveform acquisition accuracy
-
Product
Probe & Pickup
1035
-
TESCO’s Catalog No. 1035 Probe & Pickup combines the best of communication between a PC and a meter. No longer do you have to disconnect the pickup to reconnect to a PC with this all-in-one device. Save time with less hassle.
-
Product
Piezoelectric Vibration Pickup
PU-8ALT6
-
*Upper outlet*Built-in amplifier*Use up to 150 ℃ enabled
-
-
Product
Piezoelectric Vibration Pickup
PU-671D
-
*Upper outlet*Compliant with waterproof (IPX7) and suitable for high temperature (-10℃ to 150℃)
-
Product
Acceleration Pickup Calibrator
VX-1100A
-
VX-1100 is for a piezoelectric type accelerometer which is widely used for measuring vibration. This compact calibrator is effective for checking operation(sensitivity) sensors before measurement to acquire accurate data.Built-in sensor amplifier and display in one unit allows direct reading of the sensitivity. This calibrator excites the sensor at a frequency of 159 Hz and acceleration of 10 m/s2 rms, and the sensor outputs can be used as calibration signals for a vibration measuring system.
-
Product
Piezoelectric Vibration Pickup
PU-661D
-
*Side outlet type*Waterproof (IPX7) and suitable for*high temperature(-10℃ to 150℃)
-
Product
Optical Pickup for Itron Gen™5 Riva™ Meter
1037-RIV
-
Tesco’s Cat. 1037-RIV is designed to hold the pickup sensor directly above the output location on these new meters. It conforms to the shape of the new meter and secures easily to provide hands free operation.
-
Product
Piezoelectric Vibration Pickup
PU-7ALT6
-
*Upper outlet type*Use in water up to 15 meters*depth enabled
-
Product
Optical Pickup
1037-DTS
-
TESCO introduces a new optical pickup (Catalog No. 1037-DTS) for one way meter communication through the calibration LED found on most solid state meters. The pickup senses infrared pulses from ANSI compliant meters for complete, automatic testing.
-
Product
Piezoelectric Vibration Pickup
PU-6GHT6
-
*High-sensitivity type for sensoring*low-rotation from 0.2Hz
-
-
Product
LoadLooker Ammeter
-
Instead of you manipulating a hinged or clamp-type inductive pick-up, the patented LoadLooker electronically closes the loop for you. Its unique U-shape jaw senses the amperage present between its tines.
-
Product
Short Circuit Finders
-
The ShortSniffer locates short circuits in electronics circuits, projects, and printed circuit boards. * locates PCB shorts under solder mask, under components, and even on inner PCB layers * non-contact (inductive) pickup wand * pinpoint short to within 2mm radius (SS2) * rapid location with audio feedback * "follow the sound to the short" * no need for relative or reference measurements * battery operated * diode clamped current drive, won't harm your circuitry
-
Product
Speed
-
Speed sensors for both indoor and outdoor environments with optinos featuring kits for motos, geartooth pickup, tachometers, and stroboscopes.
-
Product
Speed Pick-up
SU63
-
The Validyne SU63 is an AC inductive speed pick-up used for RPM measurement on high-speed rotating equipment. The SU63 is a tightly-wound coil with a laminated core that can be conveniently mounted on rotating equipment so that the magnetic field of a magnetized nut or part passes through the coil windings. The moving magnetic field produces a voltage within the coil proportional to its rate of change and the strength of the permanent magnetized part. The frequency of this inductive voltage spike is fed into an oscilloscope or counter to determine RPM.
-
Product
Rotating Dual Shaft Torque Sensors
RST SERIES
-
The RST- Series is our low range rotating torque sensors that are available in eleven full scale ranges of 10 through 30K inch pounds. The sensing element incorporates bonded foil strain gages of the highest quality along with coined silver slip ring and silver brushes for data transmission. The WR2, Flexural Natural Frequency, and Torsional Stiffness values as stated in the Dynamic Characteristics box below, are approximate and the tabulated data pertains to the torque pickup only, and does not include the effects of couplings or other rotating masses that would be part of a dynamic system.
-
Product
EZ Tach +Plus Automotive Tachometer
328
-
*Versatile instrument can measure RPM on a wide variety of engines from string trimmers to automotive. *Reads engine revolutions from 0 to 20,000 RPM *Picks up RPM signal wireless or with supplied inductive pickup *Great for setting idle speeds! *Built-in LED Flashlight which can be used while taking measurements *Backlit LCD display *Accuracy +10 RPM
-
Product
Piezoelectric Vibration Pickup
PU-8ANSF
-
*Side outlet*Easy to remove due to cap nut type*Use up to 150 ℃ enabled
-
Product
Charge Converter
CH-6130/6140
-
The CH-6130/6140 charge converter is a simplified type of charge amplifier converting charge signal to voltage.It can be connected directly to an input BNC connector of a CCLD applicable equipment such as FFT analyzer or vibration comparator, enabling direct connection of a charge output pickup without suing a box type amplifier.
-
Product
Lightweight Vehicle Surveillance System
LVSS
-
The skid-based LVSS converts a standard commercial pickup into a rapidly deployable command and control center. Within minutes, a single operator can set up the LVSS and report for full perimeter duty from the comfort of the cab. When it’s time to relocate, the mast and its mounted FLIR cameras, radar, and sensors, stow out of sight for covert transportation.
-
Product
C Series Frequency Input Module
Input/Output Module
The C Series Frequency Input Module is designed to acquire isolated frequency inputs from magnetic pickup sensors, variable reluctance sensors, Hall effect sensors, and other transducers with a frequency output. Additionally, the C Series Frequency Input Module provides isolation, configurable thresholds, selectable filtering, and embedded counter measurement logic. These measurements can be synchronized with other frequency, analog, digital, and counter measurements in a single acquisition.
-
Product
Vibration Analyzers
-
A vibration analyzer measures and assesses the machinery condition using vibration sensors such as accelerometers, displacement probes, and velocity pickups.
-
Product
Measuring Wheel
B20-S
-
Simple and light Measuring Wheel B20-s can measure up to 10,000m at 10cm graduation.The counter is indicated in 5 digits and has reset button. When we use Leak Noise Correlator LC-2500, we need to input the between pick-up sensors.
-
Product
Speed Switch
DR1000
-
Features• Works with remote / external pulse frequency output sensor(NPN, PNP, or Mag Pick-up)• DPDT relay output• Under-speed setpoint adjustment from 0.5-5,000 rpm (at 8 PPR)• Terminal blocks for easy wiring• 115, 230 VAC (50-60 Hz) and 12, 24 VDC power options• Rugged explosion proof / NEMA 4X housing• UL Listed Class I, Div I (C, D) Class II, Div I (E, F, G)
-
Product
AC Susceptibility
-
The AC Susceptometer option uses a small primary excitation coil to apply an AC field to a sample (typically 1mT at frequencies from 0.1 Hz 10000 Hz). A pair of secondary pick-up coils positioned close to the excitation coils are used to detect the sample response.
-
Product
Saluki SE4002 FET Input Preamplifier
-
The SE4002 is a low-noise, ultra-high input impedance preamplifier with excellent common-mode rejection. It is designed to work with any Saluki digital lock-in amplifier. The preamplifier minimizes noise and pickup in the connecting lines and reduces measurement time in noise-limited experiments.
-
Product
Signal Conditioner
SA420
-
Features• Works with a remote / external pulse frequency output sensor(NPN, PNP, or Mag Pick-up)• Accepts wide range of input frequencies 0.01 Hz to 10 kHz• 4-20 mA and 0-10 VDC outputs proportional to shaft speed• Field adjustable calibration• 115, 230 VAC (50-60 Hz) and 12, 24 VDC power options• DIN rail mount
-
Product
High Temperature Magnetic Speed Sensors
-
SPECTEC Innovative Sensor Solutions
High temperature speed sensors (up to 454° C) are sensitive, shock resistant & reliable for high temp applications in harsh environments, such as race car engines and transmissions. SPECTEC's high temperature magnetic speed pickups are used as transmission sensors, engine governors, output shaft sensors and flow meter sensors. SPECTEC's high temperature magnetic pick-ups are standard in 5/8-18, 11/16-24 and 3/4-20, and M18 shell sizes.
