Serial to Parallel
-
Product
Parallel Test Systems
-
Our parallel test systems for research and development are highly flexible in use and easily adaptable to different tasks as well as changing piezoelectric materials and designs.
-
Product
Opto Serial Module
DS-MPE-SER4OPT
-
The DS-MPE-SER4OPT offers 4 RS-232/RS-485 opto-isolated serial ports in a PCIe MiniCard form factor. Each port offers 16C550 compatibility and ultra-deep 256-byte TX/RX FIFOs. Maximum data rates are 1Mbps in RS-232 mode and 10Mbps in RS-485 mode. The board is available preconfigured for 4 RS-232 ports, 4 RS-485 ports, or a combination of 2 RS-232 and 2 RS-485 ports. I/O signals are provided on two miniature latching connectors, with 2 ports per connector.
-
Product
Serial Communications
-
ADLINK remote IO and serial communication cards are suitable for handling multiple digital signal types for IoT and other industrial applications such as facility monitoring, environmental monitoring, and industrial process control.
-
Product
Multi-Port Serial
VEX-142
-
The VXC-142 series card provides two RS-422/RS-485 serial ports. Each port can be configured as either RS-485 for half-duplex or RS-422 for full-duplex communication. It supports for speed up to 115200 bps and supports full-duplex communication.
-
Product
Serial I/O Boards
-
Serial Mode Protocols include Asynchronous, Bisync, SDLC, HDLC, IEEE 802.3, Synchronous Telemetry, Simple Clock/Data ("-SYNC" product line), Di-phase and SPI Interface. Transceiver support RS485, RS422 (V.10), RS232 (V.28), RS423, V.35, RS530, as well as other software selectable mixed protocol modes Up to Eight Independent Serial Channels per Board Synchronous Serial Data Rates up to 10 Mbits/sec Asynchronous Serial Data Rates up to 1 Mbits/sec PMC and cPCI rear I/O support Custom Protocols Available
-
Product
Serial Controller
PMC522
Controller
The PMC522 provides a uniquely effective solution for integrating serial I/O requirements into a VMEbus or CompactPCI system. Implemented on a single PMC card, the PMC522 is fully compatible with the current generation of VMEbus and CPCI single board computers, as well as any special purpose processor that includes a PMC connector.
-
Product
Ethernet Parallel Interface
Model 8113
-
* Provides 12 8CMOSL I/O lines for 3.3 and 5 volt logic.* 10/100 MHz Ethernet Interface with Auto-MDIX capability* Robust hardwired TCP/IP (Raw Socket) communication port prevents flooding, spoofing and injection attacks.* Included RS-232 serial control port for older systems.* Optional I2C port for connection to touchscreen panel or other I2C devices.* Standard board has a horizontal Ethernet connector and 150-pin Digital IO connector on the component side.
-
Product
GPIB Parallel Interface
Model 4803
-
* 4803 Board provides 40 high-power TTL I/O lines that can sink 48 mA or source 24 mA. * Easily interfaces to TTL or CMOS signals and contact closures. * User can configure the data bytes as inputs or outputs.* Transfer data as bits, bytes as data strings or transparently.* Dual GPIB headers support connections to a GPIB Connector/Address Switch Assembly or to a GPIB Flat Ribbon Cable Assembly.* Optional Relay Driver board drives 24-40 relays.
-
Product
Parallel Robots
-
The Omron Quattro robot excels at high-speed applications in packaging, manufacturing, assembly, and material handling.
-
Product
Massively Parallel Board Test System
I7090
In-Circuit Test System
The Keysight i7090 is a massively parallel board test system designed to help PCBA test engineers improve manufacturing efficiency while reducing costs. Unlike traditional in-circuit testers, the i7090 supports up to 20 In-Circuit Test cores in parallel, which means engineers can test multiple Units Under Test (UUTs) simultaneously without the need for multiple systems. This reduces scaling and infrastructure costs and frees up valuable testing space.
-
Product
SAS (Serial Attached SCSI)
-
Serial Attached SCSI (SAS) is a data transfer technology designed to move data to and from storage devices such as disk drives, host bus adapters (HBA), and expanders. SAS is a serialized enhancement and replacement to parallel SCSI. Since SAS ratification in 2004, and it’s move to 6Gbps in 2008, Teledyne LeCroy has continued to support and innovate with it’s industry leading protocol analysis and traffic generation capabilities.
-
Product
cPCI Serial Power Supplies
-
CompactPCI Serial (PICMG CPCI.S-0) has added a number of features and benefits while maintaining backward compatibility to create a foundational spec for serial-based CompactPCI technologies. This includes an updated power supply specification. CompactPCI Serial requires only one +12 V power supply with a maximum power of 79.8 W per 3U module and 171 W per 6U module as well as a 5V stand-by voltage.
-
Product
Wired Serial Device Server
SD-300
-
The Silex SD-300 and SD-310AN are designed to easily connect and share RS-232 serial devices over a wired or wireless network. Industrial automation, building automation, medical devices, security access and control, point of sale devices, LED signs, bar code/label and other specialty printers, or virtually any other device with a serial port can be now be enabled with secure, robust wired or wireless network capability.
-
Product
SATA (Serial ATA)
-
Serial ATA (SATA) is a data transfer technology designed to move data to and from storage devices such as disk drives, ATAPI drives, host bus adapters (HBA), and port multipliers. SATA is a serialized enhancement and replacement to parallel IDE. Since SATA ratification in 2003 and its move to 6Gbps in 2008, Teledyne LeCroy has continued to support and innovate with its industry leading protocol analysis and traffic generation capabilities.
-
Product
Serial to Digital Interface
-
All of ICS's Serial Digital Interfaces are user configurable and let you transfer data as bits, bytes or as strings of bytes. All data lines are high power TTL outputs or floating inputs with pullup resistors for sensing CMOS signals or switch contacts. All interfaces conform to the IEEE-488.2 Standard and are HP-IB compatible.
-
Product
GPIB Serial Interface Boards
-
ICS's GPIB to Serial Interface boards are designed for in-chassis applications. Select boards with transparent data transfer or boards with smart firmware that can add an IEEE-488.2 interface to any serial device
-
Product
USB-485/4, 4-Port, USB, RS485/RS422 Serial Interface Device
778476-94
Serial Interface
The USB‑485/4 interface transforms your USB port into a single asynchronous serial port for communication with RS485 and RS422 devices. You can use a USB‑485/4 port as a standard serial port from your application, including RTS/CTS hardware handshake lines. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
Serial analyzer
-
The Serial analyzer sink decodes analog data on a serial bus to serial data. It can be used to monitor and analyze RS232, RS485, MIDI, DMX or other compatible serial buses. The serial analyzer can monitor up to eight sources. When these sources are in sync (all sources are of one (combined) instrument), all captured data will be displayed in chronological order.
-
Product
Multi-Port Serial
VXC-112iAU
-
The VXC-112 series card provides 2 RS-232 serial ports. It is equipped with a 128-byte hardware FIFO for each port, supports for speed up to 115200 bps and supports full-duplex communication.
-
Product
PICkit Serial Analyzer
DV164122
-
The PICkit Serial Analyzer is a low-cost USB-based tool used to direct communication between a PC and an external serial device. I2C™ - Master, I2C™ - Slave, SPI - Master, USART – Asynchronous, USART – Synchronous, LIN (external hardware required to meet electrical specifications), MICROWIRE.
-
Product
MIPI Camera Serial Interface
CSI
-
Arasan provides a Total MIPI CSI-2 IP Solution supporting two options: MIPI CSI-2 v1.2 for D-PHY physical interface only, and MIPI CSI-2 v1.3 for the new MIPI C-PHY v1.0 and D-PHY v.1.1, v1.2, and a future v2.0. Arasan offers the C-PHY in a combination configuration that supports both C-PHY interfaces and D-PHY interfaces. Our implementation makes efficient use of the high frequency signally pins for a minimal overhead to support both physical interfaces.
-
Product
I-8000 Parallel Data Acquisition Modules
-
ICP DAS I-8000 Parallel Series I/O are high speed cartridge based and come in a multitude of digital and analog configurations. They are communicable via an RS-485 backplane in all of ICP DAS USA's I-8000 & I-87K series rack mount controllers. There are two types of I/O communication bus, parallel bus and serial bus. The parallel bus type I/O modules (high profile I-8K series) are high speed, used only in the PACs including XPAC, WinPAC, iPAC, ViewPAC, etc. And the serial bus type I/O modules (high profile I-87K series) are low speed, used in both PACs including XPAC, WinPAC, iPAC, ViewPAC, etc.
-
Product
SparkFun USB To Serial Breakout
FT232RL
-
This is the SparkFun USB to Serial Breakout for the FT232RL, a small board with a built in USB to serial UART interface. This little breakout is built around the FT232RL IC from FTDI, with an internal oscillator, EEPROM, and a 28-pin SSOP package this is a serious little chip.
-
Product
PXI-8431, 4-Port, RS485/RS422 PXI Serial Interface Module
778985-01
Serial Interface
4-Port, RS485/RS422 PXI Serial Interface Module - The PXI‑8431/4 is a high-performance interface for high-speed communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between 4‑ and 2‑wire transceiver modes for full- and half-duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
Multiprotocol Serial Card
PCIe-ICM-4SM
-
The PCIe-ICM Series are a new family of isolated PCI Express serial communication cards. These PCI Express cards feature a selection of 4 or 2-ports of isolated, software selectable, RS-232, RS-422, and RS-485 serial protocols.
-
Product
PXI-8430, 8-Port, RS232 PXI Serial Interface Module
779536-01
Serial Interface
8-Port, RS232 PXI Serial Interface Module - The PXI‑8430/8 is a high-performance interface for high-speed communication with RS232 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. NI serial interfaces also appear as standard COM ports … for compatibility with programs that use serial communications.
-
Product
8 Channel Serial IndustyPack Card
IP-OctalSerial
-
8 channel serial IndustyPack card with 4 dedicated in and 4 dedicated out channels. Each channel has its own seperate FIFO and state machine
-
Product
*68 POS VHDCI Conn to Eight 9 POS D-SUB, RS 485, 1M
197546-01
Serial Cable
68 POS VHDCI Conn to Eight 9 POS D-SUB, RS 485, 1M
-
Product
Isolated Serial Communication Card
PCI-ICM-1S
-
The PCI-ICM-1S is a single port asynchronous optically isolated serial communication card that can be installed in any 3.3V or 5V PCI slot computer. Data lines are opto-isolated from the computer and from each other to assure communication even when large common mode voltages and noise are imposed.
-
Product
8-Sites Flash Programmer w/Relay Barrier, True Parallel Channels
YAV90FR2
-
The YAV90FR2 or YAM90FR2 is a flash programmer housed in a compact 6TL YAV Module form factor, designed forseamless integration into automated test environments. It incorporates the advanced FlashRunner 2.0 technology fromSMH, enabling efficient programming of microcontrollers, flash memory, and other logic or memory devices. Themodule features flexible connectivity options, with all digital I/O (DIO), programmable voltage lines, and correspondingground lines switchable via integrated relays.
