Timing
See Also: Time, Timers, Time Interval, GPS Time, Time Reference, Time Code, Time Domain, Time Standards, Time Interval Analyzers
-
Product
Seam Fold Test Device
FFR1000
-
This equipment is designed to bend a flexible printed circuit board, which has a high degree of freedom and versatility, and at that time, apply a load to the bending point at the initial stage or each time, and repeat bending and unfolding to confirm the durability.
-
Product
Relaying Current Transformer Analyser
-
*Measures Ratio, Excitation Characteristics, Polarity, Winding Resistance, Remanance, and Insulation Resistance of secondary winding. * Determines Composite Error. * Used to test un-mounted CTs or CTs that are mounted but isolated inside the power system equipment. * Conducts a whole series of tests automatically, thus speeding up the time to commission CTs and relaying systems. * Battery powered test set - light weight & fully portable. * Provides a graphical presentation of the CT excitation characteristics. * Determines the IEC 10/50 knee point and the point of maximum permeability, ANSI 45 degree Slope Point. * Detects shorted turns or insulation problems within the test CT, thus avoiding commissioning of faulty equipment.
-
Product
Central Office Line Simulator
AI-7280
-
The AI-7280 is a highly flexible central office line simulator. It is designed primarily for the testing and verification of common terminal equipment, including standard telephones, Caller ID devices, SMS (Short Message Service) capable equipment, and any device using an analog Tip/Ring interface circuit. Supplied with the TRsSim software for Windows, it can analyze a telephone''s DTMF characteristics, pulse dialing and flash timing, generate various network tones and ringing patterns. Both Type I (on-hook) and Type II (off-hook) Caller ID is supported using either FSK or DTMF data transmission. As an optional component, the TRsSim software can perform SMS testing to either the ETSI protocol 1 or protocol 2 standards.
-
Product
FADEC/EEC Test Platform
-
The FADEC/EEC Test Platform provides a hardware in-the-loop (HIL) closed-loop test environment for dynamic and maintenance testing of full-authority digital engine control (FADEC) and electronic engine control (EEC) units of both rotary- and fixed-wing airframes. The system simulates one or more turbofan engines, including its sensors and actuators for use with the most sophisticated FADECs and EECs on the market. The system delivers repeatable, cost-effective testing in a fraction of the time needed with typical in-house simulation test systems.
-
Product
Energy & Process Monitor
-
Real time monitoring and reportingComposite system with EMS and PEMSDesired reports like, Doff wise, shift wise, count wise, production, energy, UKGSpeed Vs Kw curve, trends, bar graphs, comparisonsAlerts on higher UKG, lesser production, utilization & power fluctuations.Maintenance alerts based on run hours production cost analysis - Cost Audits - Energy Audits
-
Product
Instrument Control & Connectivity Software
-
Connect, Configure, and Automate Your Tools.It shouldn't take a headache to get the most out of your tools. That's why Keysight offers a suite of licenses, libraries, and instrument control software to help you automate workflows and accelerate innovation.From simple connectivity and programmatic control to software integrations and test automation suites, our turnkey solutions mean you can spend more time thriving — and less time toiling with lengthy workarounds.
-
Product
Automation Testing Services
-
QACraft has been one of the leading companies in providing automated testing services for all types of software and applications inclusive of mobile as well as web apps. Our expert team designs the QA strategy to check the various parameters such as functionality, speed, performance, quality, loading time, and much more to give you a detailed report about the same.
-
Product
Logic Analyzer Probe
FS2520
-
The FS2520 is our newest and fastest logic analyzer probe used to test DDR4 DIMM memory. It is designed to work exclusively with 3 Keysight U4164A logic analysis modules operating in either Quad Sample State or Quarter Channel 10GHz timing modes. This gives the user an extremely effective tool for debugging, testing and verifying DDR4 DIMMs running above 4000MT/s. It’s like having a 100 channel scope.
-
Product
Relay Buddy PRO Test Kit
191
-
Relay Buddy is a quick go / no-go tester for the most common automotive relays. With the included adapters, Relay Buddy now tests 5 different relay types and also tests shielded relays. Relay Buddy provides you with an indication of the general health and functioning of the relay switch contacts and coil. It will check the control side of the relay by applying a signal to the relay coil while it checks for proper functioning of the relay contacts. Relay Buddy operates the relay several times during each test session as it watches for consistency in every cycle. Relay Buddy will fail the relay and light the RED LED if any one of the cycles proves unsuccessful during the test session.
-
Product
LED Stroboscopes
-
Our LED stroboscopes use solid-state light sources that are very durable and long lived with no heat generation or drift over time. They feature push button control of all digital functions and pulse width modulation to ensure sharp images at high speeds and aluminum housings.
-
Product
Azure Cosmos DB
-
Azure Cosmos DB is a fully managed NoSQL database service for modern app development. Get guaranteed single-digit millisecond response times and 99.999-percent availability, backed by SLAs, automatic and instant scalability, and open-source APIs for MongoDB and Cassandra. Enjoy fast writes and reads anywhere in the world with with turnkey data replication and multi-region writes. Gain insight over real-time data with no-ETL analytics using Azure Synapse Link for Azure Cosmos DB.
-
Product
Remote Cable Tester for RJ45 RJ11 USB and BNC
REMOTETEST
-
Troubleshoot your wiring problems, quickly and affordably with StarTech.com's REMOTETEST, a Specially designed network wire tester that saves valuable time and effort when testing RJ45, RJ11 and BNC cables.
-
Product
PXIe-6378, 16 AI (16-Bit, 3.5 MS/s/ch), 4 AO, 48 DIO, PXI Multifunction I/O Module
781476-01
-
PXIe, 16 AI (16-Bit, 3.5 MS/s/ch), 4 AO, 48 DIO, PXI Multifunction I/O Module—The PXIe‑6378 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, four 32‑bit counters, and analog and digital triggering. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PXIe‑6378 is ideal for a variety of applications, such as IF digitization; transient recording; ISDN, ADSL, and POTS manufacturing test in the telecom industry; ultrasound and sonar testing; and high-energy physics. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
High Performance Embedded Box IPC
MIC-7000
-
The compact modular PC support i-module expansion to satisfy diverse application requirements. Modular computer reduces lead time for CTOS due to easy configuration and can be widely deployed for factory and machine automation.
-
Product
PXIe-5763, 16-Bit, 500 MS/s, 4-Channel PXI FlexRIO Digitizer
785161-01
-
The PXIe-5763 is a PXI FlexRIO Digitizer that simultaneously samples four channels at 500 MS/s with 16 bits of resolution and features 225 MHz of analog input bandwidth. With over 73 dB of SNR, the PXIe-5763 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA. Available in AC and DC coupled variants, the PXIe-5763 is ideal for both time and frequency domain applications, including radar prototyping, LIDAR, communications, microscopy, OCT, event detection, and particle physics.
-
Product
USB-6346, 8 AI (16-Bit, 500 kS/s), 2 AO (900 kS/s), 24 DIO USB Multifunction I/O Device
785815-01
-
8 AI (16-Bit, 500 kS/s), 2 AO (900 kS/s), 24 DIO USB Multifunction I/O Device - The USB-6346 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, and four 32-bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI-STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB-6346 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Affordable EDXRF Analyzers
NEX QC Series
-
Applied Rigaku Technologies, Inc
NEX QC is the lowest cost variant of a line of affordable benchtop EDXRF spectrometers designed for rapid qualitative and quantitative analysis of elements from sodium (Na) to uranium (U) in solids, liquids, alloys, powders, and thin films. For more demanding applications, or for situations where short analysis time is critical, we recommend the NEX QC+ spectrometer. Employing the next generation silicon detector technology, the enhanced NEX QC+ affords significant improvement in elemental peak resolution and counting statistics.
-
Product
Almanac Time Switch
IM1754
-
Almanac Tme Switch is a real time timer which can be used to switch electrical appliances like street lamps, garden lights, corridor lights, neon signs etc. as per time of the day. The timer has built in Almanac timings fixed in Nonvolatile RAM so that the user does not have to programme the unit from time to time. This Almanac time switch has added advantage over daily dial or weekly timers. Timer provides two outputs to drive contactors of different ratings. These outputs can be used with different combinations to achieve desired output. Timer is provided with manual override facility. Optional detachable external keyboard unit provided to avoid unauthorized access.
-
Product
Unipolar Variable Gain High Speed Amplifier
F70PV
-
The F70PV is a very fast, unipolar, linear amplifier having a variable amplification of 0-10 times and capable of voltage output of +70V. Any functiongenerator or arbitrary waveform generatoror any othe signal source can be used as an input device. The amplifier's output is linear from DC up to ca 10 megahertz range. It can be used in a wide range of high speed applications.
-
Product
USB-6349, 32 AI (16-Bit, 500 kS/s), 2 AO (900 kS/s), 24 DIO USB Multifunction I/O Device
785816-01
-
32 AI (16-Bit, 500 kS/s), 2 AO (900 kS/s), 24 DIO USB Multifunction I/O Device - The USB-6349 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, and four 32-bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI-STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB-6349 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
48-Channel VME Isolated Digital Input Module
V280
-
The V280 is a single-wide, 6U VME module that includes 48 isolated logic inputs. It is available in versions for nominal 5 volt or 24 volt input levels. The V280 has independently programmable rising and falling edge response times to support contact debounce, glitch catching, and DC or AC inputs.
-
Product
NI-9253, 50 kS/s/ch, ±20 mA, 24-Bit, 8-Channel C Series Current Input Module
785989-01
-
50 kS/s/ch, ±20 mA, 24-Bit, 8-Channel C Series Current Input Module - The NI-9253 is an 8-channel analog input module for ComapctDAQ and CompactRIO systems. Each channel provides a ±20 mA input range and 24 bits of resolution at a 50 kS/s sample rate. The NI-9253 has several diagnostic features to ensure your system is operating nominally at all times with open channel detection, power supply detection, and configurable thresholds. The NI-9253 has eight LEDs to indicate the status of each channel and the power supply so that a user in the field can easily validate that the system is operating normally. The NI-9253 also features a number of programmable hardware filters. By choosing the specific Butterworth and comb filters for your application, you can significantly reduce the noise in your system.
-
Product
PXI/PXIe MEMS RF Multiplexer, Quad 4-Channel, 4GHz, 50Ω, MCX
40-878-242
-
The module is based on the latest micro-electromechanical system (MEMS) switching technology and has low insertion loss and VSWR. In addition, MEMS devices have a long operational life of >3 billion operations and benefit from an operating time of <20 μs allowing greater test system throughput. The multiplexers have excellent and repeatable RF characteristics beyond 4 GHz with each path having a nominally equal insertion loss.
-
Product
In Vivo Systems
-
To achieve low minimum detectable activities with count times as fast as one minute.
-
-
Product
PNA-X Measurement Receiver for Antenna Test
N5264B
-
A new industry standard for antenna test with 400,000 point per second data acquisition on all five measurement channels Twice as many receivers available compared to any other antenna receiver on the market Replace existing 8530A and 8360 solutions for a system speed improvement that is 10 times faster Built-in 8510/8530A code emulation software provides a drop-in replacement for existing antenna ranges utilizing an 8530A
-
Product
Vision Software
-
These “all-in-one” software products have been deployed in thousands of installations around the globe, providing advanced tools, design flexibility and system versatility to suit diverse application needs across all industries. Built to run on our smart camera and multi-camera vision systems, our easy-to-use iNspect and Sherlock design platforms save you time and reduce vision development costs without compromising system performance or reliability.
-
Product
Dual-port Isolated CAN Interface Cards
PCI-7841/cPCI-7841
-
The PCI-7841/cPCI-7841 is a Controller Area Network (CAN) interface card. It supports a dual-port CAN's interface that can run independently or bridged at the same time. The built-in CAN controller of this card is Philips SJA1000, which provides bus arbitration and error detection with auto correction and re-transmission function.
-
Product
Circuit Breaker Tester
GDGK-307
-
Chongqing Gold Mechanical & Electrical Equipment Co.,Ltd
1) Closing and opening time measurement of 12 channels2) Max difference of closing or opening time measurement of three phases3) C-O and O-C time measurement4) Rated operation sequence test5) Bounce time and frequency measurement of breaker closing6) Circuit breaker closing and opening speed measurement7) Travel-time, coil current-time curve of circuit breaker operation measurement8) Travel and clearance of circuit breaker measurement9) Variable DC circuit breaker operation power supply10) Closing arc resistance value and connected time measurement11) Closing time and opening time of graphite circuit breaker measurement12) Print test results by internal micro printers
-
Product
Amplifier Modules Broadband
-
Modules are usually smaller and are usually part of systems. You supply your own DC voltage, make the connections and supply your own DC supply. Modules are available with or without heatsinks and fans. Amplifiers Modules are available in both Broadband and Band-Specific frequencies. Modular design concepts save time and money, and are lightweight, reliable, cost-effective solutions. We are well-known in the industry for successfully adapting our amplifiers or custom designing new solutions to suit each unique project. Please refer to our Adapted & Custom Design Solutions link to begin formulating your performance objectives and other criteria.
