-
Product
Square Wave Patterns (Ronchi Gratings/Rulings)
-
Square Wave patterns (Ronchi Gratings/Rulings) have extremely sharp edges. At APPLIED IMAGE, this sharpness is achieved through our unique manufacturing capabilities and processing technologies which produces the sharpest edges available anywhere. Our standard line of Ronchi Gratings is offered on Chrome on Glass (CG) and Photo Paper (RM).The Ronchi rulings are available on other substrate materials such as B270, quartz, BK-7, and White Opal as well as in English frequency metrics (cycles per inch).
-
Product
VLF Test System
BAUR PHG 70 portable
-
Portable, high performance test generator with VLF truesinus technology. The BAUR PHG 70/80 portable VLF test systems are used for cable and cable sheath testing of medium-voltage cables of up to 50 kV and electrical equipment.* 3 voltage shapes in one device: VLF truesinus, VLF square wave and DC voltage* For medium-voltage cables of up to 50 kV operating voltage* Cable testing, fault conditioning, cable sheath testing
-
Product
Single-Channel DC Powered Carrier Demodulator
CD16
-
The CD16 Miniature Carrier Demodulator is designed to deliver a 0 to 5 Vdc output from a variable reluctance transducer and operate from unregulated 9 to 55 Vdc power. A square wave excitation of 5 kHz is furnished to the transducer and the solid state integrated circuit amplifier and demodulator converts the transducer signal to an analog dc output. Zero and Span adjustments are made through access holes in the case.
-
Product
Digital I/O Cards
104-DIO-48E
-
The circuits use an 82C55A PPI with mode 0 supported. Ports A, B and C are buffered with 74ABT245 transceivers and pulled up to 5V. The optional 82C54 has three-sixteen bit down-counters within one chip. These counters are useful for making frequency outputs, measuring frequency of square waves, pulse width outputs, pulse width measurements etc. Software drivers are provided on CD.
-
Product
AC & DC Electronic Load
3270 Series （350V,1875W~22500W）
-
3270 Series is suitable for the step, square and sine wave of the AC Power device test, especially for the uninterruptible power supply UPS, Inverter, fuses, circuit breakers, power regulator AVR, battery, AC / DC power supply / components ... and so on, absolutely is the best test solution in the market.
-
Product
Shock Test Systems
-
Sanwood Environmental Chambers Co ., Ltd.
Is featured with advanced design, high degree of automation and reliability, simple operation and convenient maintenance. The system meets the requirements of both shock and collision test, can perform conventional half-sine wave, post-peak sawtooth wave, square wave and other waveform shock tests.
-
Product
Palm Size Digital Multimeter, Calibrated, 1999 Count, Mean Value, Manual Range, 3.5 Digit
72-7770 CAL D
-
The 72-7770 CAL D from Tenma is a palm sized digital multimeter with 3 3/4 digit LCD. It is 3 1/2digits with steady operations, fashionable design and highly reliable hand held measuring instrument. The meter measures AC/DC voltage, AC/DC current, resistance, temperature, diode and continuity. It is an ideal tool for maintenance. The multimeter features square wave output, data hold, low battery indicator and display backlight, This meter complies with the standards CE, IEC61010, in pollution degree 2, overvoltage category (CAT I 600V, CAT II 300V) and double insulation.
-
Product
Pulse Delay Generators
-
Quantum Composers provides innovation and value to our customers with our diverse family of Precision Pulse Generators. A wide range of pulse generator technology has been created to fit the needs of any budget and application. Our square wave signal generators provide a cost-effective method to create and synchronize multiple sequences, delayed triggering, or any precisely timed series of events.
-
Product
Compact Multi-use Type Rotary Encoder
RP-432Z
-
Compact and economical design for general purpose;ideal for OEM applications5 VDC or 12 VDC operationEasy-to-use output signal connector2-phase and zero mark square wave outputsNine output pulse types to select from.
-
Product
UPG-07 - Ultrasonic Precision Gages - Monochrome
UPG-07 Monochrome
-
PG-07 Series of hand held ultrasonic precision gages are available in 4 models. Our UPG-07 series is the ideal unit to non-destructively test the wall thickness for manufactured parts requiring unprecedented accuracy and resolution. The UPG-07 series utilizes single element transducers and offers a 30 Mhz, square wave pulser, .0001" or 1 micron resolution with the ability to store and re-call 30 unique applications. So if you are measuring light bulbs, plastic bottles, golf clubs, coil steel, thin aluminum, aircraft parts and even pure gold bars, the UPG-07 series is the right choice.
-
Product
Function Generator
FG-281
-
The FG-281 is a function generator using DDS (Direct Digital Synthesis) for superior frequency stability. Possible to output sign wave and square wave at wide oscillation range from 10mHz to 15Mhz. A 10-key keypad provides user-friendly operation even though various functions are available. Possible to memorize 9 kinds of panel settings and they can be recalled easily. RS-232C and GP-IB interfaces are available as standard and enable to be controlled by PC (full remote control).
-
Product
Mini Digital Multimeter
HH2103
-
Basic Accuracy 1.0%. LCD display 2000 count, 12.8mm figure height. Manual Ranging at your choice (19 Range). Higher Voltage test up to AC 750V and DC 1000V. Higher Current test up to 10A. Resistance test up to 2000KΩ. Diode test. Square Wave Signal Injection
-
Product
20 MHZ Arbitrary Waveform Generator
F175 AWG
-
he F175 AWG does not replace our current square wave generator models (F125/165/170/110). It is an arbitrary waveform generator. Its main strength is in producing non-square waves. Of course it is also able to produce square waves but if you only need generate square waves, please look at our other models: F125/165/170/110. We expect to have F175 AWG production boards available in the third quarter of 2009.
-
Product
CPCI or PXI DPFS Board
MS 1830
-
- Configurable Frequency Ranges from 100Hz to 1MHz- Resolution insteps of 0.03Hz- Duty Cycle 50%- Amplitude of the Digital Frequency out : Low – 0.4V max, High – 4.8V min- Rise/Fall Time (for a 15pF Load) is typically 5 ns- Amplitude of the Analog waveform out : Low – 0.4V max, High – 4.8V min- Sinusoidal or Square Wave Output (Configurable)- Differential / Single Ended Output (Configurable)- Frequency on each of the 8 Channels are individually Programmable- Hot Swap Facility for live insertion and removal of the board- Facia plate with Micro Switch Assembly, provided for proper insertion / easy removal of the Board- BNC Connector Interface for Signal Output at the front panel- Each Output Channel is driven by a Cable Driver to drive 8m of Coaxial Cable- Driver interface for Windows XP/VISTA/7 and LINUX OS
-
Product
Variable Tone Generator
-
> 60 Hz to 18 kHz approx> 1.3 VAC P/P> Frequency & Level Pots> Sine or Square Wave> 4.5 x 2.5 x 1.1 inches> 9 volt battery operation
-
Product
10MHz DDS Sine & Square Wave SIGNAL GENERATOR
SG-10
-
Model SG-10 architecture is based on the latest advances in DDS technology. Microprocessor control delivers clean and accurate DC to 10MHz waveforms with frequency accuracy of 0.02% and 0.1 Hz frequency resolution.
-
Product
Frequency Doubling Comb Generator
COMBGEN6DIFF
-
*Differential output - can also provide two separate single ended complementary outputs.*Pulse height of up to +4V peak into 50 ohms, on positive output*Pulse height of up to -4V peak into 50 ohms, on negative output*Rise time < 80pS, FWHM of approximately 120pS*Produces pulse on both edges of input clock, thereby doubling frequency.*Input clock may be sinewave from 50MHz to 2GHz or square wave from 5MHz to 2GHz, producing fundamental comb tooth energy from 10MHz to 4GHz.*Usable energy to >10GHz.*Can drive any load, including short, without damage.*Power Requirements: -12V @ 120mA and +24V @ 80mA
-
Product
Function Generators
-
Waveform : Sine, Triangle, Square, Pulse, Sawtooth, Ramp 0.2Hz-150MHz EXT Frequency Counter(Option : 1:6 GHz or 2.7GHz) Self made insert ASIC Function : Total, RPM, Period, LPF, COUPL(AC/DC), ATT(X10) Fast,High-Resolution, 8Digits LED display Internal or External AM,FM Modulation Internal or External Burst and Linear Sweep Countrol from 1 : 1 to 100:1 TTL/CMOS Leveled Square Wave Output Maximum Attenuation of 20 dB cna be obtained Output impedance : 50 INPUT SENSITMTYKHz Range : 100mVms, MHz Range : 300mVms SWEEP WIDTH : Variable from 1:1 -100:1 RATE : 0.5Hz - 50Hz(20ms-2s) INTERNAL : Linear Bilt-in 5digits Green LED display
-
Product
Demonstration Board
SAMPULSE20x2
-
The SAMPULSE20x2 is a demonstration board for the Furaxa SiGe3 30GHz sampler/pulser IC. The SIGe3 IC is a dual channel sampler pulser chip, and the SAMPULSE20x2 demonstration board contains two 2.4mm combined TDR input/output connectors, one to each sampler/pulser channel in the IC. The SiGe3 IC's two sampler outputs are then sent to to two SMA jacks, the first outputting the sample taken on the rising edge of the sampler clock, and the second containing the sample taken on the falling edge of the sampler clock. The sampler clock input, which must be a square wave, may be set to any frequency from 5MHz to 1GHz, causing the board take two pairs of samples (one on each clock edge) at rates from 5 million to 1 billion per second. A pulser clock input, which may be set to any frequency from 5MHz to 2GHz, and MUST be a square wave (preferably differential) with rise time under 100pS, causes the board to produce concurrent pulses on both of the SiGe3's I/O pins, which produce near-concurrent pulses at the two 2.4mm sampler/pulser TDR input/output connectors.
-
Product
Frequency generator
F170
-
The new F170 square wave frequency generator is based on the same hardware as the F165. It has all the features of the F165 plus 3 additional internal channels for a total of 6 programmable channels. It can run standalone up to 1500 program files copied from a PC or Mac or created from the keypad
-
Product
Audio Function Generator
-
Audio function generator app for the iPad, iPhone and iPod Touch. You can have up to five generators, each operating at a different frequency. Each generator can be one of the following types: Sine Wave, Triangle Wave, Sawtooth Wave, Square Wave, White Noise, Pink Noise
-
Product
Waveform Generators
-
UNI-T waveform generators adopt Direct Digital Synthesizer (DDS) technology to generate high frequency signals such as sine waves, square waves, harmonic waves, arbitrary waves, noise etc. Our signal generators also provide analog and digital modulation functions. All models have arbitrary waveform generator with editable software to generate complex waveform. UNI-T has a range of solutions from 5M to 600M to meet your performance needs, including UTG900E series mini generators for hobbyist and UTG9000T high-performance series. With industry leading pricing the UNI-T portfolio of waveform generators provides unparalleled customer value.
-
Product
Positive Displacement (PD) Meters
-
Positive Displacement (PD) flow meters are volumetric flow measurement instruments ideal for low flow rates, highly viscous fluids, and measurement of flows involving starts and stops or pulsing. Positive displacement flow meters are similar in design to the gear pump. The principle of operation is reversed however; instead of the gears driving the fluid, the fluid drives the gears. A non-intrusive hall-effect sensor detects the movement of the gear and as each gear tooth passes the sensor, a square wave pulse is produced and a discrete volume of liquid is measured. The resulting pulse train is proportional to the actual flow rate and provides a highly accurate representation of the fluid flow.
-
Product
Utilities
-
Audio signal generator that include sine waves, square waves, white noise, and pink noise. The noise signals may be octave-band limited. In landscape mode, you can set sweep start and stop frequencies, and a time in seconds.
-
Product
TMR Gear Tooth Encoders
-
MultiDimension Technology Co.,Ltd.
Geartooth Encoders of MultiDimension Technology (MDT) are non-contact incremental encoders for rotary speed and position measurement. Based on MDT’s unique Tunneling Magnetoresistance (TMR) sensor technology, they provide orthogonal differential square wave signals with high quality, along with an index signal and their inverse signals. The GE-T series are designed for 0.3~1.0-module gears with different teeth numbers. (Gear is the optional product).
-
Product
Loss Tangent M in Dielectric Oil
TAND220A
-
The measuring instrument type TAND220A complies with the international standard IEC 61620. The instrument is based on the so-called "low-amplitude, low-frequency alternating current square wave method" and allows accurate measurements of conductivity and relative permittivity. Conductivity measurement in the range of 0.01 pS/m to 20,000 pS/m allows the use of this instrument for quality control of high resistivity liquids even at room temperature. The TAND220A works with a low test voltage and also with a low test current so that it does not represent a danger for the operators.
-
Product
Handheld Digital Multimeter, 4.5 digit, up to 800 hours battery life
U1282A
Digital Multimeter
60,000 counts resolution on dual display0.025% basic DC voltage accuracy Longer battery life up to 800 hours Certified to IP 67 for dust and water protection Tested to withstand a 3-meter (10-ft) drop Programmable via USB (Download Programming Guide here)CAT III 1000 V/ CAT IV 600 V overvoltage protection Vsense for non-contact voltage detection Square wave output for generating pulse width modulation (PWM) signal Frequency counter Low pass filter
-
Product
Light-to-Frequency
-
Light-to-Frequency (LTF) sensors convert measurements of light intensity to a digital form for direct interfacing to a microcontroller. The output of the device is a square wave or pulse stream the frequency of which is linearly proportional to the light intensity. LTF converters are designed for applications such as ambient light measurement, light absorption/reflection in products such as white goods, photographic equipment, colorimetry, chemical analyzers and display contrast controls. They may be used in any system that requires a wide dynamic range, and/or high resolution digital measurement of light intensity.
-
Product
SINE (Sinusoidal) Targets & Arrays
-
Sinusoidal Target Arrays have been recognized as a superior test method for a variety of applications, from moiré contouring to reliable MTF Evaluation of materials, lenses, cameras, and electro-optical systems (Follow the hyperlink to learn about using Sinusoids for MTF eval). Sinusoidal Pattern Arrays are manufactured on two different materials for both reflective and transmissive applications. Because of the inherent limitations of reflective materials, the maximum spatial frequency of the reflective pattern arrays is limited to 20 cycles per mm, while the transmission film arrays are offered in various sizes up to 256 cycles per mm. In addition, the sinusoidal arrays are available in a Single Frequency Grating or with Multi-Frequency Gratings. If instead of continuous sinusoidal frequency, you are looking for a square wave frequency design, then look to the Ronchi Gratings page. Should you need to alter the size of the pattern or the substrate, fill out our Custom Test Targets and Charts form and start the conversation.
-
Product
CPCI Or PXI PCM & ARINC 717 Board
MS 1703
-
*Bus Interface - PXI / CPCI Bus*Microprocessor and FPGA design based Board*One Channel ARINC 717 Transmitter and Receiver*Generates all PCM telemetry signals like NRZ, Bi-Phase, Differential Bi-phase, DM signals*Used to test all types of PCM based telemetry equipments*Configurable output signals format (parity, word length, Minor, Major frame, Bit position)*User can configure the words and there positions in the frame*The word can be either a square / triangle wave data or constant data*1 MB Shared Memory for Data Storage*Driver interface for Windows2000/XP/VISTA and LINUX OS
