Debugging
fixes identified bugs.
See Also: Debuggers, In-Circuit Debuggers, Code Debuggers, JTAG Debuggers, Source Debugers
-
Product
68 Pin Breakout Interface
VSI-Breakout-68
-
The VSI-Breakout-68 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
Product
Multipurpose Debug Board
DB40-HPC Debug Module
-
The DB40-HPC Debug Card is designed for debugging of COM-HPC modules with FFC (FlexFoil Cable) debug connector. It includes an 80 port for Power on and Self-test (POST) via I2C interface, interface to SPI Flash for BIOS update, interface to EC for Embedded Controller (EC) update, Power and Reset buttons, and Status LEDs and Test Point for various debug tests.
-
Product
Evaluation boards
-
iSYSTEM evaluation and development systems are optimized for evaluation of the featuring microcontroller whether it fits the project requirements or for the development of the target application while the hardware is still in the design stage. Our systems are distinguished by high speed debug and trace connection to experience the full microcontroller capabilities.
-
Product
Lauterbach ΜTrace For Cortex M
-
A new all-in-one debug and trace solution has been developed by Lauterbach in response to the breakthrough of Cortex-M processors into the embedded market. This lower cost system called µTrace specifically targets the Cortex-M family.
-
Product
JTAG Probe
MAJIC
-
MAJIC (Multi-Architecture JTAG Interface Controllers) JTAG Probes are small, stand-alone, processor-based systems that provide an intelligent connection between host-based development tools (the debugger) and an embedded processor via its standardized JTAG debug logic IP macrocell.
-
Product
VME Test Extender 3U/220mm J2
111EXT3122-12XX
-
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
Product
Microwave Switches
SMX-7XXX (Microwave)
Microwave Switch Module
The AMETEK VTI Instruments SMX-7000 Series of microwave switch cards extends functionality typically reserved for dedicated stand-alone systems into the PXIe from-factor. Single and dual slot configurations provide the ability to mix and match multiple switch configurations including SPDT, SP4T, SP6T and Transfer. Embedded virtual schematic control further simplifies setup and debugging allowing all relays to be engaged independent of application software and device drivers. Ideally suited for medium-to-high density automated test equipment (ATE), the SMX-7000 Series deliver uncompromised measurement integrity ideal for the most demanding aerospace, defense and communication applications.
-
Product
Microelectronics Test & Engineering Services
-
EAG's Microelectronics Test and Engineering lab network provides semiconductor and electronics design firms worldwide with test, debug, and early engineering support to help you with new product introduction. We actively service a broad range of semiconductor and electronics companies worldwide. Services include ATE testing, Reliability testing and qualification, ESD testing, Failure Analysis, FIB Circuit Edit and Debug. for both ICs and systems
-
Product
50 Pin Breakout Interface
VSI-Breakout-50
-
The VSI-Breakout-50 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
Product
Wireless In-Circuit Test Fixtures
-
Higher density more complex circuit boards complicate testing requirements while smaller more tightly spaced test pads create a wiring challenge for the fixture fabricators, test engineers and maintenance personnel. Wireless fixtures solve the challenges associated with the nest of wires found in standard long wire fixtures. Wireless fixtures replace the “nest” of wires with copper traces on a multilayered printed circuit board called a Translator Board or T-Board®. Circuit Check’s wireless fixture technologies reduce test program debug and maintenance times while easing the ECO process. Thus allowing for the higher level of test performance, the ability to probe smaller denser targets and achieve ultra-high node counts.
-
Product
Test Research
TRI
-
REBOUNDER test kits feature two separate "Co-Active Seals", "Quick Twist" Locking Guide Pins, and boards constructed of fine weave G10/FR4, increasing testing reliability and accuracy while simplifying finishing, debugging, and maintenance. All H+W products are backed-up with our "Test-Assured" one year warranty, in writing, and SAME DAY SHIPMENTS
-
Product
RC BGA Interposer, LPDDR4 200-ball, Rigid, Connects Using 2x U4207A
W6602A
Interposer
The W6602A LPDDR4 rigid RC BGA interposer for LPDDR4 200-ball DRAM enables capture of simultaneous read and write traffic at data rates and has been tested to 3200 MT/s. Two U4207A zero Ω, 34-channel, soft touch pro, single-ended, 4 x 160-pin direct connect probes are required to connect the W6602A LPDDR4 BGA interposer into two U4164A logic analyzer modules. The W6602A LPDDR4 rigid RC BGA interposer allows signal access to the LPDDR4 signals critical to your debug and validation effort through a U4164A logic analyzer system. The probe works in existing designs and eliminates the need for up-front planning or redesign. The probe connects directly to the balls of the DRAM using a LPDDR4 200-ball riser (included) or an optional 3rd party socket (not provided), enabling operation and acquisition of LPDDR4 signals.
-
Product
Oscilloscopes
-
Berkeley Nucleonics Corporation
Is a type of electronic test instrument that graphically displays varying voltages of one or more signals as a function of time. Their main purpose is capturing information on electrical signals for debugging, analysis, or characterization.
-
Product
Bluetooth Stack Analysis Tools
Bluetooth Explorer 400
-
The Ellisys Bluetooth Explorer is a Bluetooth stack analysis tool for traffic monitoring, stacks and drivers debugging, interoperability verification and performance analysis.
-
Product
cRIO-9046, 1.30 GHz Dual-Core CPU, 2 GB DRAM, 4 GB Storage, -40 °C to 70 °C, Kintex-7 70T FPGA, 8-Slot CompactRIO Controller
786370-01
Embedded Controller
1.30 GHz Dual-Core CPU, 2 GB DRAM, 4 GB Storage, -40 °C to 70 °C, Kintex-7 70T FPGA, 8-Slot CompactRIO Controller - The cRIO-9046 is a rugged, high-performance, customizable embedded controller that offers Intel Atom dual-core processing, NI-DAQmx support, and an SD card slot for data-logging, embedded monitoring, and control. It includes a Kintex-7 70T FPGA with LabVIEW FPGA Module support for advanced control and coprocessing. The controller provides precise, synchronized timing and deterministic communications using Time Sensitive Networking (TSN), which is ideal for highly distributed measurements. This controller offers several connectivity ports, including Gigabit Ethernet, USB 3.1, USB 2.0, RS232, and RS485 ports. You can use the USB 3.1 ports to add a local human machine interface and program, deploy, and debug software, which simplifies application development.
-
Product
ESPI Analysis Application
TP601010
-
First released by Intel in June 2013, the Enhanced Serial Peripheral Interface (“eSPI”) is designed as a replacement for the Low Pin Count (“LPC”) bus. eSPI supports communication between Embedded Controller (EC), Baseboard Management Controller (BMC), Super-I/O (SIO) and Port-80 debug cards. eSPI was available in the Sky Lake chipset (2015) and is available in the Kaby Lake [current] chipset. Cannonlake will support eSPI and is slated for release the second half of 2017. Icelake is scheduled for release in 2019 and it will mark the first chipset when eSPI becomes mandatory.
-
Product
Netlist Analyzer
GateVision
-
GateVision PRO is the third generation of graphical netlist analyzers from Concept Engineering. Completely rewritten to run on modern 32/64bit platforms, GateVision PRO provides the designer of even the largest chips with intuitive design navigation, schematic viewing, logic cone extraction and interactive logic cone viewing for debug support and design documentation.
-
Product
Fifo Serial Analyzer for DOS
FLL
-
FLL is a DOS based protocol analyzer for debugging serial asynchronous communication. FLL uses the standard COM1 and COM2 ports of a PC and does not require any other hardware except for the physical connection to the line.
-
Product
HDO4000A High Definition Oscilloscopes
HDO4000A Series
Oscilloscope
HDO4000A oscilloscopes have 4 analog input channels, 12-bit resolution using Teledyne LeCroy’s HD4096 high definition technology, up to 1 GHz of bandwidth and a compact form factor with a large 12.1” multi-touch display. They are ideal for debug and troubleshooting of power electronics designs, digital power management or power integrity analysis, automotive electronics systems, and deeply embedded or mechatronic designs.
-
Product
DVB / MPEG Stream Analyzer program
dvbsnoop
-
dvbsnoop is a DVB / MPEG stream analyzer program, which enables you to watch (live) stream information in human readable form. Its purpose is to debug, dump or view digital stream information (e.g. digital television broadcasts) send via satellite, cable or terrestrial. Streams can be SI, PES or TS. Basically you can describe dvbsnoop as a "swiss army knife" analyzing program for DVB, MHP, DSM-CC or MPEG
-
Product
High-Speed Multi-IO SPI Host Adapter
BusPro-S™
-
The BusPro-S High-Speed Multi-IO SPI Host is designed with speed, versatility, and value in mind. Featuring a 60 MHz clock rate with up to 200 Mb/s throughput and support for standard, dual, quad, and 3-wire modes, the BusPro-S is the right tool for all SPI debugging applications-present and beyond.
-
Product
Protocol Analyzer and Exerciser
-
Keysight's protocol test solutions for each technology typically consists of both protocol analyzer application as well as a stimulus solution, such as an exerciser or traffic generator. Keysight's protocol test solutions combine multi-protocol analysis, traffic generation, performance and conformance verification to debug, validate and optimize your designs using high speed protocol standards.
-
Product
Fifo Serial Analyzer
FSA32
-
FSA32 is a Windows based protocol analyzer for debugging serial asynchronous communication. FSA32 uses the standard COM ports of a PC and does not require any other hardware except for the physical connection to the line.
-
Product
Oscilloscope
2563-MSO
-
The 2560 Digital Storage and Mixed Signal Oscilloscope (MSO) Series delivers advanced features and debug capabilities for a wide range of applications. With up to 300 MHz bandwidth in a 4-channel configuration, each model offers a maximum sample rate of 2 GSa/s, and a maximum memory depth of 140 Mpts. In addition, these oscilloscopes provide an 8” color display with 256 levels of color grading combined with a high waveform update rate up to 140,000 wfms/s, which allows the instruments to capture infrequent glitches with excellent signal fidelity.
-
Product
The all-in-one data logger for the entire vehicle networking
PM-200
-
The PM-200 sets the bar considerably higher on the topic of safeguarding and troubleshooting vehicles. Bus systems such as CAN, CAN-FD, FlexRay™, LIN, MOST150 and Automotive Ethernet are logged at a data speed up of to 120 MB/s. SSD removable media allow for quick evaluation and distribution of the data. Various upgrade options enable configuration for any application. Flexibility, programmability and support from debugging protocols make it possible to meet the high demands of functionality and fleet tests as well as of test runs.
-
Product
PCIe 4.0 Protocol Analyzer
Summit T48
Protocol Analyzer
Teledyne LeCroy’s Summit™ T48 joins the Summit™ T416 as the second protocol analyzer to be released in its family of tools supporting the PCIe 4.0 architecture. The new Summit™ T48 protocol analyzer based on the PCIe 4.0 specification supports up to 16GT/s and up to x8 lane width for protocol analysis. Companies that are interested in testing PCIe 4.0 based I/O cards such as Storage Controllers, Ethernet, Fibre Channel, Infiniband, and others will now be able to get all of the protocol analyzer debugging features they need, while being able to better manage their costs. SSD storage applications will also benefit from the integrated support for SSD bus protocols such as PCIe/ NVMe/ SMBus/ NVMe-MI/ TCG and others. When combined with Teledyne LeCroy’s Summit™ Z416 protocol exerciser, the Summit™ T48 will provide a deeper understanding of test results on a variety of test configurations. Teledyne LeCroy’s wide range of high speed interposers and probes provide full flexibility and connectivity to CEM and other form factor sockets on system boards as well as solder down and mid-bus probes.
-
Product
Intelligent CPCI Quad Industry Pack Carrier
CPCI-6713-4 IP
-
The board consists of private SDRAM and Flash memory attached to the 300 MHz TMS320C6713B DSP. An FPGA provides the timing and control. Peripherals include a serial port and connectors for IP mezzanine boards. Flash memory is availablefor downloading programs into a non-volatile memory. A PCIbus connector provides the interface to the host computer. A serial port is available for debugging.
-
Product
cRIO-9047, 1.60 GHz Quad-Core CPU, 4 GB Storage, -40 °C to 70 °C, Kintex-7 70T FPGA, 8-Slot CompactRIO Controller
785621-01
Embedded Controller
1.60 GHz Quad-Core CPU, 4 GB Storage, -40 °C to 70 °C, Kintex-7 70T FPGA, 8-Slot CompactRIO Controller - The cRIO-9047 is a rugged, high-performance, customizable embedded controller that offers Intel Atom quad-core processing, NI-DAQmx support, and an SD card slot for data-logging, embedded monitoring, and control. It includes a Kintex-7 70T FPGA with LabVIEW FPGA Module support for advanced control and coprocessing. The controller provides precise, synchronized timing and deterministic communications using Time Sensitive Networking (TSN), which is ideal for highly distributed measurements. This controller offers several connectivity ports, including Gigabit Ethernet, USB 3.1, USB 2.0, RS232, and RS485 ports. You can use the USB 3.1 ports to add a local human machine interface and program, deploy, and debug software, which simplifies application development.
-
Product
ATE Test & Engineering Services
-
We can provide a limited scope project or a full turn key solution where we analyze a data sheet and provide a full test plan. Our wide range of ATE test equipment and experienced team can support first silicon debug to release to high volume production for a wide range of products, from Digital to RF, including wafer sort and packaged part testing. Test platforms include Verigy, Teradyne, Advantest.
-
Product
PCI Express Gen 3 Test Backplane
SKU-015-01-PCIe
-
PCI Express Backplane was designed to support a variety of modern PCI Express board’s production testing and debugging. The backplane expands the Host computer into four x16 PCI Express slots via 10 ft. CAT7 data and 10-pin flat Power control cables. PCI Express Backplane and UUTs (unit under test – add-in PCI Express board) are powered by a standard ATX power supply connected to the backplane via 24 and 8 pin power connectors located on the backplane.
