Distributed Systems
-
Product
VLSI Test System
3380P
-
The 3380D/3380P/3380 test system have 4 wires HD VI source and any-pins-to-any-site high parallel test (multi-sites test) functions (512 I/O pins to test 512 ICs in parallel) that can meet the upcoming higher IC testing demands.
-
Product
Laser Diode Reliability Burn-In / Life-Test System
58602
-
Chroma 58602 is a high density, precision multi source measurement Unit (SMU) module with temperature control and exchangeable interface developed for burn-in, reliability and life test of optoelectronic components including laser diodes, VCSELs, VCSEL Arrays, silicon Photonics, photo-diodes and other similar components.
-
Product
In-Line RF Test Station
AP770
-
ICT, Functional, Hipot, Vision, ISP and RF test with low cost fixtures in a very compact test station footprint Works with PCBs up to 450×550 mm or with palletized devices Space for up to 25 VPC mass interconnect modules or YAV switching units
-
Product
Test System Optimized for High-Performance Digital and SoC
ULTRAWAVEMX44 and ULTRAWAVEMX20-D16
-
Teradyne is the leader in RF/wireless device testing and has a large installed base of UltraFLEX test systems with the UltraWave24 RF instrument. As new devices for handset and base station applications are introduced using mmWave technology, Teradyne’s mmWave instrumentation has expanded in anticipation of new testing demands.
-
Product
SoC Test System
T2000
-
SoC devices require small-lot high-mix manufacturing methods in the present era of rapid generation change. Semiconductor makers struggle with requirements to replace their testers on a 2-3 year cycle. The T2000 addresses their needs by enabling rapid response to market needs with minimum capital investment.
-
Product
Standard Test Systems
WaveCore™ Products
-
Textron Systems’ WaveCore family offers a variety of standard test systems with a primary application of satellite payload lab testing. Our systems can be deployed affordably for both production and engineering applications, providing industry-leading levels of data correlation with high system mean time between failures and low mean time to repair.
-
Product
VME Data Acquistion System
ADM-31
-
The VME-based ADM31 data acquistion system supports up to 48 differential or up to 96 single-ended analog inputs. The ADM31 control card is an intelligent A/D subsystem master or slave device that controls the analog A/D cards. Up to two A/D cards can be configured with the control card to complete the A/D system.
-
Product
Bloomy Simulation Reference System
-
The Bloomy Simulation Reference System provides a hardware in-the-loop (HIL) test environment for dynamic, closed-loop testing of many aerospace and transportation control systems. The reference system integrates the computing, I/O, and software components needed for standalone use or to form the basis of a more complex test system.
-
Product
Clock And Trigger Synchronization System
CLKSYNC-50
-
CLKSYNC-50 is a clock and trigger distribution system that provides multiple, independent copies of clock and trigger signals for multi-channel, Giga-sample ADC and DAC boards. Up to sixteen independent ADC or DAC clocks and triggers are synchronized.
-
Product
IFC Antennas & Radome Systems
-
System solutions providing inflight internet and live TV connectivity including satellite communications (SATCOM) systems, protective radome enclosures, antenna mounts, bird strike solutions, and adapter plates.
-
Product
In-Line 2-Module In-Circuit Test System; i337x, Series 5i
E9988E
-
Short wire fixturing eliminates problems commonly found with long wire fixturing, such as noise and deterioration of test stability. This translates into transportable, repeatable and stable tests on your i3070 Series 5i, even if you need to deploy tests halfway across the globe, or on different manufacturing sites.
-
Product
Photonics Module Test System
58625
-
Chroma 58625 provides characterization testing for 3D sensing illumination devices. various test modules are combined for validation testing under precise temperature control.
-
Product
Alpha Particle Counting System
UltraLo-1800
-
The UltraLo-1800 is a best-in-class alpha particle counting system. Our patented design reduces background rates by 50x compared to conventional systems.
-
Product
Multipurpose Mobile PXI DAQ System
-
The mobile DAQ system achieves seamless integration among signal conditioning, data acquisition, and synchronization that benchtop instruments would not have achieved. By choosing this system over using benchtop instruments, United Technologies Research Center saved hundreds of thousands of dollars.
-
Product
Checkpoint Security System
ConneCT
-
The ConneCTTM Checkpoint Security System is an advanced aviation security explosive detection system (EDS) engineered to deliver superior threat detection, dramatically improved passenger throughput, and low total cost of ownership.
-
Product
Physical Layer Test System
N19301B
-
The N19301B Physical Layer Test System (PLTS) 2022 software is a powerful signal integrity tool for today’s high-speed digital designers.
-
Product
Data Processing System
CRS-D8I-3VF1
-
The CRS-D8I-3VF1 VPX system’s I/O flexibility is capable of meeting a large number of configurations. It is designed to support Abaco Systems’ Intel 3rd generation Core i7 3U SBCs, Gigabit Ethernet switch, video compression card, CUDA-based graphics cards and a MIL-STD-1553/ARINC429 multi-protocol card.
-
Product
PXIe System Sync Module, 2 Port
M9032A
-
The M9032A has a Soft Front Panel (SFP) that provides a graphical user interface to the system sync module. It allows the user to set up the most commonly used functionalities of the module. The SFP also gives you the ability to check the module's connection status, configure the reference clock and IO settings, and perform firmware udpates.
-
Product
Mezzanine System
3560
-
ECM P/N 3560 provides four independent I2C channels. For ease of development a PCA9564 interface IC converts parallel data to I2C serial communication. Additionally an LTC1694 I2C accelerator IC decreases the rise time of the passively pulled up I2C bus allowing for greater capacitive loading or higher bus speeds. Each channel is comprised of SCL, SDA and two Grounds.
-
Product
VLSI Test Systems
-
50/100 MHz clock rate50/100 Mbps data rate1024 I/O pins (Max :1280 I/O pins)Up to 1024 sites Parallel testing32/64 M pattern memoryVarious VI sourceFlexible HW-architecture (Interchangeable I/O, VI, ADDA,)Real parallel trim/match functionTime & frequency measurement unit (TFMU)High-speed time measurement unit (HSTMU)AD/DA test optionSCAN test option (max 1G M/chain)ALPG test option for embedded memorySTDF tools supportTest program/pattern converter(J750, D10, V50, E320, SC312, V7, TRI-6020, ITS9K)User friendly windows 7 environmentCRAFT C/C++ programming languageSW (Software) same as 3380P & 3360P
-
Product
In-Circuit Test System
TestStation LX
-
TestStation LX is a cost-effective in-circuit test solution providing high-volume electronics manufacturers with reliable, high-quality test for the latest printed circuit board assembly technologies.
-
Product
Mini LED Backlight Module Automatic Optical Test System
7661-K003
-
Chroma 7661-K003 Mini LED Backlight Module Automatic Optical Test System contains a 71803-2 2D color analyzer to measure chromaticity and brightness
-
Product
Universal Function Test System for Industrial Electronics
-
General functional test system based on LXI instrumentation for high mix / low to medium volume manufacturing. DUTs are tested which are mainly used as communication and measurement modules in power plant technology, grid management and electrical drives.The system has a Virginia Panel adapter interface to which various desk adapters can be docked, including automated contacting of the DUTs. A camera for the verification of light emitting diodes on the test object is integrated in the adapter interface.
-
Product
SoC Test System
V93000 SoC / Smart Scale
-
Advantest’s V93000 Smart Scale generation incorporates innovative per-pin testing capabilities. Each pin runs it own sequencer program for maximum flexibility and performance, for example in multisite applications. Full test processor control ensures time synchronization between all card types, like digital, Power, RF, mixed signal and so on. The user benefits are reduced test time, best repeatability and simplified program creation. The system design makes it easy to extend your configuration with new modules and instrumentation, as your test needs change.
-
Product
Mezzanine System
5033
-
ECM P/N 5033 provides eight channels of RS485 / RS422 I/O. The 110 ohm termination for each channel is enabled or disabled in software. Disabling termination saves power by eliminating unneeded or redundant termination. Speeds of up to 20 Mega bits per second are possible, but this design also features a 250K bits per second slower edge rate mode. The 250K bit mode is valuable when EMI is more of a concern and throughput is not important. All channels power up as inputs with the outputs disabled.
-
Product
Image Sensor Test System
IP750
-
Teradyne's IP750 series dominates the image sensor tester market with its superior performance and low cost of test. The IP750 delivers high throughput and high parallel test efficiency, broad device test coverage from CCD and CIS, analog and digital capture, and concurrent image sensor and logic testing. In addition, Teradyne's IG-XL software environment provides easy, shorter test program development and easy maintenance.
-
Product
Mezzanine System
5181
-
ECM P/N 5181 uses TI TLV320AIC23 high resolution audio codecs to provide two channels of Audio input and two channels of Audio output. Each input channel consists of two inputs a left and a right, and each output channel consists of two outputs left and right. The outputs are muteable.
-
Product
Inflight Entertainment System Hardware
-
Innovative IFEC solutions that enable connectivity, entertainment, and control.
-
Product
Battery Management (BMS) Environmental Test System
-
The BMS Environmental Test System is a configurable platform simulating the essential signals used by Battery Management Systems (BMS) and cell-monitoring modules with the ability to perform environmental testing on multiple BMS units simultaneously. The system implements single-point value testing to evaluate specific BMS functions such as cell over and under voltage scenarios, cell leakage current, lost communications, or faulty system IO.
-
Product
Modular Breakout System 37-Pin D-type Plugin Module for 40-293
95-293-001
-
The 95-293-001 Plugin Breakout Module is designed to be fitted to a PXI 40-293 Programmable Resistor Module as part of the Pickering MBoS. The Modular Breakout System is designed to Simplify HILS (Hardware In the Loop Simulation) Applications.
