Walk-in Chambers
-
Product
Walk in chamber for Complex Salt Spray Test (Temperature controllable)
-
Guangdong Bell Experiment Equipment Co.,Ltd
Walk in chamber for Complex Salt Spray Test Relevant standards requirement1. Test Object: battery pack andsystem.2. Refer GB/T4 part 5.5.2 test method, test according to GT/T2423.17 test conditions.3. The salt solution was made up with sodium chloride (chemically pure and analytically pure) and distilled or deionized water，Its concentration is (5 + 1)% (mass fraction).4. (35 ± 2) ℃, the measured pH value is between 6.5-7.2.5. Placed the test objects in the salt spray chamber for cycling test. Each cycling duration for 24h. Spray salt solution to the test object for 8 hours under the temperature of (35± 2) ℃ , remain for 16 hours. Between the forth and the fifth hour in one cycles should be according to test requirement in GB/T 28046.1-2011, test mode with 3.2.6. Total 6 cycles testing.7. Salt spray test is not necessary for the test objects being installed in passenger, luggage or cargo compartments.
-
Product
Compact Humidity Chambers
FW1.5
-
The Bemco FW1.5, mechanically cooled Compact Humidity Chamber, has a temperature range of -28 C to +177 C (-20 F to 350 F) or -73 C to +177 C (-100 F to 350 F) and a humidity range of up to 5% RH to 95% RH. This chamber features direct dry air injection and a direct humidity sensor.
-
Product
Temperature Chambers Environmental Test Chambers
-
Proven Traditional Designs, evolved with New Generation FeaturesCyro Chambers come with 1 year Guarantee
-
Product
Table Top Temperature Chamber
-
Enables controlled test runs by manipulating the temperature conditions of an enclosed space.
-
Product
Altitude Simulation Test Chamber
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's Altitude Simulation Test Chamber
-
Product
Salt Spray and Fog chamber
P700
-
Bemco's Standard P700 Salt Spray and Fog chamber is designed to fill the needs of laboratories that require accurately controlled salt spray and fog tests on small components and assemblies. This unit meets all standard military, commercial, and ASTM salt fog corrosion and humidity corrosion tests.
-
Product
Environmental Chamber
REXMED REC-280
-
MOD. REC-280, AC 230/380/415V, 1/3 phase, Environmental chamber, HS CODE: 841989, UNCCS CODE: 484384, UMDNS CODE: 16327, Main construction: SS304, Interior: SS304, Exterior: SS304 powder coated, Insulation: Rigid polyurethane foam and glass wool, Controller: Fix point PID controller, temperature ˚C/PV and ˚C/SV, humidity %/PV and %/SV display and setting, Temperature range: -20˚C~100˚C, Humidity range: 20%RH~98%RH, Constancy: ±0.3˚C ±2.5%RH, Uniformity: ±1˚C ±3%RH, Temperature and humidity sensor: PT 100Ω, Temperature and humidity audio and visual warning and OFFS correction setting, Temperature heater: 2.3KW X 2pcs, Humidity heater: 4.5KW X 1pc, Heat up transition time: -20˚C~100˚C within 35 min, Refrigeration system: Air cooled, single stage, Cooling compressor: Bristol hermetic compressor, Cooling capacity: 3,140 Watts, 10,700 BTU/hr, 2,702 Kcal/hr, Cool down transition time: 20˚C~-20˚C within 45 min, Safety devices: No fuse breaker, refrigerator over load relay, refrigeration high pressure switch, over temperature protector, protection relay, protection fuse, water level control and overheat protector, Chamber: L100 X W80 X H100cm, Capacity: 800L, chamber with key lock, with lamp (DC 12V 50W) X 1pcs and double glass viewing window, testing cable port with cover: Ø25mm, 4 castors, W/S: shelf X 2pcs, standard testing wet cloth X 5pcs, PCV water container X 1pc
-
Product
Car in Cold Temperature Shock Chamber
-
Dongguan City Simplewell Technology Co. Ltd.
Car in Cold Temperature Shock Chamber by Simplewell
-
Product
IPX56 Simulation Rain Test Chamber
CX-IPX56A
-
Shenzhen Chuangxin Instruments Co., Ltd.
IPX56 Simulation Rain Test Chamber widely used in the lamps and electrical and electronic product certification testing institutions and for testing the waterproof of electrical and electronic products of shell protection level.
-
Product
Vehicle Salt Spray Test Chamber
-
Dongguan City Simplewell Technology Co. Ltd.
Vehicle Salt Spray Test Chamber by Simplewell
-
Product
Salt Spray Corrosion Test Chamber
-
Xi'an LIB Environmental Simulation Industry
Used to simulate harsh, corrosive environments by exposing materials to salt fog.
-
Product
IEC60529 IPX6X Sand Resistance Sand And Dust Chamber
CX-SC800PL
-
Shenzhen Chuangxin Instruments Co., Ltd.
IPX6X Sand Resistance Sand and Dust Chamber is applied to all mechanic, electric, electronic, electric chemical and mechanical and electric equipments, it is used to evaluate whether equipment can resistivity and storage, running or not in air of dry sand or dust. It is applied to IEC-529, GB4208-93, GB2423.37-89 and GJB150.12.
-
Product
Yellowing Resistance Chamber
-
Sataton Instruments Technology CO., Ltd
Yellowing resistance chamber also called as discoloration meter is the professional testing instrument for measurement of yellow resistance performance by simulating sunlight. It is a useful tool for testing the yellowing resistance property of light color materials or products such as white thermoplastic polyurethane elastomer shoe sole or light synthetic materials. The chamber can also be used for printing and packaging industry for deploying chemical dyes.
-
Product
USD Sand & Dust Chambers
USD-Series
-
USD-Series Sand & Dust chambers provide an environment to test the exposure of automotive and electronic components to concentrated levels of dust in order to validate product seal integrity.
-
Product
Mixed Gas Corrosion Test Chamber
-
Guangdong Test EQ Equipment co., Ltd.
- Precision Gas Dosing: Delivers exact concentrations of corrosive gases (e.g., H₂S, SO₂, Cl₂ with N₂ carrier gas; NO₂ with synthetic air) for repeatable test conditions. Supports simultaneous dosing of up to four gases, enabling multi-pollutant interaction studies.- Acrylic (PMMA) viewing window allows real-time monitoring of specimens without compromising test integrity.- Pressure monitoring system and gas sampling port ensure operator safety and compliance with industrial hygiene standards.- Advanced Environmental Control: Integrated air exchange module maintains consistent gas distribution and replicates dynamic atmospheric conditions.- Standard Compliance: Certified for IEC 60068-2-60, 60068-2-42/43, ISO 21207, and other global protocols, guaranteeing internationally recognized results.
-
Product
Thermal Shock Chambers
-
Shanghai Morningtest Environmental Chambers Co.,Ltd.
Thermal Shock Chambers are designed for the safe, efficient, and accurate environmental testing of electronics and consumer products, and aerospace, telecommunications, and military and defense components.
-
Product
Rotary Thermal Shock Chambers
TS Series
-
A Bemco exclusive product, the TS Series of Turboshock Rotary Thermal Shock Chambers feature an electrically driven, 180 degree reversing, rotating wall located between two chambers, one hot and one cold. Two loads can be handled simultaneously. Front loading and rear access doors allow full entry to each zone.
-
Product
Temperature Humidity Environmental Test Chamber
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell’s Temperature and Humidity Test Chamber is able to simulate a wide range of temperature and humidity environment condition for testing various products and components. It is widely used for basic thermal cycling test and accelerated stress test. We provide 6 standard models, test cabinet from 80L to 1000L, customized size is also available.
-
Product
Process Sense™ NDIR End Point Detector For Chamber Clean
-
The Process Sense endpoint sensor is a small, low-cost SiF4 sensor specifically designed for Remote Plasma Chamber Clean Endpoint detection for silicon-based CVD deposition chambers. Process Sense is based on infrared absorption, the only technique applicable to all plasma cleaning processes (in-situ and remote). It gets mounted onto a bypass on the rough line, ensuring no effect on deposition hardware. The signal level reported by the Process Sense, which is proportional to SiF4 concentration, can be used to determine the completion of the chamber clean process.
-
Product
Compact Temperature Chamber
FB1.5V-UHC Series
-
Based on the proven Bemco FB1.5V Compact Temperature Chamber, the FB1.5V-UHC offers spectacular temperature change rates in excess of 75 C per minute. With an extremely compact footprint these chambers cost about 1/3 of the amount of a typical 2-zone thermal shock chamber such as a Bemco FS2V.
-
Product
Environmental Test Chambers / Rooms
-
Is an enclosure used to test the effects of specified environmental conditions on biological items, industrial products, materials, and electronic devices and components.
-
Product
EMC Test Chamber
-
Imagine being able to test whatever you want, whenever you want. No more delays or travelling to external parties. Owning an in-house test chamber lets you control every aspect of testing while meeting all relevant EMC test standards and criteria.Fast. Reliable. Worry-free.
-
Product
Walk-In/Drive-In Temperature Environmental Chamber
-
Burnsco Environmental Test Chambers
These custom designed chambers are used for testing large products, vehicles, or batch testing. They offer temperature and humidity simulation capabilities for climatic testing and temperature/humidity cycling whenever there is a need to simulate wide temperature and humidity extremes. They can be made almost any length, width or height.
-
Product
IEC60529 IPX3/4 Oscillating Tube Spray Water Test Chamber
-
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60529 IPX3/4 oscillating tube spray water test chamberWorkshop:60*60*60 cm / 100*100*100 cm
-
Product
Stability Test Chambers
-
It provides outstanding stability testing performance for manufacturers of pharmaceuticals, cosmetics, food, and personal care products.
-
Product
High and Low Temperature & Low Pressure Chamber
LAP-100
-
It is according to GB10590 / GB15091 low temperature / low pressure test chamber requirements; GB11159 low pressure test chamber requirements; GB / T2423. 25-1992 low temperature / low pressure integrated chamber requirement; GB / T2423. 26-1992 High temperature / low pressure integrated chamber requirement; GJB150. 2-86 low temperature / low pressure test etc standards. It’s used to test the In aviation, aerospace, information, electronics and other fields, to determine the instrumentation, Electrical products, materials, components, equipment etc.
-
Product
Rain Test Chamber - Twin Shower
-
The Drive-In Rain Test Chamber is generally used to conduct whole body testing of assembled vehicles under different rain test procedures to study and estimate their structural degradations and destructions induced by rain/water. The twin shower area with 1.1 million litre & 0.35 million litre volume is enclosed in a shed where arrays of pipes are interconnected to form zones to ensure the uniform spraying as per JSS 55555 test standard. The water gushes through the nozzle at a flow rate of up to 288 cu m/hr and the test chamber water collection system have a central grating with sufficient slope to collect the sprayed water during operation and circulate it back to the water reservoir to ensure close loop circulation.
-
Product
Temperature Chambers For Thermal Tests
-
Before anything reaches out for market distribution, you would need to determine its exact quality and performance to that follows to the point with readings. Thermal and environment testing are some of the most positive aspects to get your materials tested for their underlying performance capacity and reliability in quality.
-
Product
Reach-In Humidity Test Chamber
-
The Humidity Test Chambers from Weiber are corrosion test chambers that are used to simulate high or low humidity conditions for testing the rust preventing capacity of various oils and greases. These high low humidity simulation chambers find wide spread usage in research organizations, educational institutions and industrial units and are most commonly employed by petroleum and chemical industries.
-
Product
Thermal Shock Chamber
-
Sanwood Environmental Chambers Co ., Ltd.
Three zone thermal shock chamber uses the test material structure or composite material to withstand the degree of extreme high temperature and low temperature in a continuous environment in an instant, so as to test the chemical changes or physical damage caused by thermal expansion and contraction in the shortest time.
