Synchro / Resolver Converters
converts Synchro and Resolver analog shaft angle signal to a digital signal.
See Also: Synchro/Resolvers
-
Product
Balanced O/E Converter
TIA-527
-
The TIA-527 balanced optical to electrical converter provides adjustable gain and a bandwidth of DC to 125 MHz. It is useful for coherent heterodyne detection applications, spectroscopy and similar applications for which the ability to discern small variations in signal strength in two optical paths is critical..
-
Product
POWER Converter AC
NMTP
-
The NMTP AC power converters with two mutually independent analogous outputs serve to convert single-phase or three-phase AC power into current or voltage analog signals. The A output is used for active power measurements, the B output for reactive power measurements.
-
-
Product
USB Converter Cables
-
These converter cables connect various serial interfaces to a computer USB port.
-
Product
DC/DC Converter 50 W
CTS-60-6843
-
DC/DC converter with 50 W from Premium | input ranges 43.2 - 90 VDC | output 5 V | operates in temperatures from -25 - +85 °C | designed according to EN50155
-
Product
Interface & Level Converters
-
Advanced Science and Novel Technology, Co., Inc.
2-channel LVDS-to-CMOS converter (Receiver) and 2-channel CMOS-to-LVDS converter (Transmitter)Optional signal splitter function with selectable inversionOptional DS (Data/Strobe) encoding/decoding for compatibility with Space Wire StandardProgrammable LVDS/CML/ECL Receiver input interfaceTrue LVDS Transmitter output interfaceFlexible selection of enabling and operational modes of the channelsHigh-impedance states of disabled CMOS outputsSingle +3.3V power supplyIndustrial temperature range
-
Product
BCD to Binary Converter
BCD250
-
Computer Conversions Corporation
The BCD Series of BCD to Binary Converters will convert 4 digits of scaled BCD angle data with a full scale of 359.9degrees into 12 Bits of binary angle data (MSB=180degrees). These units are entirely digital, require no timing or control signals and do this conversion in less than 500 nano-seconds. Logic levels are TTL/DTL compatable and +5V DC power is required. They are packaged in a 2.6 x 3.1 x .82" H PC board mounting module.
-
Product
Compact Converters
-
Virginia Diodes offers compact converters (CCs) for frequency up and down-conversion. These converters are easy to use and well suited for high performance up and down conversion of wide band modulated millimeter-wave signals. VDI CCs offer full waveguide band coverage and are available from WR28 (22.5-40 GHz) to WR2.2 (330-500 GHz) with additional CCs under development. Compact converters can typically be delivered within 9-11 weeks ARO or less. Contact VDI for more information.
-
-
Product
ITSM Synchro
-
The Impulsive Test Synchronization Module (ITSM) is a device aimed at generating a digital synchronization signal, to use the PDBaseII system for impulsive voltage PD test. The digital synchronization signal generated by the ITSM, is synchronized with the voltage impulse of the impulsive source (voltage generator). The ITSM must be connected between the DIN channel of PDBaseII and the output of the synchronization sensor (e.g. capacitive coupler). The ITSM provides also a low voltage signal reproducing the impulsive voltage source.
-
Product
Audio A/D Converters
-
Analog Devices offers audio analog-to-digital converters (ADCs) for applications such as automotive, home theater, consumer audio, and PCs. These ADCs offer cost effective solutions and easy interfacing to ADI's SHARC® processor, Blackfin® processor, and SigmaDSP™ products.
-
Product
Synchro/Resolver to Digital Converters
-
Resolvers and synchros are transducers that convert the angular position and/or velocity of a rotating shaft to an electrical signal. Both deliver signals proportional to the sine and/or cosine of the shaft angle. A resolver-to-digital or synchro-to-digital converter converts these signals to a digital output corresponding to the shaft angle and/or velocity. ADI’s family of RDCs and SDCs offer solutions for these applications.
-
-
Product
Low Power DC/DC Converters
-
The 4:1 Input Voltage 75 Watt WDE includes remote sensing, ultra-wide output voltage trim, and remote ON/ OFF. The digital power management enables increased reliability, configurability, voltage / current precision and fault management.
-
Product
Resolver-to-Digital Converter
MSX-RDC-17
-
The resolver-to-digital converter MSX-RDC-17 is a device for supplying and acquiring a resolver. It converts the position value given by the resolver into a digital incremental output signal. The resolution of the incremental encoder output can be defined using the switch on the front side of the MSX-RDC-17.
-
-
Product
Sources & Converters
-
High reliability, low-phase-noise, high-coherence, large operational temperature range, exceptionally low g-sensitivity for high vibration and shock performance.
-
Product
DC/DC Converter 150 W
CQB150W-110S15
-
DC/DC converter with 150 W from Cincon | input ranges 43 - 160 VDC | output 15 V | operates in temperature from -40 to +105 °C | according to EN45545-2 fire and smoke
-
Product
Digital to Analog Converter
-
20-bit digital-to-analog (D/A) converter offering 20-bit monotonic performance over the specified temperature range. It utilizes delta-sigma technology to achieve inherently linear performance in a small package at very low power. The resolution of the device can be programmed to 20 bits for Full-Scale, settling to 0.003% within 15ms typical, or 16 bits for Full-Scale, settling to 0.012% within 2ms max. The output range is two times the external reference voltage. On-chip calibration circuitry dramatically reduces low offset and gain errors.
-
-
Product
Protocol Converters
-
Applied Systems Engineering, Inc
ASE provides a total solution approach to the area of protocol test equipment with its’ family of PC based protocol test products. The ASE2000 RTU Test Set is a full-featured protocol test unit that provides the user with a powerful and flexible tool for testing and maintaining SCADA RTU and SCADA IED equipment and diagnosing communication problems.
-
Product
Analog to Digital Converter
7418/7419
-
Supports thermocouples, RTD's, strain gauges, voltage in, 4-20 mA, thermistors, and resistorsUp to 16 differential input channels plus sensor excitationEach channel is software programmable for sensor type, gain, low-pass filtering, scan rateAuto-calibration eliminates trimpotsLow power consumption
-
Product
Media Converter, 1000Mbps, SFP
EKI-2741F
-
Provides 1 x 1000 Mbps Ethernet port with RJ45 connectorProvides 1 x 1000 Mbps fiber port with SC or SFP (mini-GBIC) type connector for 1000Base-SX/LX deviceProvides DIP switch for full/half duplex settingSupports MDI/MDI-X auto crossoverSupports Auto-NegotiationSupports redundant 12 ~ 48 VDC power inputProvides flexible mounting: DIN-rail and Wall mountProvides Link Fault Pass-through (LFP)Jumbo Frame: 9K bytes
-
Product
Current/Voltage/Frequency Converter
SCMA-VADC-710
-
The SCMA-VADC-710 current/voltage/frequency converter is switched between SensoControl measuring devices and hydraulic installations in order to capture the switching status of these components
-
Product
O/E Converter
TIA-3000
-
The TIA-3000 is an instrument for the laboratory or for field use. This amplified optical-electrical converter can be used with a wide range of oscilloscopes and digitisers to provide the utility of a convenient, easy to use fibre optic probe. Energising the unit, the optical signal presented to it is faithfully reproduced on the CRT of the oscilloscope or digitiser.
-
Product
Radar Scan Converter PMC
Eagle
-
Curtiss-Wright Defense Solutions
Eagle is a flexible and powerful radar scan converter that is based upon field-proven technology and comes in a compact and mechanically ruggedized PMC form factor. Eagle features a low power, rugged design, enabling it to operate in a wide range of environments, including conditions of high temperature and vibration.
-
Product
Unmanaged Media Converters
-
Advantech's unmanaged Ethernet to fiber media converters feature compact industrial-grade, flexible design, fitting any industrial environment.
-
Product
LVDT to Digital-RVDT to Digital Converters
ITA
Computer Conversions Corporation
LVDT Displacement transducers accurately measure position and displacement. The strength of the LVDT is in its principle of operation. As LVDT sensors are inductive, there is no electrical connection across the sensor, which ensures clean, accurate data and a long life.
-
Product
Synchro Simulator
SPA-CASE
Simulator
Computer Conversions Corporation
The Synchro Simulator has two modes of operation: Static and Dynamic. The mode of operation is selected by the position of the mode switch. In the static mode, the thumbwheel switches select the output angle. In the dynamic mode, the speed and direction switches determine the rate and direction of synchro outputs. Self test circuitry continuously monitors and displays the output.
-
Product
Frequency Converters & Transceivers
-
Mercury Systems’ converter and transceiver products are at the forefront of SWaP-optimized RF integrated products. Through substantial R&D investment and a library of building blocks, Mercury Systems has the capability to rapidly execute on the most complicated of custom transceiver designs. As the OpenVPX industry leader, Mercury Systems knows how to make integration into your system a breeze.
