Bare Board
is a printed wire board only.
See Also: Bare Board Probes, Bare Board Testers, Bare board Fixtures
-
Product
3.4 MP Autofocus Low Light USB Camera Board With Liquid Lens
See3CAM_30
-
See3CAM_30 is a 3.4MP UVC Compliant, low light, autofocus USB camera with liquid lens. It is a two-board solution with AR0330 CMOS image sensor from ON Semiconductor and USB 3.1 Gen1 type C interface board. See3CAM_30 is a colour camera with S-mount lens holder and does not require any special camera drivers to be installed in the host PC. See3CAM_30 is customizable and it is a Ready-to-Manufacture camera with all the necessary firmware built in and compatible with the USB Video Class (UVC). It consumes less power and doesn't heat up. There is no mechanical movement like in VCM motor for autofocus. Hence the life of the lens increases.
-
Product
16-bit, 200KHz, 16 Isolated Differential Analog Input Board, 8 Isolated 24V Digital I/O
APCI-3002
-
Analog input board, 16-bit resolution, 16 differential inputs with 200 kHz sampling rate.
-
Product
General Purpose 4 Channel Optocoupler Board
-
A general purpose 4 channel optocoupler board using H11G2 optocouplers (see above schematic). Resistors, capacitors, and connections to terminal strip are made by customer to allow for complete flexibility
-
Product
Fiber Optic Transmitter/Receiver & Repeater Board
-
To be used with 1000 micron plastic fiber optic cable. Fiber distance should be limited to 40 meters unless special low-loss fiber is used. These units can be used as repeaters to go greater distances.
-
Product
PXI Express Board Virtex-5 DAC Module1GHz, 14-bit DAC
SMT781
-
Sundance Multiprocessor Technology Ltd.
The SMT700 module uses a Xilinx Virtex 5 LXT or S XT to implement the interfaces the board provides. The FPGA can be configured either via the onboard flash, or through the Xilinx JTAG header.
-
Product
PCIe I/O & Comm Board
79G5
Multifunction I/O
NAI's latest generation single-slot, half-size PCIe board, the 79G5 can be configured with up to three NAI intelligent I/O and communication function modules. Ideally suited for high channel density and combined multifunction I/O requirement systems, the 79G5 delivers off-the-shelf solutions that accelerate deployment of digital and analog I/O, position control and measurement/simulation and communication interface applications.
-
Product
Interface Board for 100 BaseT Ethernet
40-965-911
Interface
The 40-965-911 is a converter card for the 40-201 Ethernet/AFDX Fault Insertion Switch. Adapts the 78-Pin D-type connector on the front of the module to 8 RJ45 sockets and one 9-way D-type connector for fault signals. Allows the fault insertion testing of 100 BaseT Ethernet signals.
-
Product
12-bit, 100KHz, 8SE/4DIFF Isolated Analog Input Board
APCI-3001-8
-
8 single-ended or 4 differential inputs 12-bit resolution Optical isolation 500 V 100 kHz data transfer rate Automatic analog acquisition 8 digital I/O, 24 V, isolated, timer Trigger functions Graphical display of the measured data
-
Product
Desktop Meter Qualification Board
2199
-
Providing complete capabilities for evaluating meters and communications performance, TESCO’s Desktop Meter Qualification Board (Catalog No. 2199) can generate any voltage and load conditions the meter may encounter in the field. Apply non-sinusoidal voltages with complex load waveforms. Perform disconnect tests and reconnect tests without having to worry about being able to drive the meter’s switches.
-
Product
Conduction Cooled VPX Interface Board with PCI Express Host Interface
EXC-8000ccVPX
-
The EXC-8000ccVPX is part of the 8000 family of multiprotocol carrier boards. This conduction cooled VPX interface board has a PCI Express host interface and can support up to four independent removable modules and 10 on-board Discrete channels. Each removable module can be any of the 8000 family modules.The EXC-8000ccVPX supports Direct Memory Access (DMA), which enables the board to access system memory for reading and writing independently of the computer’s CPU. This results in faster data transfer to and from the board, with much less CPU overhead than when not using DMA.The EXC-8000ccVPX is supplied with C drivers, including source code. Mating connector provided for I/O connection.
-
Product
CPCI ARM LPC3250 Board
MS 1513
-
- 32 Bit ARM LPC3250 Processor (256KB SRAM)- 133MHz External Bus Speed and 266 MHz internal CPU Speed- 32 Bit, 33MHz CPCI Bus, 6U Form Factor- External memory ( Flash – 2 MB, RAM - 512 KB, DPRAM – 128KB)- 10/100 MBPS Ethernet Interface- USB 2.0 Host/Device Interface- 2 RS232 Serial Ports, 4 RS422 Serial Ports- M Module Interface- 6U board compatible with CPCI & PXI backplanes- High Speed Logic Device- Hot Swap Feature- Front Panel and Rear IO Interface- External Bus through Rear IO- Reception of 3Kbytes within 2ms through Ethernet- Board Dimension is 160mm x 233.35mm- Power Requirements: +3.3V, +5V and +/-12V- Board Dimension is 160mm x 233.35mm- Board has Rear IO interface- Ethernet, JTAG, RS232, USB connectors at front side- BSPs and Driver software for Windows and Linux OS
-
Product
General Purpose 4 Channel Optocoupler Board
-
A general purpose 4 channel optocoupler board using H11G2 optocouplers (see above schematic). Resistors, capacitors, and connections to terminal strip are made by customer to allow for complete flexibility.
-
Product
DSP Based Serial Communication Board
CPCI-ISC8
Communications Module
The CPCI-ISC8 is an intelligent DSP based serial communication board. This 3U board is based on the CPCIIPC product and has been modified to remove the IPinterface and to support additional I/O features. The CPCIISC8 provides mechanical support and the electrical interfaces for an I/O mezzanine board. Multiple CPCI-ISC8 boards may be installed in a single system.
-
Product
VXI C-Size Blank Board
115250
-
* C-Size blank PC Board for mounting devices, modules or circuits.* Includes VXIbus P1 and P2 connectors and decoupled power pads.* Includes pads for all VXI bus signals.* Includes pad patterns for common front panel connectors, LEDs, and a Reset Switch.* Includes CAD Design aids for Schematic Capture, PC board layout and front panel machining.* Use with ICS 1, 2 and 3-slot wide Module Shield Kits to create a complete enclosed module.* Use with ICS Front Panel Kits to add a front panel and ejectors to the blank board.
-
Product
Multi-Protocol Board
EXC-8000cPCI
-
The board supports up to 6 modules, and each module represents an independent test and simulation device. Most modules are based on existing Excalibur products such as the 1553 Px family and the ARINC429 RxTx.
-
Product
Quad IF Board
DP-VME-1242
-
DP-VME-1242 is VME64x, 6U single-slot solution for high sampling rate and down conversion applications. Applications include - IF signal processing, radar systems, communication systems, and GPS systems.
-
Product
Digital I/O Board w/CoS IRQ
104-DIO-48S
-
*48 or 24 parallel lines of 82C55 digital I/O with tristate buffers prevent unintended control of external equipment*IRQ on input change of state (COS) eliminates the need for constant polling*High sink/source current 64mA/32mA*I/O pulled up to 5V for contact monitoring*Compatible with Opto-22 and other industry standard I/O racks
-
Product
SMT & THRU HOLE LOADED BOARD TEST PROBES
SERIES 43
-
MechanicalMINIMUM CENTERS: .075 (1.91)FULL TRAVEL: .250 (6.35)WORKING TRAVEL: .167 (4.24)OPERATING LIFE: 1,000,000 cyclesElectricalMAXIMUM CURRENT: 3 amps continuous at working travel, non-inductiveRESISTANCE: At 35 mA test current,30 mOHMS meanMaterials and FinishesPLUNGER: Heat treated beryllium copper or steel hardened to 55-60RC, both 24Kt gold plated over nickelBARREL: Nickel silver with 24Kt gold plated ID and OD over nickelSPRING: Music wire, 24Kt gold plated over nickel
-
Product
Express Multi Protocol Board
EXC-8000PCI
-
The EXC-8000PCIe is a PCI Express card supporting up to eight independent 8000 family avionics communication modules, allowing multiple different protocols to be mixed and matched on a single card. Modules available include MIL-STD-1553, MIL-STD-1760, MMSI, ARINC-429, ARINC-708, ARINC-717, Serial, Discrete and CAN bus.The EXC-8000PCIe supports extensive error injection and detection capabilities, IRIG B Time Code input, and can be ordered with an extended operating temperature range of -40ºC to +85ºC and conformal coating. The EXC-8000PCIe is supplied with C drivers, including source code.
-
Product
Analog Input Expansion Board
MSXB 037
-
The Microstar Laboratories Analog Input Expansion Board, part number MSXB 037, provides analog input expansion for Analog Backplane systems. The Analog Input Expansion Board is compatible with the MSXB 030-01 and MSXB 031-01 Analog Backplanes.
-
Product
Digital Termination Boards
MSTB 008
-
For quick and secure connection of discrete wires to a Data Acquisition Processor (DAP) board, use the MSTB 008 Digital Termination Board.
-
Product
3U OpenVPX™ Rugged, Cybersecure & Anti-Tamper Single Board Computer
68ARM2
Single Board Computer
The 68ARM2 is a 3U OpenVPX Zynq® UltraScale+™ Quad-core ARM® Cortex™-A53 MPCore™ based Single Board Computer that can be configured with up to three NAI Smart I/O and communications function modules. Ideally suited for rugged Mil-Aero applications, the 68ARM2 delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems in air, land and sea applications.
-
Product
RFSoC Board
VP431
-
VP431, the next generation of our highly successful VP430, is a 3U VPX commercial off-the-shelf direct RF processing system that features the 3rd-generation Xilinx Radio Frequency System-On-Chip (RFSoC). The VP431 maximizes I/O channel density, reduces the radio frequency signal chain complexity, and allows for heterogeneous processing capability.
-
Product
3U CPCI Multifunction I/O Board
75G5
Multifunction I/O
NAI's latest generation 3U cPCI Multifunction I/O and Communication Board, the 75G5, can be configured with up to three smart function modules. Ideally suited for rugged military, industrial, and commercial applications, this low-power/high-performance board delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems.
-
Product
Nano-ITX Embedded Board
-
The Nano-ITX form factor is designed as a high integrated native x86 embedded platform, measuring a mere 120 mm x 120 mm which measures in at 50% smaller than the Mini-ITX form factor. The Nano-ITX form factor is available with a rich feature set and is targeted at the fast-emerging embedded markets, allowing developers to highly customize their system designs in the low-profile and fully-configured embedded devices.
-
Product
Starter Boards
-
Clicker, Clicker 2, Clicker 4, FLip & Click, Universal Boards, MINI, Ready, mikroBoard, StartUSB, & more
-
Product
Squid Carrier Board™ Family PCI Express Gen 3 Carrier Board for One M.2 PCIe SSD Module
SKU-086-31
-
The Squid PCI Express Carrier board for M.2 SSD module is the smallest carrier board on the market. PCI Express Carrier board was designed to expand modern motherboards that have PCI Express interface. It allows vertical installation in any 1U servers or appliances.
-
Product
Analog Interface Boards
Model 4861B OEM
-
* 114578-24 board has 4 isolated analog outputs, 4 isolated analog inputs, 4 isolated drivers and 8 digital inputs* GPIB interface header includes GPIB address switch input signals.* Serial interface header includes RS-232 and RS-485 signals. Use the 114597 Serial Cable Kit to connect the serial signals to your rear panel* Use with any ICS GPIB Connector/Address Switch Assembly.* Runs on 12 Vdc regulated power.
-
Product
DUT Prototype Board
DPB8800
-
The DPB8800 is an 11? x 14? PC board used to interface the tester with the Device Under Test (DUT). This board contains generous area for custom circuitry and extra relays. The DPB8800 is also available with standard solutions to test families of components like Op-Amps, Regulators, ADC?s and DAC?s. +/-15 V and +5 V are available to support circuitry biasing.
-
Product
TMR Switch Sensor Demo Board
-
MultiDimension Technology Co.,Ltd.
Demonstration kit for MDT omnipolar and bipolar TMR switch sensors
