Line
-
Product
100Hz-50kHz LCR Meter –
11021/11021-L
-
Chroma Systems Solutions, Inc.
The Chroma 11021/11021-L are the most cost-effective digital LCR Meters available, providing 100Hz, 120Hz, 1kHz, and 10kHz test frequencies for the 11021 and 1kHz, 10kHz, 40kHz, 50kHz test frequencies for the 11021-L. The standard RS232 interface, optional GPIB & Handler interfaces, high speed and stable measurement capabilities enable the Chroma 11021/11021-L for use in both component evaluation on the production line and fundamental impedance testing for bench-top applications.
-
Product
4 Port Phone Line Simulator (FXS) Adv
SIM-4FXS-A
-
This unit has 4 analog phone lines (FXS) making it a perfect tool for testing VoIP gateways, IVR, modems, access servers, audio conference equipment or anything that requires phone lines. Telephone line simulator acts like a "telephone company in a box" providing dial tone, ring voltage and all advanced phone line features such Caller ID, Call Waiting, Call Hold, Three Way Calling and many others.
-
Product
Modbus Transmitter for LPPHOT01 Probe
LPPHOT01S
-
The transmitter LPPHOT01S converts the mV analog signal generated by the illumination probe LPPHOT01 into a digital signal suitable to be transmitted over a serial line RS485 with MODBUS-RTU protocol.
-
Product
Pole Mounted Detector of PtG and PtP faults in 6-69V Line
LineTroll 111K
-
The unit mounts 3-5m below the conductors and monitors all three phases. The indicator is powered by replaceable long-life lithium batteries which have a lifeexpectancy of 10-15 years. It provides a 360 degree visibility for indication both for transient faults and permanent faults.
-
Product
Pulsation Testing Equipment
-
Parker's offering of pulsation testing equipment quantifies Square Root and Gauge Line Errors in natural gas orifice-flow measurement, identifying inaccuracies caused by compressor-induced pulsation and differential-pressure discrepancies
-
Product
Temperature and humidity outdoor, indoor probe
T3110
-
Programmable temperature and humidity transmitter is equipped with temperature and relative humidity sensors. Measured values are also converted to other humidity interpretation - dew point temperature, absolute humidity, specific humidity, mixing ratio or specific enthalpy. Degrees Celsius and Fahrenheit are user selectable. Transmitter contains a microprocessor based control circuitry in a durable plastic case with connection terminals and sensors in a filter with stainless steel mesh. Humidity transmitters is equipped with two galvanic isolated 4-20mA outputs. Configuration of outputs and output range are user adjustable. Large dual line LCD for simultaneous display of T+RH or other humidity interpretation is an advantage. Display is possible to switch off. Computerized design ensures temperature compensation of the humidity sensor and fail indication. State-of-the-art capacitive polymer sensor ensures excellent calibration long term stability, inertia against water and condensation. Transmitters are designed for use in non-aggressive environment.
-
Product
Digital Ior Leakage Current Clamp Tester
MCL-400IR+
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
・About Ior Leakage CurrentRecently, the leakage current clamp meter is widely used for insulation control of low voltage circuit as the supplementary method of the insulation resistance measurement. The control of leakage current has the advantages to enable the prediction of insulation condition in the electrical power line without having to shut off the power. The leakage current (Io) includes the capacitive leakage current (Ioc)originated in the capacitance and the resistive leakage current (Ior) originated in the insulation resistance each related to the ground. It is considered that the measurement of resistive leakage current (Ior) is the very useful and effective method for the insulation control of low voltage circuit. However, it was difficult to measure the resistive leakage current (Ior)with traditional leakage current clamp meter. MCL-400IR new digital clamp tester enabled the measurements of the resistive leakage current (Ior)without voltage input(phase detection).
-
Product
Digital Automated Fiber & Ferrule Interferometer For Multi-Fiber Connectors
DAFFI MT
-
Data-Pixel has developed a cost effective interferometer line for high volumes production without compromising accuracy or performance. Based on our extensive interferometer manufacturing experience we designed the DAFFI MT to be robust, fast and accurate in order to meet all manufacturing or laboratory environments.
-
Product
Magnetic Shielding Cabinet for EMI Testing
SDR-2000B
-
Cabinet Shell2mm galvanized cold-rolled steel sheetCabinet Door0.9*1.7m(L*W)0.6*0.6mCabinet Window0.3*0.3*0.025m(L*W*T) with 4mm holeN/APower Supply Filter30A/220V30A/220VInternet Line FilterRJ-45N/ACabinet Inside DecorationPVC ceiling, PVC plastic steel wall, 10mm wooden + 2mm galvanized steel sheet floorCabinet Inside Size2*1.2*1.8m0.8*0.8*0.8mAfter Packing Size2.2*2.3*2.3m1*1.1*1.2mAfter Packing Weight800kg200kgWorking With EMI-9KA/EMI-9KBEMI-9KA/EMI-9KB, PC, Testing load, and operator insideTesting load is inside to connect with EMI-9KA/EMI-9KB via BNC
-
Product
Thermalert Clinical Montoring Thermometer With Analog Output
TH-5/AOP
-
The TH-5?AOP is one of our most economical precision thermometers in the Physitemp product line. The TH-5/AOP offers the same high accuracy (0.1°C ±1 digit) and resolution as all our other thermometers, but with a narrow temperature range. The TH-5 is ideally suited for either a laboratory or hospital setting where continuous temperature readings within the physiological range are sufficient.
-
Product
Extractive Gas Analyzers
Advance Optima and EasyLine Series
-
ABB offers three series of extractive gas analyzers catering to a diverse range of industries and applications. Sensing technologies perfected over more than 90 years are the foundation for a modular architecture delivering market leading performance and reliability – Uras (NDIR), Limas (NDUV), Magnos (Paramagnetic), Caldos (TCD), Fidas (FID), ZO23 (Zirconia). ABB also offers tunable diode laser (TDL) analyzers that measure in situ, directly at the stack or process line. The analyzers are world renowned for ruggedness, easy installation and operation in safe and hazardous areas, simplified calibration and outstanding possibilities for integration in digital networks.
-
Product
Power Conversion Automated Test Platform
C8000
-
Chroma Systems Solutions, Inc.
Power conversion testing is our core competency. Chroma’s engineering delivers cost-effective automated test system and software platforms to fit your Design Validation Testing (DVT) requirements in the lab or High Speed Functional Testing in the production line. Built into each system are Chroma’s years of expertise, precision instrumentation, pre-written test libraries, and local program management with global support. From power conversion to battery to electrical safety, our test systems will maximize your time, improve your validation process, and increase your throughput.
-
Product
15T Standard Running Line Monitor
RLM15T-3.0-S
-
The DLM 15T Running Line Monitor measures the tension on a rope passing through its three wheels. Typically used in cable laying and winch operations to measure and record line tension the robust design has become an industry standard. The monitor can be supplied as a separate item for integration with customers existing PLC’s or with a DLM digital display/HMI touch screen display.
-
Product
In-Process Test OTDR
8000i
-
The 8000i In-Process Test OTDR is the most recent addition to Photon Kinetics' family of innovative solutions for optical fiber cable testing. The 8000i's "cable test optimization" provides the balance of OTDR dynamic range and dead zone performance that's proven to be most effective for accurate characterization of typical fiber cable lengths. Dynamic range has been maximized to reduce measurement time, while resolution has been tuned to ensure that typical cabled fiber defects are detected. The 8000i delivers this optimized measurement capability at a more economical price than our full featured, final QC 8000 OTDR, which makes it a perfect fit for "in-process" testing on ribbonizing or loose tube production lines.
-
Product
R.F. Coupler and high Pass Filter
7415-3
-
There are those who disagree with the r.f. conducted susceptibility test setup of Method CS02 of MIL-STD-462. Homemade rigs have sprouted to comply with the coupling capacitor requirement, each with it own disadvantage. Our little Type 7415-3 R.F. Coupler is the answer. A neat little box with BNC connectors and a pair of binding posts, it is rated at 270 V.A.C. at the LINE terminals and 20 volts PMS into the GEN port. Looks good and does a fine job.
-
Product
Power Induction Tester
MIG-ITU-K44
-
The MIG-ITU-K44 is designed for power induction testing at line frequencies of 50 and 60Hz. Power induction tests need only be performed at the frequencies of the public power supply or railway power of the country of application. Basic and enhanced level tests can be performed according to ITU-T K44.
-
Product
ASI Test Equipment
-
ASI has designed its own line of aviation electronics test equipment utilizing modern design and manufacturing techniques. Being primarily a service facility, ASI is able to identify what type of test equipment is required in the avionics field from a service technician's view. This equipment is designed with the technician in mind, for ease of operation and maintenance.
-
Product
Ultrasonic Level Transmitter
USonic
-
The Drexelbrook family of Ultrasonic technology level products offers an affordable two wire and line powered version for non-contact level measurement of liquids and slurries for level, distance, volume and open channel flow.Measurements of level, distance, volume and open channel flow is easily configured through the menu driven display. The Usonic level transmitter is offered with a two wire 4-20 mA, Hart output signal and is suitable for all Class I Div. 1, Zone 0, I.S. or XP locations. The bench configuration eliminates the need to move process material levels for calibration.
-
Product
Pipe & Cable Locators
-
Schonstedt Pipe & Cable Locators have been setting the standard for reliability and dependability in locating buried utilities – water pipes, sewer pipes, cable, electrical lines, and gas —quickly and easily.
-
Product
Durable, Ultra Small & Flexible Test Assembly
StormFlex® 034
-
Storm Flex® line of flexible cables, the 034 diameter cable offers the same superior mechanical benefits in a new miniature size.Its ruggedness and durability combined with its ultra-small size, very low weight, and extreme flexibility make Storm Flex® 034 cable assemblies the perfect fit for applications such as:- Test & Measurement ~ where flexibility and robustness minimize mating errors.- Systems ~ with complex installation or deployment that can compromise mechanical & RF stability.- Gimbal ~ with requirements for cables operating to 50 GHz.- Digital Test ~ needing minimized stress at the connector to connector interface.- High Density ~ utilizing multi-cable interconnects with centerline spacing as low as 0.07 inches.Storm Flex® 034 cable is also recommended as a semi-rigid replacement in applications where a sem-rigid cable is impractical to deploy and routing may result in assembly breakage or electrical failure.
-
Product
Controllers
-
All BK Mikro controllers utilize the latest technology for the most flexibility and programming options. The compact, din rail mounted control unit mounts easily in the electrical cabinet and provides a full line of advanced functions.
-
Product
cRIO-9053, 1.33 GHz Dual-Core CPU, 4 GB Storage, -20 °C to 55 °C, Artix 7 50T FPGA, 4-Slot CompactRIO Controller
786424-01
Embedded Controller
1.33 GHz Dual-Core CPU, 4 GB Storage, -20 °C to 55 °C, Artix 7 50T FPGA, 4-Slot CompactRIO Controller - The cRIO-9053 is a rugged, deployable controller for data acquisition and control applications. It offers Intel Atom dual-core processing, an Artix-7 FPGA, and four slots for C Series modules. It runs the NI Linux Real-Time operating system with access to the I/O through NI-DAQmx drivers or with the LabVIEW FPGA module. The controller provides precise, synchronized timing and deterministic communications over the network using TSN, ideal for distributed measurements and control. This controller offers one Gigabit Ethernet port, one USB 3.1 host port, one USB 2.0 device port, a trigger line, and a μSD card slot for storing data locally. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
Product
Unregulated Power Supply Models
AC-DC Single Output Unregulated Power Supplies
-
To meet the need for unregulated DC power at a low cost, Acopian offers a broad line of Plug-in power modules with output voltages to 950 volts.
-
Product
OEM Gas (NO) Analyzer
BE-220FSD
-
The BE-220FDS is an OEM NDIR detector for measuring NO in automotive emission gases. The BE-220FSD can output NO concentration by digital data and analog voltage. In addition, it can be connected with the HORIBA BE-150 bench by serial line and relay the commands for BE-150. The BE-220FSD meets OIML Class 0 and complies BAR-97 & GB18285-2018 specifications.
-
Product
Validation Testers
M Series
-
The M Series line introduces a new class of massively parallel SerDes validation testers that are ideal for high-volume data collection and characterization. Constructed using a collection of Introspect Technology’s D Series modules that are operated seamlessly using the Introspect ESP software, these massively parallel testers are able to interface to high-speed devices in their entirety.
-
Product
Trackside Equipment
-
The Automotive assembly track lineside environment requires numerous amounts of tooling & equipment to ensure build phases are completed productively. Jackmark Engineering provides a wide variety of custom designed trackside jigs & fixtures, test leads and assembly aids including validation tooling to various assembly departments from HVAC to end of line.
-
Product
High Voltage Mini-SIL / SIP Reed Relays
Series 131
-
The Pickering Series 131 is a new range of very small Single-In-Line reed relays intended for voltages very much higher than standard small SIL relays. The vacuumed, sputtered ruthenium reed switches have a superb low level performance also, which makes them an ideal choice where a wide range of signals are involved.
-
Product
X-Scan U
-
X-Scan U series based on the novel digital platform improves image quality, increases maximum scanning speed and saves the overall system cost of industrial in-line and off-line nondestructive testing (NDT) of tires. X-Scan U series is an enhanced product family of U-shaped X-ray line cameras developed and optimized specially for high-speed digital tire inspection utilizing panoramic X-ray sources.
-
Product
Programmable AC and DC Power Source
AFX Series
-
The AFX Series is a family of high power, single, split and three phase, AC, DC and AC+DC output capable Power Sources. Available models range from 6 kVA to 90 kVA with available configurations to 150kVA. Using a modern user interface for ease of use, the AFX Series is cost effective and fully programmable for both basic frequency conversion and advanced AC power line or DC power disturbance test applications.
-
Product
Acoustic Target Impact Localization System
ATILS
-
In peace time, for training purposes, artillery units conduct their frequent target practicing.Both the skills of the gunners and the forward observers need to be improved, their communication cycle to be shortened.Forward observing is a dangerous task during war time, causing a justification to find other ways to localize impacts and adjust fires.Furthermore, the sheer lack of a line of sight, because of topography and/or weather, also thrives the need for other solutions to determine the impact coordinates.
