Modules
See Also: Contacts, Boards, ITA, Cable Assembly, Cards
-
Product
cDAQ-9181, 1‑Slot, Ethernet CompactDAQ Chassis
781496-01
Chassis
1‑Slot, Ethernet CompactDAQ Chassis - The cDAQ‑9181 is a CompactDAQ Ethernet chassis designed for small, distributed sensor measurement systems. The chassis controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. You can use this chassis with a combination of C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The chassis also has four 32‑bit general‑purpose counters/timers. You can access these counters through an installed, hardware‑timed digital C Series module for applications that involve quadrature encoders, PWM, event counting, pulse train generation, and period or frequency measurement.
-
Product
NI-9234, 4-Channel, 51.2 kS/s/channel, ±5 V, C Series Sound and Vibration Input Module
779680-03
Sound and Vibration
4-Channel, 51.2 kS/s/channel, ±5 V, C Series Sound and Vibration Input Module - The NI‑9234 can measure signals from integrated electronic piezoelectric (IEPE) and non‑IEPE sensors such as accelerometers, tachometers, and proximity probes. The NI‑9234 is also compatible with smart TEDS sensors. The NI‑9234 delivers a wide dynamic range and incorporates software-selectable AC/DC coupling and IEPE signal conditioning. The input channels simultaneously measure signals. Each channel also has built-in anti-aliasing filters that automatically adjust to your sample rate. When used with NI software, this module provides processing functionality for condition monitoring such as frequency analysis and order tracking.
-
Product
PXI RTD Simulator Module, 16 Channel, PT100
40-263-201
Simulator
The 40-263-201 is a 16-channel PT100 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
Product
4/8-port Asynchronous Serial Communications Modules
cPCI-3534/3538-S
Communications Module
- 32-bit CompactPCI, PICMG 2.0 Rev 2.1- Plug-and-play, IRQ & I/O address automatically assigned by PCI BIOS- 4/8 asynchronized communications ports with intelligent buffer- Three RS-232 ports and one isolated RS-422/RS-485 port with 2500 VRMS isolation voltage for cPCI-3534, and eight RS-232 ports for cPCI-3538- Surge protector in TXD/RXD signal line
-
Product
PXI Dual 2x2 RF Matrix SMB 75 Ohm
40-837-002
Matrix Switch Module
The 40-837-002 is a 75Ω 2x2 RF matrix with 2 banks in a single PXI slot. Loop-thru connections are provided on both the X and Y axis allowing the attachment of terminations for unused signals or for expansion to other matrices. Larger matrices are easily built with varied X and Y dimensions, such as 8x2 and 4x4 using multiple 40-837 modules.
-
Product
Integration testing
-
Integration testing primarily focuses on verifying data communication among different modules of the software project. Integration tests determine the effectiveness and performance of different software modules when they are connected to each other.
-
Product
24 Channel Isolated Counter / Totalizer & 16 Channel Pulse Simulator
DP-cPCI-5004
-
DP-cPCI-5004, Isolated Pulse Simulator / Counter / Totalizer module is an integrated module for pulse output, pulse measurement and event counting. The module has 16 isolated channels of pulse output at desired frequency. The 16 channels are divided into three groups . The first two groups have four differential and one single ended channels each.
-
Product
NI-6584, 16 Mbit/s, 32-Channel Digital I/O Adapter Module for FlexRIO
781290-01
Digital I/O Adapter
16 Mbit/s, 16-Channel Digital I/O Adapter Module for FlexRIO—The NI-6584 is a digital I/O adapter module that, when combined with a PXI FPGA Module for FlexRIO or the Controller for FlexRIO, creates a digital instrument for interfacing with 16 RX and TX pairs of RS485 or RS422. This digital I/O adapter
-
Product
QuadPOD Conditioning Interface
JT 2147/VPC
-
The JT 2147/VPC is a variant of the JTAG Technologies QuadPOD signal conditioning interface specifically designed for use within Virginia Panel Corporation’s mass interconnect interface. The unit integrates both the JT 2148 transceiver circuitry, two independent, programmable TAP modules (of type JT 2149) and two TAP modules with I/O (of type JT 2149/MPV) on a single board that interfaces via the VPC QuadraPaddle connectors type G20x or G14x.
-
Product
Test FMC Mezzanine Module
TFMC900
-
The TFMC900 is an FMC (FPGA Mezzanine Card) Mezzanine Module designed to test ANSI/VITA 57.1 FMC Carriers during development or series production. Additionally, it offers the possibility to realise various I/O solutions for connected FMC Carriers. Interconnection of the High Pin Count FMC Connector signals can be verified by JTAG and by functional tests. A loop-back of the 10 multi-gigabit transceiver interfaces allows interconnection checks for the high-speed serial interfaces.
-
Product
High-Density 128-CH Isolated DIO/DI/DO PCI Cards
PCI-7442/7443/7444
Analog Input Module
Responding to the industry"s need for high-density digital input/output modules, the ADLINK PCI-7442/7443/7444 DIO card series delivers up to 128 opto-isolated channels for a wide range of demanding PCI-based applications. The PCI-7442/7443/7444 series comes with 64 (PCI-7442) or 128 (PCI-7443) opto-isolated digital inputs and 64 (PCI-7442) or 128 (PCI-7444) opto-isolated digital outputs. With a 1250 VRMS (excluding cables) channel-to-system isolation protection, these cards are shielded from damage caused by accidental contact with external voltage while promoting simple ground connections. All input channels are identical non-polarity with each line isolated and suited to collect digital inputs even at high-noise environments. Featuring a Change-of-State (COS) interrupt function, the PCI-7442/PCI-7443 instantly generates an interrupt request to the PCI controller when it detects a sharp change in the logical state of any of its digital inputs.
-
Product
PXI 5A Power Multiplexer, 1-Bank, 48-Channel, Independent Isolation
40-651A-101
Multiplexer Module
The 40-651A-101 is part of our range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC. It is available in the following 1-pole multiplexer formats.
-
Product
16-Bit, 4-Channel, 100 KS/s, Programmable TestScale Analog Output Module
788270-01
Analog Output Module
TS-15110 TestScale Analog Output Module (10V, 16 bit, 4ch)
-
Product
PXI/PXIe Power Relay Module, 18xSPST, 5 Amp, 50-pin SGMC Connector
40-153-004
Relay
The 40/42-153-004 is a PXI/PXIe high density power relay module with 18xSPST switches rated at 5A. User connection is via a 50-pin SGMC male connector. The 40/42-153 range is available in 18, 25, 36 or 50 SPST configurations with or without hardware interlock. Electro-mechanical power relays are used which are suitable for switching loads up to 5A at 250VAC.
-
Product
PXI Programmable Resistor Card 2-Channel 2.5 Ohm to 2.04k Ohm - SPST
40-294-122
Programmable Resistor Module
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
96 Pin 1.27mm Pitch Micro-D Cables - 96 Pin to Alternative Connector for Pickering Products
-
The connector to connector cable assemblies below are suitable to use with Pickering cards and modules that utilize a 96-pin micro-D connector.
-
Product
Processor Module
UPM STM32F429
-
The universal processor module UPM STM32F429 is intended for use as part of devices developed by the user and for providing control of these devices via various control interfaces and for ensuring the interaction of these devices with a PC via the Ethernet or USB 2.0 HS interface.
-
Product
Mini PCIe Expansion Kit
iDoor
-
Advantech’s iDoor Expansion Module is a brand-new design concept which utilizes the Mini PCIe format. iDoor modules include: communication, fieldbus protocol and digital I/O. The highly flexible customization and easy assembly provide integrated solutions to meet different needs.
-
Product
PXI 4 Slot BRIC Solid State 160x8 1-Pole (5 sub-cards)
40-563A-021-160X8
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance PXI matrix requirements and are constructed using solid-state switches. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
Dual 8-Channel 1-Pole 16 Amp PXI Power Multiplexer
40-662-002
Multiplexer Module
The 40-662 range of 16 Amp PXI power multiplexer modules is available in seven configurations ranging from 4-off 2:1multiplexers to 1-off 16:1 multiplexer. Power multiplexer modules are intended for switching heavy AC or DC loads or for the slave switching of large external relays, contactors and solenoids. All versions are suitable for switching loads up to 16 Amp at 250VAC. User connections are made via a 20-way GMCT plug which is fully support by our comprehensive range of cables and connector accessories.
-
Product
Engine Controller
FireLynx
-
The fully programmable FireLynx control module is used for Engine Development, Test and Control as well as directing the real time operation of Fuel Injector Test Stands.
-
Product
PXI/PXIe Microwave Relay, Single SPDT, 67GHz, 50Ω, SMA-1.85, Remote Mount
40-780B-571-E
Relay
The 40-780B-571-E (PXI) and 42-780B-571-E (PXIe) are single SPDT 67GHz unterminated microwave relay modules with remotely mounted relays. The 40/42-780B range is available with one, two, three or four SPDT panel mounted relays capable of switching frequencies up to 67GHz in 50Ω or 2.5GHz in 75Ω. Connections are made via high quality RF coaxial connectors, SMA or N-Type for 50Ω and 1.6/5.6 in 75Ω versions.
-
Product
Logic Analyzer Probe
FS2510AB
-
The FS2510AB is a logic analyzer probe used to test DDR4 DIMM memory. When used with the triggering and analysis capabilities of Keysight’s U4154A/B/64A logic analyzer modules, it gives the user an effective tool for debugging, testing and verifying DDR4 DIMMs.
-
Product
ITA, 9075, 75 Module, Triple Tier
410104258
ITA
The 75 Module, triple tier ITA is rugged and perfect for high I/O test and measurement applications. This ITA is made of steel to prevent any deflection caused by the high insertion forces from the available I/O. The added tapped holes on the back of the frame allow you to attach an enclosure or custom fixture.
-
Product
Digital I/O via Ethernet
2610
-
Connects to Ethernet via 2601 communication moduleAll channels may be independently programmed as input or outputEight channels have pulse width modulation outputsRJ-11 I/O connectors eliminate need for external terminal blocksSupport for interlocks and multiple power supplies per channelInput channels are debouncedWatchdog Timer
-
Product
Chassis, Carriers And Controllers
-
Automated measuring systems based on the open standards AXIe, VXI, LXI and PXIe have enclosures (base units or chassis) in which modules of a given standard are mounted. Informtest Holding manufactures a wide range of chassis in open standards AXIe, VXI, LXI and PXIe.
-
Product
1MP OV10633 Custom Lens Camera Module
e-CAM1M_CU10630_MOD
-
e-CAM1M_CU10630_MOD is a High Dynamic Range (HDR), Wide Dynamic Range (WDR), custom lens camera module targeted for surveillance and security applications. This HDR camera module based on the OV10633 sensor from OmniVision is e-con’s first Wide Dynamic Range (WDR) camera module that can stream 1280x720p video at 30fps over its 8-bit digital video parallel interface. This 1MP WDR/HDR camera module is compatible with almost all of the popular Application Processor families such as TI OMAP, TI Sitara, NXP/Freescale i.MX, Marvell Xscale, Samsung etc and also compatible with Digital Signal/Media Processors such as TI OMAP35x, TI DaVinci DM37x, DaVinci DM3xx etc. The camera module is mounted with an industry-standard S-mount M12P0.5 lens holder allowing our customers to choose a lens of their choice.
-
Product
Receiver, G12, 12 Module, Rack Mount
310104338
Receiver
Receiver, G12, 12 Module, Fixed Rack Mount Unit 15" Platform Supports 275 lbs
-
Product
PXI 2A Multiplexer, 1-Bank, 64-Channel, 2-Pole
40-614C-016
Multiplexer Module
This 1-bank, 64-channel, 2 pole version is part of the 40-614C High Density 2A multiplexer module range that is available in 20 configurations (see Also in this Range link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
8 Pin Power D-Type Female Connector, 40A, PCB Mount
40-963-008-RF
-
This connector is suitable for Pickering Interface's modules that use the 8-Pin Power D-Type connector. It is designed to allow users to make a termination via a PCB.
