Contacts
See Also: Modules, Wire, Connectors, Patchcords, Flying Leads
-
Product
80 Channel Relay Switch
DP-VXI-4503
-
DP-VXI-4503 is a 80 channel, one Form C (SPDT) relay switch designed as a C size VXI module. This high density switch module is designed with a register based interface occupying only one VXI slot. This module uses two Form ‘C’ relay switches. Out of the two contacts in each relay, one is used to provide the status of the relay through read back and the other is used for switching purpose.The user can write the command for the selected channels on to the primary latch of the FPGA section. Readback is available to confirm the selected commands. On command, the data from the primary latch is transferred to the secondary latch. The relay driver section provides the necessary drive to switch ON the relays. The buffers in this section drive the relay coils.This module features a back plane trigger for VXI triggered operation. On receipt of the back plane trigger the programmed relays will be energised/de-energised. Alternatively, software trigger can be used.
-
Product
Shoe Heat Resistance Tester
UI-FT28
-
Shoe Heat Resistance Tester is to test shoe outsole and upper hot contact resistance ability especially for safety shoe. Heat Resistance Test Method includes ISO 20344, SATRA TM49, EN 344 and etc.
-
Product
Plugbord
3797
-
VECTOR Electronics and Technology, Inc.
30 Gold plated edge contacts (15 each side)on 0.156"(3.96mm) centers.Convenient easy-to-read hole marking legend on both sides.No circuit pattern edge contacts only.
-
Product
Bolt Extensometers for Proof Load Testing
Model 3565
-
Jinan Testing Equipment IE Corporation
The Model 3565 uses hard conical points to contact the bolt at the center of the head and at the bottom. It is fully adjustable for different length bolts ranging from 25 mm (1 inch) in length to 150 mm (6 inches) standard. Extension beams are available for longer bolts. The standard maximum measuring range is 1.25 mm (0.05 inches). Generally, on longer bolts this extensometer will be self-supported without requiring any centering marks or punch marks on the bolt. For shorter bolts these marks may be required. If the conical pins are sharp, marks are often not needed even on the shortest bolts.The extensometer has a zero adjustment screw to adjust the length between the contact pins. This is used to set the output voltage to zero, which corresponds to the correct starting position for the test. It also includes a breakaway lower arm. In the event a bolt should fail, the breakaway arm snaps free, helping to prevent damage to the extensometer. This is easily re-installed. In the event that bolt failures are likely during a test, it is recommended the user attach a cord around the upper part of the beam and tie the other end to the test frame to prevent the extensometer from falling. The conical point contacts included with the extensometer are made from tungsten carbide.The Model 3565 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
Product
Pneumatic, Contact, Receiver (with valve), Hose Barb, for 1/8" [3.2 mm] ID Tubing
610131107
Pneumatic Contact
Primary mating contact 610131106.Used in receiver module p/n 510104185, mates to contact p/n 610131106 and ITA modulep/n 510108160.
-
Product
Micro Coax, Contact, ITA, RG316
610141101
Coax Contact
Primary mating contact 610140101. (May mate with other Receiver contacts, as well.)Mechanical SpecificationsDurability 10,000 cyclesContact Material Center Conductor – BeCuShield – BrassContact Plating 50µ" Au over 100µ" NiContact Termination Center Conductor - SolderShield - CrimpInsulator PTFEMating Force 1.5 lbs max [0.68 kg]Electrical SpecificationsCharacteristic Impedance 50ΩFrequency Range DC – 3 GHzVSWR 1.22 @ 3 GHzInsertion Loss – √f(GHz) x .06 dBDWV 800 V RMSContact Resistance 6 mOhms center/4 mOhms outer Cable Specifications RG316Environmental SpecificationsOperating Temperature -65°C to +125°CVibration MIL-STD 202, Method 204, Test Condition DShock MIL-STD 202, Method 213, Test Condition IInsulation Resistance 2000 MOhms Min.
-
Product
Signal, Contact, Receiver, QuadraPaddle, 5 Amp, Twin Female
610138200
Signal Contact (Receiver)
Primary mating contact 610138118. (May mate with other Male Adapter and ITA contacts, as well.)Specifications Operating Voltage & Current 5 Amps Max. Continuous; 600 volt Max. use of wire Mil-W-16878/4Contact Resistance 25 mOhms Max.Measured at 50 mV @ 100 mADielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 5000 MOhms Min.Contact Body BeCu/PhBrzContact Plating 30µ” Au over 100µ” NiCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAvg Mating Force(lbs) 0.24
-
Product
Signalling Relays
N.S1
-
N.S1 signalling and vital relays are a consistent, adaptable range of relays with plug-in connection, small size, modular construction, low power consumption, compliant to French and SNCF standards, conformity to UIC recommendation, Ag / Ag CdO contacts and 24 V standard.
-
Product
Plugbord
3682-2
-
VECTOR Electronics and Technology, Inc.
44 Gold plated edge contacts (22 each side)on 0.156"(3.96mm) centers.Interleaved buses pattern on wiring side only solder- coated for user convenience.Bus outline silkscreened on component side to facilitatecomponent placement. Mounts DIPs with 0.3”, 0.4” & 0.9” lead spacing. Unclad test point area at top of board Row and column legends provided
-
Product
I-V Measurement Systems
-
The I-V Curve Data Acquisition includes a fixture for holding cells for testing (see Figure 1 below). This fixture can accommodate cells from small to up to 100 mm x 100 mm. Adjustable cell stops, in the X & Y-axis, are provided to consistently locate the cells for testing. Two micro-manipulators are provided as shown in Figure 1. Each micro-manipulator has two spring loaded contacts to allow 4-wire measurement even for cells that have top contacts only. Two back-side voltage contacts are embedded in the Plate (galvanically isolated from the Plate) and make good electrical contact when the cell is held down by vacuum to the plate. All voltage and current probes are gold-plated. The cell is held down with vacuum during testing (built-in vacuum pump).
-
Product
Limit Switches
-
With its choice of casings, wide range of actuators, variety of connections and high degree of resistance to impact and splashes, Crouzet Switches offers limit switches available in the following ranges: Metal body, Plastic body, Special products and Products for severe environments. Their main characteristics are: IP6x seal, a wide range of actuators (plungers and rollers), rotary heads with momentary action, positive break contacts, compact size, etc. They also offer the option of having special levers, prewiring, connection via ISO cable glands, etc.
-
Product
Milliohm Meter
16502
-
Chroma Systems Solutions, Inc.
Basic accuracy : 0.05%Pulsed test current output mode is used to reduce thermal EMFs affection on milliohm measurementDC test current output mode is used to fasten measurement speed for inductive DUTDry-circuit test current output mode (limited Max. 20mV) is used to measure such contact resistances where the maximum open-circuit voltage must be limited to 50mVTemperature correction (TC function) regardless of material or temperatureUseful temperature conversion function for motor/ coil evaluation4 channels R scan with balance check function for fan motor (combined with A165017 option)0.001mΩ~1.9999MΩ wide measurement range with 4½ digits resolutionStandard RS-232 interfaceOptional GPIB & Handler interfaceBin-sorting functionComparator and pass/fail alarming beeper functionLarge LCD display (240 x 64 dot-matrix)Friendly user interface
-
Product
Vector Network Analyzer Extenders
-
Our Vector Network Analyzer Extenders (VNA Extenders) allow high performance frequency extension of vector network analyzers into the THz range. The available models cover a Frequency Range from 50 GHz up to 1.1 THz. Contact RPG to discuss VNA Extender configurations that will gain the best performance for your application.
-
Product
Pneumatic, Contact, Receiver, Ferruless Fitting, for 3/8" OD, 1/4" [9.5 x 6 mm] ID Tubing
610131101
Pneumatic Contact
Primary mating contact 610132101.Pneumatic Contacts are available with either ferruless polytube fittings (3/8" tubing OD) or hose barb (3/8" tubing ID). Ferrules fittings securely attach tubing without hose clamp - which is recommended for the hose barb type (hose clamp not included).
-
Product
Milliohm Meters & Microhm Meters
-
Shanghai Beha Electronics Co., Ltd.
Makes measurements by passing a constant current through the device under test (generally a conductor, contact or low resistance) and measuring the voltage across it. It has visual LED checks for excessive; potential lead resistance (RP) and current lead resistance (RC). Should the instrument become too warm, the temperature sensor will shut down the current (ISCOFF).
-
Product
Sola-Sure System
-
Health & Safety solution to support the industries where dangers may exist of UV lamp radiation coming into contact with human skin. Increasingly driven by national and government regulations the Sola-Sure identifies higher energy radiation that can cause damage to humans in solarium, medical treatment and the industrial UV work place.
-
Product
Compressed Air Monitor and Alarm
SENTRY
-
The Edgetech Instruments Model SENTRY detects upset conditions in compressed air systems by constantly monitoring dew point and pressure at the system header or dryer output. The SENTRY alarms when a loss in pressure or high dew point is detected. This information is valuable in detecting compressor failures, system leaks, or drops in dryer performance. A pulsing audible alarm and strobe lamp provide quick notification of upset conditions. The SENTRY also provides a local display of pressure, dew point and system status as well as 4-20mA analog output and alarm relay contacts.
-
Product
Digital Circuit Breaker Analyzer
CT-3500 S2
-
The CT-3500 S2 is Vanguard’s second generation, stand-alone, digital, microprocessor-controlled, circuit-breaker timer. It measures the elapsed time from the instant a breaker coil is energized to the instant of opening or closing of a circuit-breaker’s dry contacts. In addition to timing a breaker’s contact response time, the CT-3500 S2 can also time relays or other switching functions that use an initiating trigger voltage (24-300 Volts DC or AC). The timer-triggering voltage starts three independent electronic timers. Each timer is individually stopped by its respective dry-contact closing or opening. The CT-3500 can fully analyze the timing of all circuit breaker operations (Open, Close, Open – Close, and Close – Open). Timing results are displayed in milli-seconds and cycles on the unit’s back-lit LCD screen and can be printed on the built-in 2.5-inch wide thermal printer.
-
Product
Thermometers
-
At PCE you will find both a contact and non-contact thermometer for measuring and recording temperature. There is a thermometer to measure different temperature ranges between -200 and 1767ºC / -328 ... 3212ºF. Measurement of temperature is done in many different sectors. We also offer a thermometer that can indicate temperature in ºC, K (Kelvin) and ºF, as well as another that is water resistant.A wide range of thermal elements and type-K sensors are available for the thermometer. ISO calibration certificates, which include a laboratory calibration, can be ordered for most models in our thermometer range. Thermometers are instruments we use to measure the temperature of people or things.The most used and known thermometers are mercury thermometers used to measure peoples temperature and consisting of a graduated glass capillary and a pool of mercury in one end, but there are many types of thermometers such as digital thermometers that we have introduced which take temperature measurements on contact with an object these are suitable for any sector of industry. We even have infrared or laser thermometer to take measurements at distance, without contact.
-
Product
Solid State Relays
-
As well as being slim and thus saving panel space, The relays are very strong, have a large contact area and non-bendable pins. Connection to a PLC is easy and achieved faultlessly in a few seconds via click connectors. In addition, power switching in G3RV relays with DC outputs is managed by a MOSFET in the output, which has ideal heat dissipation characteristics.
-
Product
Handheld Tachometers
-
The handheld tachometer is a means of measuring revolutions within the industrial sector, either optically or mechanically. The handheld tachometer can be used for maintenance and calibration of machines that have moving parts. The principle is similar to a bicycle speedometer, where time will be measured until a wheel has completely turned. The handheld tachometer has two different measurement methods.The handheld tachometer may have a contact connection to the moving parts. Alternatively, the handheld tachometer works with reflecting marks. This will be secured on the moving part. As the laser strikes the reflecting mark during rotation, it will be reflected and detected in the handheld tachometer via a sensor. Rotation speed and speed can be seen on the handheld tachometer. The handheld tachometer may combine both possibilities (contact and non-contact connection). Next to the handheld tachometer you find other devices for measuring revolutions at PCE Instruments.
-
Product
160 Pin Female DIN to QuadraPaddle Flying Lead Cable, 48", 024070
VFL103124-048
Flying Lead Cable
Vendor Flying Lead (VFL) Cable, 160 Pin Female DIN to QuadraPaddle Leads, 24AWG Twisted Pair, 80 T/P's(1:2) 160 connection points, M2.5 x .45 fastener, CONN: 024070 WIRE: VPC, for PXI-2737, PXIe-2738 families, VPC Contact 610138216 - QP RCV (22AWG-28AWG) (5 AMP/25 mΩ MAX), 20" length.
-
Product
Gas Meters
-
At PCE Instruments you will find a professional quality gas meters for everyday use. The gas detector meets the requirements for personal safety and issued mainly for the detection of methane, hydrogen sulphide, carbon monoxide and oxygen levels (along with 50 other possible gases). The auto-calibration function allows for easy recalibration of the gas detector. Depending on the model, the gas detector has the ability to store data and later transfer recorded values to a computer.One accessory is the manual aspirator, with this device you can draw gas directly into the gas detection instrument via a 2 m long tube with which you will be able to measure gas levels without having to be in direct contact with the gas source or to be able to determine the levels of gas in places that are difficult to access. Furthermore, we have a fixed installation gas detector in many different models available.
-
Product
Low Resistance Ohmmeters
-
Some times know as Ducter testers, these are highly accurate, easy to operate instruments that measure resistance with resolution as fine as 0.1 micro-ohm. Digital micro-ohmeters and DLROs measure contact resistance of switch and circuit breakers, aircraft frame bonds, and rail and pipeline bonds just to name a few of the applications. Megger has models available for testing using test currents from 0.5 mA to 200 amps covering a multitude of applications that require precise low-resistance measurements.
-
Product
Integrated/Separated Explosion-Proof Ultrasonic Level Gauge
HR9100E
-
HighReach Measuring & Controlling System Co.,Ltd
1. Safety / use of die-cast aluminum alloy waterproof, explosion-proof shell; the explosion-proof grade of the instrument reaches Exd (ia) IIBT4 2. stable and reliable / we choose high-quality module key components from the power supply Part of The Circuit Design Stable and Reliable Devices CAN Completely Replace imported Instruments. 3. Patented Technology / Ultrasonic Intelligent Software CAN with Carry OUT Intelligent echo Analysis, the without the any the debugging and OTHER Special Steps, the this Technology has The function of Dynamic Thinking, Dynamic Analysis 4. High precision / sound wave intelligent patent technology owned by our company, so that The accuracy of the ultrasonic level gauge is greatly improved, the liquid level accuracy reaches 0.3%, it can resist various interference waves, the failure rate is low, the installation is easy, and the maintenance is easy. The instrument is a non-contact instrument and does not directly contact with liquid. Users can use this manual to calibrate the instrument. 6. The protection level of multiple protection/instrument reaches IP65; all output and input lines have lightning protection and short circuit protection.
-
Product
Plugbord
3662
-
VECTOR Electronics and Technology, Inc.
44 Gold plated edge contacts (22 each side)on 0.156"(3.96mm) centers.No circuit pattern edge contacts only.Unrestricted component placement over entire board surface
-
Product
Calibration Equipment
-
Tempsens offers a complete range of temperature calibration types of equipment for calibration of Contact Type Sensors (Thermocouple, RTD) and Non-Contact Type Sensors (Pyrometer). Our Calibration range is from -196°C to 3200°C
-
Product
High density PCB connectors
MHD/MDD/MDP Series
-
Smiths Interconnect's MHD/MDD/MDP series is an ESA qualified, high density board to board and board to wire interconnect available in up to 400 positions, with available insulators to accommodate coax and power contacts.
-
Product
Spiral Antenna UHF Trafo
-
UHF Spiral antenna is a partial discharge sensor designed to receive electromagnetic (EM) emissions from a PD occurring in the monitored asset. It is a broadband antenna with a flat response which makes Spiral antenna suitable in a number of different applications. It has been optimized to operate in a frequency range typical for PD activity and it was designed to provide maximum sensitivity and high gain. Its compact and robust design (passive sensor) makes Spiral antenna the optimal sensor for direct installation on high voltage Transformers. It can be virtually applied in any electrical equipment provided that it has apertures or EM transparent surfaces. Contact our sales department for consulting.
-
Product
Protective Cover, G18, ITA
410112541
Protective Cover
The ITA Protective cover is made of aluminum making it very rigid to protect your contacts and modules when the ITA is not in use.
