10 Gigabit Ethernet
Ethernet transfer rate > 1.25 gigabits per second. Also known as: 10GE, 10GbE,10 GigE
-
Product
NI-9222 , ±10 V, 500 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module
781397-01
Voltage Input Module
±10 V, 500 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The NI‑9222 performs differential analog input. This module is well suited for applications such as ballistics, impact, and blast wave testing. The NI‑9222 can sample at the maximum sample rate per channel while the module next to it samples at a much slower rate, which is ideal for mixed-measurement test systems. There are two connector options for the NI‑9222: a 10‑position screw terminal or a 25‑pin D‑SUB connector.
-
Product
cDAQ-9191, 1‑Slot, Ethernet and 802.11 Wi‑Fi CompactDAQ Chassis
781497-01
Chassis
1‑Slot, Ethernet and 802.11 Wi‑Fi CompactDAQ Chassis - The cDAQ‑9191 is a Wi‑Fi chassis designed for small, remote, or distributed sensor measurement systems. The chassis controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. You can use this chassis with a combination of modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. You can send data from the cDAQ‑9191 to a host PC over Ethernet or IEEE 802.11 Wi‑Fi. The chassis also has four 32‑bit general‑purpose counters/timers built in. You can access these counters through an installed, hardware‑timed digital C Series module for applications that involve quadrature encoders, PWM, event counting, pulse train generation, and period or frequency measurement.
-
Product
Cable Assembly, Receiver, TriPaddle, 20", 10 Position Combicon and 4 Position Omnimate
540295010101
Cable Assembly
Cable Assembly, Receiver, TriPaddle, 20", 10 Position Combicon and 4 Position Omnimate
-
Product
PXI-2512, 7-Channel, 10 A PXI Signal Insertion Switch Module
778572-12
Signal Module
7-Channel, 10 A PXI Signal Insertion Switch Module—The PXI‑2512 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXI‑2512 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls
-
Product
PXI Solid State Multiplexer Module, Single 6-Channel, 10 A
40-666B-012
Multiplexer Module
The 40-666B-012 is a single 6-channel 10A MUX and is part of our range of high current multiplexers occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each multiplexer channel can support 10A of continuous current and switch up to 200V signals. The switches can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
Product
IQ Data Bandwidth Up To 10 GHz
S93052B
-
Send wideband IQ data (up to 10 GHz) to PathWave 89600 VSA software running on PNA/PNA-X/PNA-L network analyzers
-
Product
Low-Barrier Schottky Diode Detector, 10 MHz to 26.5 GHz
33330C
-
The Keysight 33330C low-barrier schottky diode detector has been widely used for many years in a variety of applications including leveling and power sensing. It offers good performance and ruggedness. Matched pairs (Option 001) offer very good detector tracking.
-
Product
10-32 Coaxial Male to 10-32 Coaxial Male, 50 Ohm, 10 ft. cable
786659-01
Coaxial Cable
10-32 Male to 1-Pin 10-32 Male, 50 Ohm Coaxial Cable - The 1032CoaxialM-1032CoaxialM Cable connects data acquisition (DAQ) and control devices such as C Series I/O modules.
-
Product
2-Port SFP Gigabit Base Ethernet Card With HSR/PRP
ECU-P1524PE-B
-
PCIe or embedded module supporting dual 1000Mbps fiber connections, designed for high-availability networks.
-
Product
DP Range Broadband Power Amplifiers 10 kHz - 250 MHz
DP Series
-
Class A solid stateBroadband (instantaneous single band): 10 kHz 250 MHzTypical output power : 1000 W CWLinear output power (1 dB compression) guaranted with harmonics <-20dBc:P1dB>600 W and H<-20 dBcAir cooling: self contained fansCan operate in full mismatch conditions without damageReliable, efficient and robust19" Cabinet on wheels3 years standard warranty
-
Product
Ethernet Network Adapters
-
Available in PCIe NIC and OCP mezzanine 2.0 and 3.0 form factors, Broadcom’s Ethernet network adapters support configurations ranging from 1G to 200G, and utilizing both optical and copper connectivity.
-
Product
sbRIO-9222, Non-Enclosed, ±10 V, 500 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module
785479-01
Voltage Input Module
Non-Enclosed, ±10 V, 500 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The sbRIO‑9222 performs differential analog input. This module is well suited for applications such as ballistics, impact, and blast wave testing. The sbRIO‑9222 can sample at the maximum sample rate per channel while the module next to it samples at a much slower rate, which is ideal for mixed-measurement test systems. There are two connector options for the sbRIO‑9222: a 10‑position screw terminal or a 25‑pin D‑SUB connector.
-
Product
96-Pin Female DIN to 67-Pin Female Screw Terminal, 10 V, PXI Module Mount Terminal Block
781349-01
Terminal Block
NI TB-4353 Isothermal Terminal Block for PXIe-4353
-
Product
Dual-Port 1G PCIe Ethernet NIC
BCM5720
-
The BCM5720 PCIe NIC is a 13th-generation 10/100/1000BASE-T and 10/100/1000BASE-X Ethernet LAN controller solution for high-performance server and networking applications. The host interface supports a separate PCI Express function for each LAN interface. The BCM5720 includes I/O Virtualization (IOV) features such as 17 receive and 16 transmit queues, and 17 MSI-X vectors with flexible vector-to-queue association.
-
Product
Ethernet FPGA Mezzanine Card
-
Sundance Multiprocessor Technology Ltd.
Quad Gigabit Ethernet FPGA Mezzanine Card that can be integrated with the EMC2.
-
Product
NI-9223, ±10 V, 1 MS/s, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module
781398-01
Voltage Input Module
±10 V, 1 MS/s, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The NI‑9223 performs differential analog input. This module is well suited for applications such as ballistics, impact, and blast wave testing. The NI‑9223 can sample at the maximum sample rate per channel while the module next to it samples at a much slower rate, which is ideal for mixed-measurement test systems. There are two connector options for the NI‑9223: either four, 2‑position screw terminal connectors or four BNC connectors.
-
Product
2 Channel 10 bit 4GS/s Digitizer
V1761
-
The V1761 comes in a VME form factor with 2 input channels. The communication to and from the board is provided through VMEBus and Optical Link interfaces. It can record fast signals from fast organic, inorganic and liquid scintillators coupled to PMTs or Silicon Photomultipliers, Diamond detectors and others, and save them with high efficiency and precision for offline advanced timing analysis.
-
Product
PCIe 4.0 Ethernet Controller
BCM57502
-
The BCM57502 50G PCIe 4.0 Ethernet Controller builds upon the success of the widely deployed NetXtreme E-Series architecture by combining a high-bandwidth Ethernet controller with a unique set of highly optimized hardware acceleration engines to enhance network performance and improve server efficiency.
-
Product
PXI 8 Slot BRIC 440x4 1-Pole (10 sub-cards)
40-562A-121-440X4
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PCIe 3.0 Ethernet Controller
BCM57414
-
The BCM57414 50G PCIe 3.0 Ethernet controller builds upon the success of the widely-deployed NetXtreme E-Series architecture by combining a high-bandwidth Ethernet controller with a unique set of highly-optimized hardware acceleration engines to enhance network performance and improve server efficiency.
-
Product
8/4-Ch, 14-Bit, 10 MS/s Per-Channel Simultaneous Analog-Input PCIe DAQ Card
PCIE-1842
-
8 or 4 x Simultaneously Analog Inputs, up to 10 MS/s14-bit resolutionSupports digital and analog triggersWide input range up to 20 Vpp (±10 V range)Onboard FIFO memory (65,536 samples)
-
Product
Regenerative Power System, 500 V, 40 A, 10 kW, 200/208 VAC
RP7952A
DC Power Supply
The RP7952A regenerative power system is a single output, bi-directional, regenerative DC power supply with highly integrated safety features that protect both your people and your device under test. The regenerative capability enables the energy normally consumed to be returned to the grid cleanly, saving costs associated with energy consumption and cooling.
-
Product
10 MHz to 6 GHz LAN Wide Dynamic Range Average and Peak Power Sensor
L2061XA
Power Sensor
The Keysight L2061XA is a fast, accurate and wide dynamic range 10 MHz – 6 GHz LAN peak power sensor.
-
Product
PXI Single 10 Channel MUX, XLR Connectors
40-735-902-S2
Multiplexer Module
The 40-735 data communications multiplexer is designed for switching the data lines of serial interfaces (RS232, USB). Careful attention to the design of the module ensures that the switching system minimizes its impact on the transmission distance of USB1.1 interfaces. The MUX is available in 36:1 or 18:1 formats and enables a single source of serial data to be switched to one of 36 or 18 devices under test. This allows the data source to load information to, or receive information from, the device under test. The 36:1 version can be software configured into two independent 18 way MUXs enabling two separate sources of serial data to be connected to separate banks of 18 devices. The module is ideal for performing bulk testing of any device that relies on a serial data communications port to load software or control the device operation. It can also be used for a variety of other applications where ever a 2-pole low power MUX is required.
-
Product
NI-9252 , ±10 V, 50 kS/s/ch, 24-Bit, 8-Channel C Series Voltage Input Module
786782-01
Voltage Input Module
±10 V, 50 kS/s/ch, 24-Bit, 8-Channel C Series Voltage Input Module - The NI-9252 is an 8-channel analog input module for CompactDAQ and CompactRIO systems. Each channel provides a ±10 V measurement range and 24 bits of resolution at a 50 kS/s sample rate. The NI-9252 features a … number of programmable hardware filters. By choosing the specific Butterworth and comb filters for your application, you can significantly reduce the noise in your system.
-
Product
Electrical Penetrator with High Pressure Barrier, Rated at 10 kV and 250 A
P10-250 Electrical Penetrator
-
For higher subsea power requirements, the P10-250 from Teledyne ODI is designed to provide reliable barrier protection at extreme pressures and temperatures. The penetrator extends through a wall or bulkhead and connects to medium voltage cables to supply an external power source. In electric submersible pumping (ESP) applications, the penetrator transfers power to the motor while maintaining a pressure barrier between the motor and the seawater.
-
Product
3U CompactPCI Serial 5-slot SSL w/ RTM w/ Ethernet
1CPCIS-305-L210
-
3U CompactPCI Serial Backplane with 5 CompactPCI S.0 slots, system slot left, with rear IO : 1x CompactPCI S.0 CPU slot, 4x CompactPCI S.0 peripheral slots, with connectors for RTMs (RearTransition Modules) in slots 2 to 5, Ethernet full mesh.
-
Product
Hardware Modules for PXI, PCI, PCI Express, USB, Ethernet, VME, and VXI
MIL-STD-1553
-
Avionics Interface Technologies
MIL-STD-1553 hardware modules for PXI, PCI, PCI Express, USB, Ethernet, VME, and VXI provide advanced features and functionality to support even the most demanding test and simulation applications.
-
Product
NI-9147, 4-Slot, Zynq-7020 FPGA, Ethernet CompactRIO Chassis
783496-02
Chassis
4-Slot, Zynq-7020 FPGA, Ethernet CompactRIO Chassis - The NI‑9147 is a rugged Ethernet chassis that you can use to add C Series I/O modules to any standard Ethernet network. You can program the chassis using Scan Mode for fast expansion of your real-time system or using the onboard FPGA for inline processing and high-speed I/O and control. With the NI‑9147, you can add high-performance I/O to your PC-based application or expand your CompactRIO, PXI, or industrial controller application.
-
Product
sbRIO-9264, Non-Enclosed, 25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module
781119-01
Voltage Output Module
Non-Enclosed, 25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module - The sbRIO‑9264 is a simultaneously updating analog output module that accommodates higher‑channel‑count systems. Higher density modules conserve chassis space, which leaves room for other measurement types. Each channel has its own digital‑to‑analog converter. The spring-terminal version of the sbRIO‑9264 uses a 36‑position connector for the output channels, and each channel has a ground connection. Non-enclosed modules are designed for OEM applications.
