-
Product
Rugged Ethernet System Supporting up to Four Independent 8000 Family Avionics Communication Modules
ES-9810/xx
-
The ES-9810/xx is a rugged ethernet system supporting up to four independent 8000 family avionics communication modules, allowing multiple different protocols to be mixed and matched in a single system. Modules available include MIL-STD-1553, MIL-STD-1760, MMSI, ARINC-429, ARINC-708, ARINC-717, Serial, Discrete and CAN bus.The ES-9810/xx is supplied with C drivers, including source code. Mating connectors and cable adapters for I/O connection can be purchased seperately.
-
Product
NI CAN Cable, No Term, High-Speed/FD/Low-Speed, D-Sub 9-Pin F, 1m
193128-01
-
9-Pin Female D-SUB to 9-Pin Female D-SUB CAN Cable - The DB9F-DB9F CAN Cable connects C Series CAN Interface Modules, C Series LIN Interface Modules, or C Series Multiprotocol Interface Modules to devices, breakout boxes, and accessories. It is sometimes referred to as CAN Cable (single termination or no termination). This cable is compatible with high-speed, flexible data-rate, and low-speed/fault tolerant CAN signals, available with or without termination, and in different lengths.
-
Product
NI-9853, CAN Interface Module
780178-01
CAN Interface
2-Port, High-Speed C Series CAN Interface Module—The NI‑9853 is a high-speed Controller Area Network (CAN) interface for developing FPGA-based applications with the NI‑RIO driver on CompactRIO. The NI‑9853 is ideal for low-level FPGA‑based control and triggering applications that are programmed using the LabVIEW FPGA Module. The NI‑9853 is ideal for byte-level manipulation of CAN frames using the LabVIEW FPGA Module. The NI‑9853 is only compatible with CompactRIO systems.
-
Product
Power PC 8641D Based Board
MS 2501
-
Ethernet Port : 4 Channel (1GBPS)CAN Port : 1 ChannelMIL1553B : 1 Channel (Dual redundancy)RS232 : 4 Channels (512 byte FIFO, 4MBPS)RS422 : 12 Channels (512 byte FIFO, 4MBPS)JTAG : Flash Programming and Debugging
-
Product
Reliable CAN Measurement Technology
CNT evo CAN MM Series
-
The CNT evo is a high-precision measurement module designed for measuring frequencies, pulse widths, incremental displacement measurements, rotation angles, position measurement, event counting and period measurements.
-
Product
2x (1 to 8) +1X (2 to 1) 50 Ohm 2.5GHz RF Multiplexer Terminated
YAV92501
Multiplexer Module
2x (1×8) Mux + 1×2 + 2x Pass trough 30Vac/dc, 10W Max Max current 500mA Control port CAN o Ethernet (con Ethernet to CAN Gateway) Dissipative
-
Product
NI-9881, 1-Port C Series CANopen Interface Module
781673-02
Interface Module
The NI‑9881 is a high-speed CANopen interface for developing CANopen applications in LabVIEW software on CompactRIO hardware. CANopen is the application layer that sits on top of the CAN physical layer often used for industrial automation … applications. It was designed for motion-oriented machine control networks, such as handling systems, but now it is used in a variety of applications, including medical equipment, off-road vehicles, maritime electronics, public transportation, and building automation. The NI‑9881 can transmit/receive process data objects (PDOs) and service data objects (SDOs) according to CiA‑DS 301. The NI‑9881 is compatible with only CompactRIO systems.
-
Product
Profibus Gateway for Woodward Easygen Genset Controls and LS-5 Controls
ESEPRO
-
ESEPRO is a Profibus gateway specifically designed to interface Woodward's Easygen series genset controls with Profibus-DP networks. It interfaces via the CAN bus with the Woodward controls and is easy to configure using standard Profibus configuration tools like Simatic Manager.
-
Product
Real-time DAWN Mini Streamer™
-
The DAWN Mini Streamer™ transfers OBD, CAN and J1939 data from a car or heavy duty vehicle to a mobile device (tablet, smart phone or PC) in real-time. Data is transferred using WiFi, so the technician can be in or outside of the vehicle.
-
Product
Digital Indicator
ZET 7178
-
The Digital indicator ZET 7178 is intended for indicating the data transmitted via the CAN network by the ZETSENSOR series digital sensors.
-
Product
Digital Meteorological Sensor
ZET 7123
-
Digital meteorological sensor ZET 7123 is a measuring unit with two in-built sensors, one of which is used for measuring relative humidity and temperature, and the other one – for atmospheric pressure measuring. ZET 7123 meteorological sensor measuring unit converts signal from the sensing elements to temperature, humidity, and pressure values. The obtained values are transmitted via CAN interface and displayed in the measurement units set by the user.
-
Product
High Flexibility Test Controller Card
TCC 1800-UE
-
The TCC1800-UE Test Controller Card is a generic control board for production testing of printed circuit boards (PCBs). The board is controlled by a command language on a PC to which it is connected via Ethernet.The TCC1800-UE is designed to work with positive voltages up to 24V. The card provides extensive IO: Analog and digital interfacing, counters, PWM outputs, bidirectional I/O, ethernet-, CAN, USB, SPI and I2C interfacing.
-
Product
Analysis Tool for ECU Networks and Distributed Systems
CANape
-
The primary application area of CANape is in optimizing parameterization (calibration) of electronic control units. During a measurement process, you can simultaneously calibrate parameters and record signals. The communication between CANape and the ECUs takes place via protocols such as XCP or via microcontroller-specific interfaces with the VX1000 measurement and calibration hardware. CANape supports various ADAS sensors such as radar, LIDAR and video. Combined with high-performance hardware, CANape can store multiple gigabytes of data per second. Calibration data management and convenient measurement data evaluation including data management as well as reporting make CANape a complete tool for ECU calibration. Of course, CANape also provides access to bus data, diagnostic data and analog measurement data.
-
Product
Value-added Module With COM/CAN/DIO And 3 PCI Express Mini Card Slots
VAM900
-
*1 4-wire isolated RS-232/422/485, 1 isolated CANBus 2.0A/B, 1 isolated DIO 8-in/8-out*Swappable modular design*Maximize I/O flexibility*2kV (COM & CANBus)/1.5 kV (DIO) isolated protection*Designed for tBOX300/500 series*EN 50155 certified; CE, LVD and FCC compliant
-
Product
Analysis Tool
CANalarm
-
The CANalarm is a low priced analysis tool that can be installed in the bus permanently. It makes it possible to build up a separate and redundant monitor without change of configuration and program of the master controller. It works passive and is therefore non reactive
-
Product
USB2.0 Module With 2 CAN Bus Nodes ARINC825 Compliant For Testing & Simulation of Avionic ARINC825/CAN Bus Systems
APU825-2
System
USB2.0 module with 2 CAN bus nodes ARINC825 compliant for testing and simulation of Avionic ARINC825/CAN bus systems.
-
Product
CAN + OBD Network Data Converter
NC1
-
Get RPM, Speed, Absolute throttle position and many other vehicle parameters in real-time from your vehicle's standard OBD connector. Works with ANY OBD2 equipped vehicle. Works with ANY data acquisition equipment.
-
Product
Chassis
-
Highest channel densityUser exchangeable TRIONTM modulesfor analog, digital, counter, CAN inputsSelectable resolution 16 or 24 bit
-
Product
ARINC825 (CAN Bus) Test & Simulation Module for PCI With 2 Or 4 CAN Bus Nodes
ACP825-x
Simulator
ARINC825 (CAN bus) Test & Simulation module for PCI with 2 or 4 electrically isolated CAN bus nodes operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s. The ACP825-x PCI card can work either with full functionality as an active CAN node for testing and simulating or in Listening Only mode for monitoring and recording purposes.
-
Product
Communication Data Logger
LE-270A
-
LE-270A is a Communication Data Logger, which records CAN/LIN communication logs in the SD/SDHC card for long hours. Using with a PC, it performs as a CAN/LIN protocol analyzer, and monitors data on the PC at real time (Line Monitor). Using without a PC, it performs as the CAN/LIN data logger, and saves data in the SD/SDHC card. It has two High-speed CAN transceivers, two Low-speed CAN transceivers and two LIN (TJA1020) transceivers. It monitors two channels of CAN or LIN, or one CAN and one LIN transceivers. In addition, four channels of Analog/Digital signals can be recorded.
-
Product
Switched Power Distributed Module, CAN Control
H730008xS
Power Module
The intelligent Power Distribution Unit (PDU) H7300.08xx has two main functions: Distributing the power to each device in a system Switching on the devices sequentially, in order to minimize the inrush current from the switched power supplies, that might affect the contactors.
-
Product
PCI-8531, 1-Port, CANopen Interface Device
781060-01
CAN Interface
The PCI‑8531 is a high-speed CANopen interface for developing applications with the NI‑Industrial Communications for CANopen driver. CANopen is the application layer that sits on top of the CAN physical layer often used for industrial automation … applications. CANopen was designed for motion-oriented machine control networks, such as handling systems, but now it is used in a variety of products and applications, including medical equipment, off-road vehicles, maritime electronics, public transportation, and building automation. The PCI‑8531 can transmit or receive process data objects (PDOs) and service data objects (SDOs) according to CiA‑DS 301. It also features a batch SDO editor with EDS file integration and LSS services support for slave node configuration.
-
Product
FMC Mezzanine Dual or Quad Canbus
NES-FMC-CAN
-
Sundance Multiprocessor Technology Ltd.
This is a Dual or Quad CANbus with autotest capabilities that can be used on a wide range of carriers, Standalone, PCIExpress, CompactPCI, VPX, CompactPCI Express, AdvanceTCA and AMC.
-
Product
32-Ch SPDT 2A-240VAC 24VDC Switching
YAV90133
Relay
32 relays, 5A Switching 5A 250Vac. Up to 1250VA 28 Relays SPST Mux. 1 a 4 relays CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
Product
InfiniiVision Oscilloscopes
3000A X-Series
-
100 MHz to 1 GHz, DSO and MSO modelsView time-correlated digital content with16 digital channels (MSO)Modulate signals within the scope with WaveGen, built-in 20 MHz function generator (optional)Quickly characterize signals with the built-in 3-digit voltmeter and 5-digit counter option Decode serial busses faster with hardware-based serial analysis options for CAN, LIN, IC, SPI, RS232 and more Protect your investment with full upgradability
-
Product
Ultra-Broadband Light Soure
Cannon
-
Cannon provides a turnkey portable source of broadband laser pulses without reqiring any user-adjustments to the fiber coupling. Optical Spectrum - 1000 - 1900 nm.
-
Product
Measuring Systems For Beverage Can Manufacture
Ring- And Punch-Polisher
-
Optik Elektronik Gerätetechnik GmbH
Polishing mashine for ironing rings and punches used in 2-piece can making.
-
Product
Measuring Device
CAN-Bus Tester 2
-
The CAN-Bus Tester 2 is a widely used measuring device for control of bus parameters. The success story starts already in year 2002 with the first model. The hardware was completely redesigned in version 2. The corresponding software is still developed and has been enhanced with extensive updates.
-
Product
The Automation Hardware
CandyBox
-
Supports any infrared based deviceAutomate unlimited devices from one accountAutomate remote devicesPrecise, collision-free infrared signal targetingBuilt-in recorder for infrared codesExtremely easy and user-friendly setup8 or 40 independent control portsBrowser based virtual remote controlRecord and replay key sequencesEmulate power cutsAPIs coming soon
-
Product
Internal DAQ Cards
PCIe, PCI, PC/104, CAN
-
PC data acquisition cards are particularly suitable for stationary measurement applications. Outstanding in this category are the PCI(e) multi-function cards PCI-BASEII and PCIe-BASE on which you can plug different measurement and control modules to optimize the price-performance ratio.
