Leakage Current Testers
-
Product
Pitot-Static Tester
PS-425
-
The PS-425 Pitot-Static tester is a low-maintenance, digital tester that is fully portable. The PS-425 is powered by an internal rechargeable 12 volt battery (included in purchase), which enables the test set to be used completely independent of any external power source. A connector is provided for an external 12 volt DC power adapter (included). The PS-425 incorporates the altitude, VSI, and airspeed in one single display. The PS-425 is designed and priced for non-RVSM markets, and includes two quick-connect hoses, 12 VDC power adapter, calibration certificate, and a limited 2-year warranty. This product is ideal for performing simple go/no-go leak tests, as well as for general use as a low-end pitot-static tester.
-
Product
Analog Earth Tester
FT3151
-
Earthing or grounding of electrical equipment is essential to maintain safety, protecting lives, as well as prevent damage to equipment. • Three-electrode method, Two-electrode method (Simple Measurement) • Wide measurement range for 0 to 1150 Ω, based on EN standard •Switchable measurement frequency to reduce the effects of power supply harmonics • Dramatically faster setup: Comes with improved grounding rods and cord winders. CAT II 300 V
-
Product
AC and DC Current Sources
-
Programmable AC and DC current sources that provide precise, low noise, stable currents for a number of applications.
-
Product
Outdoor Exposure Tester
OET
-
A comprehensive analysis of PV modules includes many different parameters. Determining the normal module operating temperature (NMOT), incidence angle effects and comparing soiling effects on different modules up to the initial degradation of PV modules are all parameters that can be analyzed with our outdoor exposure tester. The tester comes with up to twelve electronic loads installed in a 19" rack. The loads have two main functions: maximum power point tracking (MPPT) and IV curve tracing. For the advanced analysis, it is possible to change between these two modes within one test. In the normal operation mode, the electronic load keeps the module under MPP and each predefined interval an IV curve is traced. The entire tester comes with all necessary sensors such as temperature sensor, which can be attached to the module to determine the NMOT temperature like defined in IEC 61215 (MQT 05) and IEC 61853-2. The irradiation sensor is also included. In combination with our tracking system P2, it is also possible to determine incident angle effects of the PV module. It is also possible to connect other irradiation sensors for diffuse and direct irradiation, which helps to understand the behavior of the module in different irradiation conditions. An optional albedo meter is a powerful tool for the analysis of bifacial modules. The entire graphical user interface is web based and offers the possibility to access the system from the all computers in the network.
-
-
Product
Current Probe Calibration Fixtures
-
Calibration fixtures are used for calibration of Coupling Loss/Transfer Impedance of current probes and BCI probes, as well as for the calibration of test levels for conducted immunity/susceptibility tests using BCI probes.
-
Product
Relay Tester
-
Beijing GFUVE Electronics Co.,Ltd.
Assists in the inspection, installation, and repair of assigned electro-mechanical controls and equipment systems.
-
Product
Split Core Current Transformers
-
Application:Watt Transducer, Current Transducer, KWH Meter, Demand Meter, Power Factor Meter, Current Sensing Relays, Energy Management SystemsContinuous Thermal: Rating 1.25 at 30° C, 1.0 at 55° C Standard 5-amp secondary. Others available.
-
Product
Noise And Vibration Tester
-
In a miniaturized motor, even the slightest rumbling sound that occurs during rotation can be a cause for failure.
-
Product
Precision Current Preamplifier
SIM918
-
Stanford Research Systems, Inc.
The SIM918 Current Preamplifier is ideal in applications in which the input offset voltage must be kept to a minimum. The DC voltage difference between the two inputs (current input and voltage bias) is accurately measured every 2 seconds, and is nulled.
-
Product
AE Valve Leakage Detector
SVLD1
-
Through acquisition, processing, and calculation of acoustic emission signal of the valves, SVLD1 could generated root-mean-square voltage (RMS), average signal level (ASL) and power (P) parameters as which could judge the leakage. Meantime, you can pre-calibrate the leakage quantity for the specified valve, and calibration curve of parameters and leakage could be calculated by SVLD1, so as to give the valve leakage reference value during the test.
-
Product
ECM PCB Tester
MS 1105
-
*Used for testing of DAWN RWR PCBs in Jaguar Aircraft*19” Rack mountable with built-in wide range of IO signals *Used in 4th line servicing of PCBs*Used in LRU and system level testing*Detects 100% fault coverage including track faults*Adaptability with off-the-shelf instruments
-
Product
IV Tester System
PET-CC
-
Application ■Mono crystalline silicon (Si) ■Multi crystalline silicon (mc-Si) ■Amorphous silicon (a-Si) ■Gallium arsenide (GaAs) ■Gallium indium arsenide (GaInAs)
-
Product
Cable Tester
LX-560A
-
Shenzhen Lian Xin Technology Co., Ltd.
Cable/Harness Tester (low-pressure type) features its capability of testing the components inside the wire, the test speed more than double faster than that of the traditional wire testers, and the provision of such functions as unilateral, turn-on resistance editing, and spot metering color editing.
-
Product
Buchholz Hardness Tester
3095
-
Measuring a coating’s hardness using the indentation method, the Elcometer 3095 Buchholz Hardness Tester consists of a bevelled disc indenting tool that is fitted into a stainless steel block exerting a constant test load of 500g (17.6oz).
-
Product
Air Leak Testers
-
Leak testing is an important quality control test in the manufacturing industry. Since there is no such thing as a completely leak-free component, the key is to determine what leak rate is acceptable in order to manufacture products that are safe and adequate for the customer’s needs. Once the consequence of a leaking product is determined, it can help guide what type of test method is most practical based on budget and technology required to perform testing at the determined specifications.
-
Product
Spring Back Tester
HTJ-16
-
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.3-2008/IEC60851-3; Inspection standard: JB/T4279.4-2008Used to measure the spring back characteristic of enameled round wires with nominal conductor diameter of between 0.080mm and 1.600mm;Number of winding turns: 5 turns and a halfStop accurately at zero position of the scale after automatic windingAs soon as the value of spring back angle stop counting, the dial will stop to rotate immediately, so that the value displayed on LED and read on the dial are the same.Sensor is unnecessary to be adjusted for samples of different specificationsCoils loosen slowly during spring back, no action of spring back or jump suddenly.Application of SCM control allows for fast operation and strong anti-interference capacity;
-
Product
Epstein Tester
S21 and S21R Series
-
Incoming material inspection can be very useful where strict quality standards are maintained. It saves a lot of processing cost since lossy material is inspected at the entry level before it goes to production level. Epstein Stack testing is one of the oldest and widely used methods for electrical sheet testing.
-
Product
Battery Testers
-
La Marche Manufacturing Company
This patented battery tester has the capability to store battery discharge curve as a benchmark to analyze battery health trends.
-
Product
Waterproof Salinity Tester
SaltTestr 11
-
Swtiching between °C and °F is now a breeze with the simple press of a button. Direct temperature readout on the tester saves you the trouble of an additional thermometer.
-
Product
High AC Current Capacitor
LC1/LC2/LC3-RNM
-
Induction Heating Processing Equipment, Electric Current Welding, High Power Resonant Circuits, Motor Controls; Oscillating, Bypass, Coupling circuits, High AC Current applications, High-Frequency AC Filter and Medium Frequency Power applications.
-
Product
Action Counter Tester
-
Weshine Electric Manufacturing Co., Ltd
Lightning strike counters of lighting arrester measure lightning strikes by the induction of current and do not require the use of any external power source. Weshine invented Lightning-strike-counter Tester (VS-451) is used of verify that if strike counter is correctly mounted and connected. As well as output current with sensitivity of 0.01 mA to correct leakage ammeter.
-
Product
Plunger Tester
PL2003
-
Designed and manufactured in accordance with ASTM F414, DOT571.109, F870 & JIS D4230 standards. New generation of PL-2000X series Plunger Testers, equipped with servo-hydraulic system to control the testing speed, are available fpr customers to select the suitable model. Test functions including Radial elasticity test, Tread footprints test, Tire dimension test, Bead unseating test, Lateral elasticity test and Pressure distribution analysi for Footprints.
-
Product
Moisture Management Tester
-
Sataton Instruments Technology CO., Ltd
Moisture management tester (MMT) is the tool for the measurement, evaluation and classification of liquid moisture management properties of textile fabrics. By testing the changes in electrical resistance of textiles placed between two horizontal electrical sensors with concentric pins, the tester can calculate fabric liquid moisture content changes that quantify dynamic liquid moisture transport behaviors in multiple directions of the specimen. The software of tester can grade the liquid moisture management properties of a fabric by using the predetermined indices. The tester is used to determine the liquid moisture management properties of knitted, woven and nonwoven textiles, and also can be used to test the one-way transport capability of diapers.
-
Product
Pitot Static Tester
ADSE 550
-
The ADSE 550 pitot static tester, housed in a plastic carrying case, is a portable, self contained field tester designed to test aircraft pilot ans static systems for leaks as well as the operation and calibration of airspeed, altimeter, engine pressure ratio, manifold pressure indicators, and other vacuum or low pressure units. The tester consists of a hand-operated vacuum pump, a hand-operated pressure pump vacuum and pressure gauges, 5 control valves, an altimeter and an airspeed indicator. The package accessories include two 25-foot hoses.
-
Product
Flexible Rope-Type Current Probe
RCT1A and RCT5A
-
These probes have great bandwidth ensuring accurate measurement even with harmonically distorted wave shapes. For all RCT1A/RCT models, a NIST, NAVLAP, NPL (UKAS) factory traceable calibration certificate and certificate of conformance is supplied. UL/CSA approved materials are used throughout. Three phase and single phase flexible AC current sensors (rope sensors) are available for fast installation in confined spaces, eliminating the need for Electrical Supply Shutdown. Available outputs are 1A @ 2.5VA and 5A @ 0.5VA, this means long cable lengths from current sensor to signal conditioner allow these low VA ratings to be used, even when feeder cable to energy meter distances are large (up to 98 feet / 30 meters)
-
Product
Glow Plug Tester
7640
-
Peaceful Thriving Enterprise Co Ltd
The tester is able to help diagnosing the condition of glow plug without removing it from the engine. This tester is working for 12V system, tester can be energized by 12V vehicle battery directly.
-
Product
CDM testers
Scorpion
-
Scorpion opens a new generation of CDM testers. It is designed to meet the new JS-002 standard and features Contact First pulse delivery. This patent pending technique of Contact CDM (CCDM) meets the latest CDM standards with higher accuracy for device classification.
-
Product
Non-contact Io/Ior Leakage Clamp Meter
MCL-800IRV
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
・Safety by non-contact sensor, not touching live part directly (prevention of electric shock, short-circuit, etc.).・Easy to carry and operate, clamp CT + display part integrated type.・Measurable line current + leakage current + resistive leakage current by one unit.・Available direct voltage input at live part as ordinary.・Calculable insulation resistance value（MΩ）by voltage & current (only in case of using direct voltage input sensors)・Available measurement for 3P/4W star connection.
-
Product
Gas Permeability Testers
-
Gas Permeability Tester (Gas Transmission Rate Tester) is based on the differential pressure method and is professionally applicable to the determination of gas transmission rate of plastic films, composite films, high barrier materials, sheeting, metal foils, rubber, tires and permeable membrane.
