Source Code
-
Product
Sources & Converters
-
High reliability, low-phase-noise, high-coherence, large operational temperature range, exceptionally low g-sensitivity for high vibration and shock performance.
-
Product
Open Source Logic Analyzer
Logic Pirate
-
8 channels 256,000 Samples recording size 20 MHz sampling speed, can potentially be overclocked to 60 MHz No compromise on sample size when combining different speeds or number of channels Simple configurable edge detection triggers on all inputs (simple OR trigger) Configurable ratio of samples from before and after the trigger (rolling sample buffer) 5 V tolerant inputs (LOW-level voltage < 0.8 V, HIGH-level voltage > 2.0 V) About 500 kB/s transfer speed to the PC (256 kSamples take about 0.5 seconds) Data capturing can be stopped from the host software anytime Cross platform host software for Windows, OS X, and Linux DIY-friendly 0603 parts and SOIC packages used on a 2-layer board On board 3.3 V regulator can supply up to 400 mA to an external circuit Tiny 3cm x 3cm PCB Firmware updates via built-in USB bootloader Probe cables and acrylic case available from Seeed Studio Open source PCB (EAGLE) and firmware files
-
Product
500-1000W AC Power Source
CX-P150
-
Shenzhen Chuangxin Instruments Co., Ltd.
The AC power source is made by adopting microcomputer processing chip and high power device. It provides a stable pure sine wave and has voltage,
-
-
Product
Sound Power Reference Source
Qref
-
Precision omni-directionallity in all directions, horizontal and verticalplane. This source has a frequency range of application between 100 and8000 Hz (third octave bands) Despite only weighing 1.4 kg and having a diameter of 105 mm, it produces a maximum sound power level of Lw 104 dB.
-
Product
PCI POST Code Display
post4d
-
During power on self-test (POST), most PC BIOSes will write diagnostic codes to port 80h or port 84h (jumper selection). Use post4d to display these codes on a dual digit LED display. Additional LEDs indicate the status of the power supply rails. Convenient business card size.
-
Product
Programmable AC Power Source
LSP-500VAC
-
• Applied with the AC-DC-AC inverter technology and digital waveform synthesis & waveform feedback technology, low distortion power; • Applied with entire cycle high-precision measurement technology and high-speed sampling technologies, panel of instrument will directly and accurately displays the power output of the voltage, frequency, current, active power and power factor to achieve the integration of the source table; • Applied with SCM control and measurement technology, high intelligence; • Applied with zero output impedance technology, the output equivalent impedance is almost zero and further improve the stability of power supply; • Applied with isolated floating output technology, the power output and input have good isolation, floating output, conducive to make sure power itself safety and operator’s safety; • Perfect voltage, current anomalies and overheating protection, improve the reliability of power supply; • Applied with power limiting technology to avoid strong interference on the power grid and other electrical equipment, while facilitating reliable operation of the power supply itself; • The input voltage can be option via a toggle switch of panel mains 110V/220V; • The initial phase and end phase of the output voltage waveform can be set {0°-359° (±1°)}; • Measurement process can be programmed to control (1 to 50 memory groups, 1 to 9 steps for each memory group);
-
Product
Bench-Top Type ASE Light Source
-
ASE(Amplified Spontaneous Emission) light sources are low-coherent light sources ,which combines the both features of high intensity like laser and broad spectrum like LED. Output stability is greater than those of LD and LED, and therefore they are suitable for high accuracy measurement applications. With the use of rare-earth-doped fluoride fibers, the plentiful lineup of FiberLabs light sources includes the 540 nm-, 850 nm-, 1300 nm-, 1480 nm- and SCL-bands that other companies do not provide.They are the best light sources for FBG sensors, OCT, fiber optic gyroscopes, gas sensors, and fluorescence excitation, as well as for measurement of optical components. The bench-top type is easy to use as a stand-alone light source and the modular type is convenient for integration into equipments.
-
Product
Power Supplies and Sources
DC Power Supplies
-
DC power supplies are commonly used in electronics design, battery charging, electrical vehicle, research labs and education sectors. UNI-T offers both programmable and non-programmable power supplies with features such as low ripple and noise, constant voltage/current, overload protection, and more.
-
Product
Optical Light Sources
FLS200 Series
-
Shanghai Tarluz Telecom Tech Co., LTD
FLS200 Optical Light source could provide maximum 4 wavelengths in one unit, customer could select arbitrary four output wavelengths from 650nm, 850nm, 1300nm, 1310nm, 1490nm, 1550nm. The unit support Single mode and Multimode (50/125um or 62.5/125um MM fiber) optical cable in one unit. It could support FC, SC, ST, LC and 2.5mm universal optical connector.
-
Product
Ultra Stable Current Sources
6623A-PCS
-
Guildline Instruments 6623A-PCS Series of DC Precision High Current Systems introduces new patented designs to provide the best uncertainties of any DC high current sources (i.e. typically < 5 ppm at 1000 A) and the best in modularity.
-
Product
Forensic Light Source
CrimeScope CS-16-500W
-
The flagship of the SPEX Forensics Product Line, the CS-16-500W was designed for those departments that prefer the power and IR capabilities of 500W Xenon lamps.
-
Product
Four-Wavelength Laser Source
CA6017 Series
-
The CA6017 Can transmit with a wavelength-identification digital encrypted protocol, enabling the FHP2 power meter to automatically use the proper calibration wavelength. This feature reduces the need for communication between the two technicians and decreases the possibility of making mistakes
-
Product
Noise Source Family
347
-
The R347B waveguide noise source cover the R-band (26.5 to 40 GHz frequency range), while the Q347B model cover the Q-band (33 to 50 GHz frequency range), allows you to make accurate noise figure measurements on millimeter-wave devices.
-
Product
Multiple (8) Four Quadrant Power Source
PM0820
-
The PM0820 uses an onboard controller, which relieves the system CPU of performing many functions necessary for the module operation. The result is higher efficiency of the CPU and faster execution of the module commands.
-
Product
Laser-Driven Light Source (LDLS)
EQ-77
-
Based on the highly successful Laser-Driven Light Source (LDLS)technology, the EQ-77 offers the highest radiance and irradiance availablein a truly broadband white light source. The EQ-77 features a compact lamp house, with clean construction that ensures long life and ultimate stability. With a 170nm-2100nm wavelength range, and a choice of source dual-beam output or a single-beam output with retro-reflector, the EQ-77 is flexible for a broad variety of applications. Researchers using light for imaging and analytical spectroscopy in a variety of applications in the life sciences and materials sciences need light sources capable of providing extreme high brightness and power across a broad wavelength range.
-
Product
Amplified Spontaneous Emissions (ASE) Sources
-
The AP505xA series, high power ASE sources provide stable output power up to + 23dBm and broad flat spectrum over C+L band or T band. They enable effective and efficient measurements for component characterization or optical sensing. Finally, these products are proposed in friendly-user stand alone benchtop instrument with touch sensitive screen, GPIB, ethernet, RS-232 or USB controls.
-
Product
DC Constant Current Source
-
SCR ELEKTRONIKS have developed equipment namely“DC CONSTANT CURRENT SOURCE”. The system comprises of Constant Current Sources having ranges: 900A continues & 3000A short time at 8V maximum.
-
Product
Fixed Source PLL DRO Replacement
ESP Series 2.25” x 2.25” x 0.6”
-
*Connectorized Package *Exceptionally-Low Phase Noise *DRO Replacement *Optional Internal Reference *Robust Designs Available *Optionally Hermetically-Sealed
-
Product
Long Light Source
LM-A
-
The long light source is compatible with the LM-101 or the LMC-20. The light is supplied with a 50 watt tungsten halogen convection cooled light source which provides suffcient energy for use with narrow band pass filters or monochronomators in the wave length range of .35 to 2.5 microns. The light beam is chopped at 200 hz by a quiet, vibration free, synchronous motor. The housing also contains a secondary LED light source and detector for synchronization of the amplifier, plus an electro-mechanical shutter to block the light output when the instrument is zeroed. An internal collimating lens produces a narrow beam (<1") so the LM-A can be used in bell-jar and large coating systems.
-
Product
Code Coverage Tool
Testwell CTC++
-
Testwell CTC++ is the leading Code Coverage Tool for measuring Code Coverage on host and all embedded targets (even very small ones). The tool is compliant to Safety Standards. Hundreds of companies all over the world use Testwell CTC++ with great success. Testwell CTC++ is the first choice for companies which have to achieve and to proof high code coverage in aerospace, automotive, transportation, healthcare and other industries.
-
Product
Point Source
MK Series
-
The MK Series is EAW’s state-of-the-art, passive, two-way systems specifically engineered for permanent installation.
-
Product
Monochromatic, Fiber-Coupled LED Light Sources
-
LED light sources in the LS-MC1 series provide a constantly growing selection – currently amounting to over 20 – of narrow band single wavelength LEDs with a bandwidth of 15-50 nm FWHM, allowing precise work in a defined wavelength range. As a result of optimized optical coupling into the optical fiber – as with all of our light sources – with our LS-MC1 series we have achieved the highest possible luminance. The advantage of directly emitting monochromatic LEDs is their very high level of efficiency, because the entire radiated output is in the useful wavelength range.
-
Product
PathWave BenchVue AC Source Control Software
BV0026B
-
The PathWave BenchVue AC source control software controls and analyses your AC source measurements to understand the impact of events related to power draw.
-
Product
Source Systems AC
-
The power sources of MTS-series based on digital amplifier modules combined with frequency generator and reference device are the MTS source system. Single-phase systems (MTS1xx) or three-phase systems (MTS3xx) from 1 to more than 40 test positions are available.
-
Product
Sound Source And Power Amplifier
-
Designed for acoustic application, with strong signal transmission capability and flexible measurement.
-
Product
Laser Source
TW3109
-
Techwin(China) Industry Co., Ltd
can provide 1 to 4 output wavelengths to meet specific requirements, including the 650nm red source and the 1310/1550nm wavelengths for single mode fiber or the 850/1300nm wavelengths for multimode fiber, as well as other wavelengths according to customer needs. Together with the TW3208 optical power meter, it is a perfect solution for the fiber optic network characterization.
-
Product
Light Source
LS-BA
-
Balance Light Source (LS-BA) is designed for transmittance and absorbance measurement with color information. Halogen Light source provides the stable and smooth wide-band spectral output. It’s proper for most visible to near infrared range measurement. The efficiency of blue region will be enhanced by extra two blue LEDs.
-
Product
Uniform Light Sources With Continuous Emission Spectrum
-
Tungsten halogen lamp based uniform light sources with options like manual or remote control variable intensity or monitor detectors.
-
Product
Wheelset Axle Identification Using 2D DMC Codes
-
Automation of the process of identifying the axles of wheelsets at the site of the final inspection by the two-dimensional codes applied to them. The system should provide automatic search, reading and recognition of a two-dimensional code punching on the axis. The recognition result should be automatically transmitted to the ultrasound diagnostic unit as an identifier of the controlled object.
