Power Factor
measures true power over apparent power.
-
Product
AC Load Bank (Resistive & Inductive)
K-1000 Resistive & Inductive
-
Kongter Test & Measurement Co., Limited
Kongter resistive & inductive AC load banks are used to simulate the motor loads or other electromagnetic devices working at their rated power factor. Many backup generators and turbines are rated at 0.7, 0.8 or 0.85 power factor and need to be commissioned at nameplate capacity using a combination of resistive and reactive load to fully qualify their operating capability. Using a resistive & reactive load bank enables comprehensive testing from a single unit.
-
Product
PICMG® 2.11 47-pin Hot-Swap Redundant 3U CompactPCI® 8HP 250 W Power Module
cPS-H325/110
-
- PICMG® 2.11 CompactPCI® Power Interface compliant- Internal OR-ing Diodes for N + 1 redundancy- PICMG® 2.11 47-pin CompactPCI® in-rack power module interface- 250 W DC output- Active PFC (Power Factor Correction) meets IEC1000-3-2 Harmonic Correction
-
Product
1-phase Power Analyzers
-
PeakTech Prüf- und Messtechnik GmbH
Is a high-precision energy cost measuring device for recording the energy consumption of electrical devices and for calculating the current consumption of a device by entering the electricity price. Thanks to the integrated power factor calculation, all modern consumers such as Switching power supplies, TV sets, fluorescent lamps, LED systems and of course ohmic loads such as Electric heaters and hobs can be measured accurately. In addition, the high resolution, the low response characteristic and even very small or stand-by consumers from approx. 1 W can be measured.
-
Product
Three Phase Meter Test Bench
-
Supreme Instrument Laboratories
Three phase meter test bench suitable for calibration & testing of AC Ammeters, Voltmeters, Single phase Energy Meters, Watt Meters, Power Factor Meters, Three Phase Two Wire & Three Phase Four Wire Energy Meters Trivector Meters, Maximum demand indicators, of active & reactive systems, Three phase 3 wire & 4 wire watt meters, Var Meters, Power Factor Meters etc.
-
Product
HID Ballast Tester
WT2000-HID
-
• Input Parameters Measurement: 1) Test voltage, current, power, power factor, power line frequency, total harmonic and 0~50 harmonic 2) Range of voltage and current basic wave frequency: 45Hz~65Hz 3) Range of narrow frequency: 45Hz~5kHz 4) Range of wide frequency: 45Hz~1MHz
-
Product
M-Power-line
-
The M-Power-Line convinces with its robust design, high efficiency, compact dimensions and excellent price-performance ratio. By using a Power Factor Controller (PFC) the input voltage may vary from 100V to 254V. This means that the devices can be used anywhere in the world regardless of the typical national power supply system. The simple operation and easy readability of relevant characteristic values (target/actual/state/alarm message) make the devices particularly attractive for use in many branches of industry as well as research institutes.
-
Product
Measuring Display Unit Breakers
-
Mitsubishi Electric Automation, Inc
Measuring display units (MDU) are integrated with molded-case circuit breakers and earth leakage circuit breakers for measuring, displaying, and transmitting information on cable ways. This display unit closely monitors energy consumption by measuring current, voltage, power, electric energy, harmonic current, leakage current and power factor.
-
Product
3-Phase Power and Energy Analyser
PQ55A
-
* Cpmprehensive real-time monitoring, recording and analysis of 3-phase systems* Voltage measurement (true RMS)* Current measurement (true RMS)* Power factor measurement* Phase angle measurement* Power analysis (active, apparent and reactive power)* 4. Current clamp for neutral line current measurement* Suitable for use in housing construction, offices and small businesses
-
Product
TRMS AC/DC Clamp-on Power
HT9023
-
HT9023 has been designed to measure AC, DC AC+DC current up to 1000A in TRMS reaching CAT IV 600V and CAT III 1000V in compliance with safety standard IEC/EN61010-1. The clamp also measures DC voltage up to 1500V, AC, AC+DC voltage up to 1000V, Active, Reactive and Apparent Power, Power Factor, Energy, voltage/current harmonic analysis up to the 25th with THD% calculation in balanced single-phase or three-phase systems.
-
Product
Portable Three-Phase Phantom Load
EE-120A-3 + EE-500V-3
-
The Phantom Load is able to generate three-phase voltages and currents with unprecedented stability and measurement accuracy. The amplitude and phase-shift of each current and voltage is individually adjustable. The generated values of voltage, current, power, power factor, phase shift, THD and frequency are indicated on the LCD display.
-
Product
Power Factor Controllers
-
ENTES Reactive Power Factor Controllers try to match the system''s power factor which is defined as the ratio of the active power to the apparent power to the user defined power factor value by controlling the facility''s reactive power using capacitor banks.
-
Product
Three Phase Portable Energy Meter Test Instrument Type KP-P3003-C
-
Bofa Instrument & Equipment Co., Ltd
Three-phase portable energy meter test instrument type KP-P3003-C with current and voltage source is an ideal device to test all kind three-phase energy meters accuracy below 0.2. The equipment can generate 3-phase voltage, 3-phase current and any power factor signal, the standard meter inside the equipment is class 0.05. The equipment is box structure, light, and easy to carry, it is very convenience to test meters on site, moreover the equipment can be used for testing meter in meter manufacture and as testing equipment in R&D institute.
-
Product
504W - Single Output
PFH Series
-
*2.4" x 4" Brick Footprint with Metal Case*85 - 265VAC Input*12, 28, or 48VDC Output; 12V Aux*High Power Density, High Efficiency*Power Factor Corrected*Suitable for Conduction Cooling*PMBus™
-
Product
Automatic Batteries with Filters with Thyristors
BATLVFS1000
-
Lifasa - International Capacitors, SA
LIFASA automatic capacitor banks are used for centralized compensation of power factor in low voltage instalations.
-
Product
Pump Testing Panel
VPTP
-
It covers No Load Test, Block Rotor Test, Pump Performance Test, Reduced Voltage Test for Submersible Pump, Monoblock Pump & Centrifugal Pump etc. Direct measurement of Voltage, Current Active Power, Power Factor (PF), Apparent Power, Frequency, Head, Suction, Discharge, RPM, Corrected RPM, %Slip.
-
Product
Resistive Load Banks
R Series
-
Load banks are devices which contain resistive, inductive and/or capacitive loads, apply the load to an electrical power source and dissipate the power of the electrical source. Portable and stationary resistive load banks incorporate as low as 1 kW load step increments for testing small to large generating sets. The fine control resolution ensures accurate load control and power factor targeting adjustments.
-
Product
Power Management
-
Innovative power management products that enable energy efficient solutions across all applications by providing improved power factor, enhanced active-mode efficiency, and reduced standby-mode power consumptions.
-
Product
Resistive & Capacitive AC Load Bank
RCD
-
RCD AC load banks are used to test the REAL working condition of UPS, rectifier, inverter and etc who are loaded by non-linear or electronic load with non-constant resistance such as computer, networking equipments and etc. Through the accurate detection of its output and power quality, users could avoid the inadequate loading capacity or cause pollution to power grid, so as to guarantee supply security. JUNXY RCD load banks leading power factor loads are created to debug power supply system parameters such as its crest factor test.
-
Product
Power Meter
PM-10,PM-15
-
Standard Electric Works Co., Ltd
● Determine the running cost your appliances.● Make informed decisions when purchasing appliances and equipment.● Reduce your electricity bill.● Measure Voltage, Current, Power, Volts, Amps, Power Factor, and Greenhouse Gas Emissions.● Calculate electrical expenses by day, week, month, and even an entire year.
-
Product
Digital Panel Meter
MPF-5A
-
Mx-5A meter to provide power (Watt or Active Power or Re-active Power or Power Factor), high-precision measurement, display and remote communication capabilities.Additional purchase: 1 group of relay outputs, 1 analog output, an RS485 communication output (the Modbus RTU Mode) interface, so that can be installed in power management, remote input and output, alarm and variety of remote communication control the use of needs.120mm (D) is ideal for assembling in panels with limited penetration depth
-
Product
Power Meter
8015 PM
-
Standard Electric Works Co., Ltd
● Determine the running cost of your appliances.● Measure voltage, current, frequency, watt, power factor, and greenhouse gas emissions.● Optical USB to RS-232 data transmission.● 2 Optical LEDs are built-in for data transfer.● Transferring and showing real-time data to a PC.● Make informed decisions when purchasing appliances and equipment.● Reduce your electricity bill.● Calculate electrical expenses by real, hour, month. ● Can make different kinds of plugs for different countries / areas, such as Type B, E, G, I plugs.....etc.● Data communication function.● Freely set upper and lower limit for V,A,W and alarm when measured value is out of limit.● Backlight function.
-
Product
LED Lighting Test Instrument Integrating Sphere
CX-I.5S
-
Shenzhen Chuangxin Instruments Co., Ltd.
Measure Luminous Flux, Luminous efficacy, radiant power, Spectral Power Distribution, Chromaticity Coordinate, Correlated Color Temperature, Peak Wavelength, Dominant Wavelength, Spectral Half Width, Color Rendering Index, Colorimetric Purity, red ratio, Standard deviation of color matching(SDCM), voltage, current, power, power factor, harmonics, and etc. It meets the requirements of CIE standards.
-
Product
AC/DC Power Clamp Tester
IBL-307
-
International Biological Laboratories
This Digital Clamp On Power Meter Model 307 can be used to measure True Power, Apparent Power and Power Factor in single phase circuits. It measures AC/DC Current and incorporates a frequency counter. It is autoranging type Digtal Clamp On Power Meter and has 3-3/4 Digits 4000 Counts with 40 segment analog bargraph LCD Display.
-
Product
Programmable AC Electronic Load
63800
-
Chroma Systems Solutions, Inc.
The Chroma 63800 Loads can simulate load conditions under high crest factor and varying power factors with real time compensation even when the voltage waveform is distorted. This special feature provides real world simulation capability and prevents overstressing resulting in reliable and unbiased test results.
-
Product
Power Analyzer
PW3390
-
The PW3390 delivers 4 input channels and ±0.04% basic accuracy for power - the top instrument in its class. Achieve more precise measurements of the power and efficiency of high efficiency equipment used in power electronics. Further, a 200 kHz measurement band and flat amplitude and phase characteristics up to high frequencies enable the precise measurement of power at top frequency levels and low power factor.
-
Product
Low Voltage Capacitor Banks
-
Wide range of capacitor banks to correct the power factor in low-voltage electrical installations, for both 50 Hz and 60 Hz networks. Avoid surcharges on the electric bill and improve the capacity of the installation.
-
Product
Wideband Power Analyzer
2335A
-
Clarke-Hess Communications Research
The Model 2335A Wideband Power Analyzer is a precision, high accuracy, high frequency auto-ranging instrument which measures and displays true rms Voltage, true rms Current, and true mean Power over a frequency range from dc to more than 1MHz. Full scale Current and Voltage inputs are typically measured within 0.1% of the amplitude reading to at least 500kHz. The corresponding Power is typically measured to within 0.1% of the input Volt-Amperes to 250kHz and to within 0.2% of the input Volt-Amperes to 500kHz for loads having any Power Factor.
-
Product
Transformer Performance Tester
JYW6100
-
JYW6100 Transformer No-loads and On-loads tester power factor tester is suitable for loss testing of low power factory transformer such as amorphous alloy transformer, with high precision and data loc
-
Product
RC-50 Artificial Phantom Load with Power Factor
480
-
The RC-50 Artificial Phantom Load with Power Factor (Catalog No. 480) has been re-designed to meet the most exacting requirements. It operates from a single phase source and will deliver current at either unity or 50% power factor at all full load ranges.
-
Product
Injection Transformer
J2101A
-
The injection transformer is presently the prevalent method for connecting the network analyzer to the circuit being tested, and is primarily used for control loop stability measurements. The goal of the transformer is to inject a signal into the control loop being measured, without impacting the performance of the loop. In order to accomplish this to a reasonable degree, The transformer is isolated and therefore is capable of floating on a high voltage, such as a Power Factor Corrector (PFC), which is often close to 400VDC. Measuring voltages that exceed the voltage rating of the FRA inputs require attenuation probes.
