Inductor Test
-
Product
DC Load Simulating Inductors
-
Osborne has developed a wide range of DC load simulation inductors that are known for the transients they produce. Osborne DC load simulation inductors are unique and innovative because they are engineered to produce a precise time constant current transient during the current charge cycle.Another distinguishing feature of our load simulation inductors is that they produce a precise voltage transient during the current discharge cycle. The resulting test circuit can be used to accurately replace real loads in a variety of circuit simulation applications.
-
Product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196A
-
The 16196A surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results - reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement - now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
Product
Conformance Test System
TS8980
-
The R&S®TS8980 is the most compact full range conformance testing solution on the market for testing in line with requirements from GCF, PTCRB and regulatory bodies. It supports the entire device certification process for RF and RRM, covering the widest range of technologies including 5G NR based on 3GPP and carrier acceptance specifications. The test system is available in various configurations to cover the required scope of testing.
-
Product
In-Circuit Test
TestStation LH
-
The TestStation LH in-circuit test system is a lower-cost, small footprint, feature scalable version of Teradyne's popular, award winning TestStation product family. TestStation LH features SafeTest protection technologies for accurate, reliable, and safe testing of the latest low-voltage technologies.
-
Product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196B
-
The 16196B surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results, reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement. Now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
Product
VLSI Test System
3380D
-
The 3380D/3380P/3380 test system have 4 wires HD VI source and any-pins-to-any-site high parallel test (multi-sites test) functions (256 I/O pins to test 256 ICs in parallel) that can meet the upcoming higher IC testing demands.
-
Product
Test System Optimized for High Volume Production Testing of Integrated Circuits
ETS-364 / ETS-600
-
The ETS-364 is a general-purpose precision analog and mixed-signal test platform designed for high volume production testing of integrated circuits; optimized for high throughput applications with a fully integrated multisite software and hardware architecture. The test system offers separate floating resources for each site, improving site isolation and measurement accuracy coupled with digital instrumentation enabling the most efficient, high-volume testing available. The system supports up to 240 analog pin channels, and offers 133 MVPS digital vector rate with up to 128 digital pin channels. Eagle's scalability includes the ability to double the capacity of an ETS-364, providing more than 480 analog pin channels and up to 256 digital I/O pin channels with the ETS-600.
-
Product
Memory Test System
T5851/T5851ES
-
The T5851 system is designed to provide a cost-effective test solution for evaluating high-speed protocol NAND flash memories including UFS3.0 universal flash storage and PCIe Gen 4 NVMe solid-state drives (SSD), both of which are expected to be in high demand for the LTE 5G communications market.
-
Product
Fully-Automated CTIA-Compliant OTA Test System
TS8991
-
The R&S®TS8991 OTA performance test system measures the spatial radiation and sensitivity characteristic as specified by CTIA and 3GPP.The system software provides ready-to-use test templates for OTA measurements and supports all wireless standards.The integrated report function collects all measured test data such as graphics or numeric results, test environments, EUT information and hardware setup in one document.
-
Product
Inductor Coils
-
SemiGen's Inductor Coils are manufactured using our thin film process on quartz substrates. The precision photolithography and non-chemical etching process provides clean edges to assure uniformity from coil to coil. By using quartz and applying a polyimide coating we produce a device that eliminates the need for conformal coating or staking. Inductors can be epoxied down with nonconductive epoxy and the wire bonded for connection.
-
Product
Inductor Tester
-
An impulse can be applied to the coil of a chip power inductor to perform insulation tests (surge tests) within the windings.
-
Product
Positioning Test System
TS-LBS
-
The R&S®TS-LBS is a comprehensive test solution for network and satellite based location technology testing of wireless devices and chipsets.It is highly configurable for testing various location technologies and uses Rohde & Schwarz location based test systems.The R&S®TS-LBS test system family fulfills the requirements of LBS conformance testing and operator acceptance testing on GSM, WCDMA, LTE and 5G devices and chipsets as well as regulatory testing consisting of adjacent channels and spurious emissions for EN 303 413 receiver testing. It also fulfills the requirements of E112 (EU) 2019/320 testing consisting of GNSS testing such as Galileo and AML mobile testing.
-
Product
Semi-Rigid Cable, 3.5 Mm (Test Port) To 3.5 Mm
85131G
-
The Keysight 85131G is a 53 cm (21 in) long1 semi-rigid cable with a 3.5 mm female2 to 3.5 mm male connector. Cable frequency range is dc to 26.5 GHz with a return loss of 16 dB or better. Insertion loss is 0.3 * sqrt (f) + 0.2 dB (where f is frequency is GHz) for the test port connector, and 1.8 dB at maximum frequency for the device connector. Phase stability of semi-rigid/flexible cables is characterized with a 90 degree bend using a 4 inch radius. Stability1 of the Keysight 85131G is 0.06 dB and phase is 0.16o * f + 0.5o (where f is frequency in GHz).
-
Product
Antenna Test System
ATS1000
-
Offering measurements on active and passive devices - supporting also extreme temperature testing. 5G is all about data, speed and reliability using high frequency millimeter wave bands. The lack of conventional external RF connectors makes 5G antenna characterization challenging. 5G antenna, chipset and UE manufacturers as well as wireless market operators need a viable solution for research, diagnostics and debugging up to type approval.
-
Product
Design for Testability (DFT Test)
-
Corelis can provide you with design consultation and an analysis of your design for boundary-scan testability. We will review your design and make specific recommendations that if implemented will improve the testability. We can also suggest improvements that will increase test coverage and allow boundary-scan to be implemented in a more cost-effective manner.This service also includes a DFT test coverage analysis that we recommend to do after schematic capture and before PCB layout. At this stage of product development, Corelis provides you with a comprehensive test coverage reports that identifies all of the boundary-scan nets and pins and classifies them as completely tested, partially tested, or not tested. The report also recommends where to add test points (pads) for physical “nails” access if additional test coverage is required.
-
Product
Inline test system for FCT, ICT, ISP and Boundary Scan for Automated Operation
LEON InLine
-
High production volume often requires inline solutions with fully automated product Handling – the LEONlnline is a complete Inline Board Test Solutions for printed circuit boards. It integrates a flexible and scalable test system that features an excellent signal integrity and a high-quality fixture interface. This is achieved by combining a cableless connection from ABex modules to Virginia panel interface connectors.
-
Product
In-Line RF Test Platform
AR925
-
This functional and RF test platform combines outstanding productivity with substantial equipment savings. The Faraday chamber of the fixture comes with an interchangeable cassette to minimize the testing cost of each new product
-
Product
Test Instruments
-
Test instrumentation from COTS to custom, including VXI, PXI and LXI-based platforms.
-
Product
Molded Inductors
-
Molded inductors are constructed by pressing or molding a magnetic material around a pre-wound coil and lead-frame to form the inductor. Our molded inductors provide a fully shielded, high energy density, soft saturation solution for applications up to 110Apk. The construction enables low profile solutions in a cost effective and robust solution that minimizes acoustic noise. We offer a high saturation current series (commercial and automotive, -40C to 125C) and a low DCR series (automotive, -55C to 155C) in a wide range of platforms from 4x4x1.2mm up to 24x24x13mm.
-
Product
RF Testing Platform for ATx05
AT118
-
The functional test of modern devices with wireless connectivity always requires RF isolated cameras, as the only way to have the parameters controlled and to guarantee operation under the specified conditions.
-
Product
Functional Test Trainer System
QT65
-
Qmax Test Technologies Pvt. Ltd.
Functional Test Trainer system, is a test system which can perform various Power- On functional tests of digital devices(ssl/MSI/LSIs and analog devices in the out- circuit and in-E conditions. Unified Library of vast number of devices to effectively test devices in in-circuit as well as out of circuit conditions.
-
Product
EBIRST 200-pin LFH To 96-pin SCSI Adapter Cable
93-002-226
-
eBIRST adapters allow extension to other switching system connectors, including SMB
-
Product
NI's Electrical Functional Test Solution
-
PXI instrumentation ensures complete and accurate test coverage with a modular architecture mounted in ultra-reliable PXI chassis.TestStand and LabVIEW software provide rapid development of complex test steps and sequences. PXI systems conserve floorspace because of their small, light form factor. Order them preassembled and installed using NI ATE Core Configurations.SystemLink™ software deploys updates and democratizes data insights to optimize operational efficiency.
-
Product
Test Platforms
-
Leverage 20+ Years of Test Industry Experience with Built-In IP for Maximum Reuse
-
Product
TestStand
-
TestStand is industry-standard test management software that helps test and validation engineers build and deploy automated test systems faster. TestStand includes a ready-to-run test sequence engine that supports multiple test code languages, flexible result reporting, and parallel/multithreaded test.
-
Product
Functional Test Fixtures
-
Reliable connections to device under test (DUT) test points are essential for robust functional test. Bloomy provides rugged fixtures and cable sets (ITAs) built for thousands and thousands of cycles in manufacturing environments. With the industry’s best mass interconnects and internal electronic keying, our fixtures are easy to change out and are automatically recognized by the test system.
-
Product
Functional Test System Optimized For Real-Time Digital Bus Test
Spectrum HS
-
Spectrum HS is Teradyne’s fully integrated functional test system. Optimized for real-time test of low latency buses, it’s a high-performance system delivering excellent test coverage of current and future products.
-
Product
NFC Conformance Test System
T3111S
-
The T3111S RIDER NFC Conformance Test System is the Keysight solution for RF Analog and Digital Protocol testing of NFC, EMV and ISO devices. The Test System is based on the Keysight T1141A NFC Test Set and it is complemented by the Keysight's or FIME's robots for accurate and repeatability RF testing. Selected 3rd party positioning robots can also be supported.
-
Product
6TL08 Benchtop Test Platform
H710008
-
The 6TL-08 base platform was designed to cover the most common testing and in-system programming (ISP) needs with a reduced initial budget. The system includes a robust manual linear push mechanism allowing a low-cost fixture strategy thanks to the exchangeable cassettesThe platform enclosure features an 8-Slot fixture receiver, compatible with VPC 90 Series Mass Interconnect Module, as well as 6TL intelligent YAVModules (YAV90MMU &YAV90059), with room for fast ISP devices, optional PXI chassis and various power supplies. A removable back panel allows easy placement of custom connectors or test auxiliary circuitry.
-
Product
Automatic Test System
-
Automatic Test system is the ultimate solution for power electronic testing. The system includes a wide range of hardware choice such as AC/DC Sources, Electronic Loads, DMM, Oscillate Scope, Noise Analyzer and Short /OVP Tester. This flexibility combined with its open architecture software platform-PowerPro III, gives users a flexible, powerful and cost effective test system for almost all types of power supply testing.
