Product

High Voltage Insulation Tester Module

DP-cPCI-5586

-

Data Patterns Pvt. Ltd.

DP-cPCI-5586 - Data Patterns Pvt. Ltd.

DP-cPCI-5586 is a High Voltage Insulation Tester Module. This module facilitates single-board voltage source/measurement features with high voltage output and a nanometer. Occupying a single slot in standard cPCI rack, this module can be used for multiple point cable harness test systems with limited rack space. Applications of this board include automatic test equipment, checkout systems, force voltage measure current, and insulation test.

Product

AC/DC Power Supply 25 W

CFM25S120-T

-

ELMA Electronic, Inc.

CFM25S120-T - ELMA Electronic, Inc.

AC/DC power supply with 25 W from Cincon | input ranges 90 - 264 VAC | output 12 V | operates in temperature from -30 to +70 °C | class II | wafer version

Product

Voltage Dividers

-

Measurements International Ltd.

Measurements International Ltd.

A series of resistors or capacitors which can be tapped at any intermediate point to produce a specific fraction of the voltage applied between its ends.

Product

High Voltage System

HV-2

-

International Electro-Magnetics, Inc.

HV-2 - International Electro-Magnetics, Inc.

*Tests Power Transformers for Continuity, Ratio and Phase. Applied and Induced Potential and No-load Losses.*14 Conductor Switching Matrix will test 7 individual windings, 13 taps of one common winding or some combination thereof. (10 Amp current limit)*The System Control is Windows/Visual Basic based. Menu screens allow full selection of test parameters and sequence. Low voltage tests can be performed first, allowing defective parts to be rejected without proceeding to time consuming induced Potential dwell routines. Test data labeling and data acquisition software can be easily added to the system.

Product

SCR Controlled DC power Supplies

-

Carl E. Holmes Company

Carl E. Holmes Company

Variable DC power supplies are AC to DC power supplies with a variable DC output. The output can be varied with an SCR controller. The AC input power can be single-phase or three phases. With single-phase AC input, the DC output ripple is very high (50%). With three-phase AC input, the DC output ripple is low (5%). This would be a key benefit for selecting three-phase AC input instead of a single phase.

Product

High Power Optical Head With Integrating Sphere

81628C

-

Keysight Technologies

81628C - Keysight Technologies

The 81628C High-Power Optical Head features an integrated sphere that enables it to handle power levels up to +40 dBm (with heat sink), across 800 nm to 1700 nm wavelength range. It provides the highest accuracy at high power within the family.

Product

High Voltage Surge Testers

HVST

-

Test Electronics

HVST - Test Electronics

The most important features of the surge tester are its ability to test the entire winding insulation system. A high voltage surge generates turn to turn, coil to coil, and phase to phase voltage stress, as well as ground insulation stress. When used as a dielectric test, accurate voltage readings are essential. The HV Surge Tester monitors the voltage directly across the winding under test. This voltage is displayed on an oscilloscope and recorded on the Pass/ Fail LED latch monitor. This voltage will be accurate despite the impedance of the winding being tested. The insulation system can be tested way above the operating voltage because of the brief duration of the applied voltage test pulse. This allows faults to be detected long before they become apparent at operating conditions.

Product

Power Supply Test System

-

Intepro Systems

Intepro Systems

The Procyon PTS 2100-10 is a configurable turnkey Power Test System, delivering automated test equipment (ATE) to some of the world’s largest-volume manufacturers as well as the affordability needed by niche market producers. Aerospace, defense, and avionics power supply ATE test systems applications include functional testing of AC and DC power supplies, generator, and engine control units, as well as a wide range of associated electronics.

Product

DC Power Supplies

-

Intepro Systems

Intepro Systems

Intepro Systems offers a wide selection of Auto-Ranging programmable DC Power Supplies. Each DC Power Supply are MOS-FET based, resulting in a high performance power stage that offers high speed slew rates and low output ripple.

Product

AC/DC Power Supply 50 W

HBU50-109

-

ELMA Electronic, Inc.

HBU50-109 - ELMA Electronic, Inc.

AC/DC power supply with 50 W from Sinpro | input ranges 80 - 275 VAC | output 32 V | operates in temperatures from -10 to +70 °C | provides 2 MOPP protection

Product

Power Supplies

6306D-10

-

Topward

6306D-10 - Topward

0-30V/0-6A, 5V/5A Triple, Digital, 10-turn V control

Product

Voltage Stabilizer

MS 7643

-

Meltronics Systemtech

MS 7643 - Meltronics Systemtech

VSTAB is a voltage stabilizer, regulates the incoming supply +28V voltage into the required +15V. The electrical specifications meets MIL704 standard. Over load and short circuit protections are provided. Voltage stabilizer Module is a part of shipborne unit and it is meant for ensuring the power supply of the devices of this unit when fed from DC mains with nominal voltage of 28 V and variations of voltages from minimum 16V to maximum 32 V. The power consumption is 45 watts. The module is subjected to Qualification Tests as per MIL-STD-810G.

Product

High Voltage Optically Isolated Probes

-

Teledyne LeCroy

Teledyne LeCroy

High Voltage Optically Isolated Probes are designed to aid in device characterization measurements. Whether it is low or high voltage signals sitting on HV busses, high bandwidth, extreme precision, and optical isolation means floating measurements are easily made with minimal DUT loading.

Product

Continuity of Insulation Tester (High Voltage Method)

ZGQ-16B

-

Shanghai Dean Electrical Co., Ltd

ZGQ-16B - Shanghai Dean Electrical Co., Ltd

Executive standard: GB/T4074.5-2008/IEC60851-5;Inspection standard: JB/T4279.13-2008Meet GB/T6109-2008 standard requirementsUsed to test the Insulation continuity (namely the pinhole number of enameled wire sample per unit length) of enameled round wires with nominal conductor diameter ranging from0.05mmto1.60mm;8 level test voltages can be selected by pressing button: 350V, 500V, 750V, 1000V, 1500V, 2000V, 2500V and 3000V;Test length ranging 0～99m;Application of SCM control.Automatically complete test process, display wire testing length and pinhole number;Brushless driving motor, guide pulley and take up pulley are equipotent.The electrode insulation to ground, using high resistance material of non-hygroscopic, no leakage, no tracking, easy to clean, Insulation thickness can ensure long-term 3000V voltage effect.Circuit board is subject to anti-static and moistureproof and long-time aging treatment, has more stable quality and higher durability;

Product

High Voltage (Hipot) Cable Tester

CH2

-

Cirris Systems Corporation

CH2 - Cirris Systems Corporation

The easy-wire CH2 was designed for commercial, military, and aerospace applications. Running on powerful Windows-based software, the CH2 offers unrivaled testing capabilities at an unparalleled price. Compact, easy-to-use, and FAST (shorts/mis-wires detected in <1 sec for 20,000 points), the CH2 is positioned to become the ''''tester of choice'''' for high-end users.

Product

Programmable Switching Power Supplies

-

PeakTech Prüf- und Messtechnik GmbH

PeakTech Prüf- und Messtechnik GmbH

In addition to presets for current and voltage values, time programs with intervals and the number of runs can also be created directly on the device or using the included PC software. For operation with a PC, the switching power supply is equipped with a USB and RS-485 interface. A PC connected to the RS-485 interface enables the control of up to 32 power supplies. A USB interface on the back of the device connects to a Windows PC. The intelligent fan control adjusts the speed of rotation to the respective temperature and output power. The output voltage and current limit can also be set in the open circuit without a connected load. Due to its high reliability and the programming functions, this power supply series is ideal for professional users from industry, control and regulation technology or the electronics laboratory.

Product

Triple Channel DC Linear Power Supply

MPS-X Series

-

Matrix Technology Inc.

MPS-X Series - Matrix Technology Inc.

Triple channel programmable DC power supply is with high resolution, high precision and high stability, over-voltage and over-heat protection are available. Series and parallel operation are also provided. The resolution is 1 mV/1 mA

Product

AC High Voltage Tester

VHT

-

Veer Electronics

VHT - Veer Electronics

VEER make High Voltage Tester VHT is specially designed to test Dielectric Strength of Device under Test as per applicable standards. High Voltage test is required to determine whether test object has proper insulation or not. High Voltage test is carried out as Routine Test Each device is subjected to test at high voltage of 1 kV + 2 x (working Voltage)If Insulation is weak then device will consume more power because of leakage current which causes more heat. Heat will reduce the reliability and overall life of device under test It is also responsible for high risk of electric shock. So, High voltage test is necessary for all electrical equipments.

Product

NIM and CAMAC Power Supplies

-

W-IE-NE-R, Plein & Baus GmbH

W-IE-NE-R, Plein & Baus GmbH

NIM and CAMAC crates require very clean and stable DC supplies with the standard voltages +24V / -24V, +12V / -12V and +6V / -6V. Consequently CERN defined compatible power supplies for both standards within their NIM and CAMAC specs., i.e. CERN spec. power supplies can be used on both types of crates. All "CE" version power supplies are outfitted wth separate AC wiring to comply with CE/UL safety standards.