-
Product
Digital Ultrasonic Flaw Detector
-
Are modern age portable and processor-based flaw detectors. They are made up of parts including an ultrasonic transducer, hardware & software for capturing signals and analysing them, a data logging module, and a waveform display for viewing the images and graphs.
-
Product
NI-9421, 24 V, 8-Channel (Sinking Input), 100 µs C Series Digital Module
NI-9421 / 779002-01
Digital Module
24 V, 8-Channel (Sinking Input), 100 µs C Series Digital Module - The NI‑9421 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each channel is compatible with 24 V logic levels and has an LED indicating the state of that channel. The NI‑9421 offers isolation between the input channels and earth ground.
-
Product
NI-9435, ±5 VDC to ±250 VDC/10 VAC to 250 VAC, 4-Channel (Sinking/Sourcing Input), 3 ms C Series Digital Module
779010-01
Digital Module
±5 VDC to ±250 VDC/10 VAC to 250 VAC, 4-Channel (Sinking/Sourcing Input), 3 ms C Series Digital Module - The NI‑9435 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each channel accepts signals from ±5 VDC to ±250 VDC and 10 VAC to 250 VAC; features transient overvoltage protection between the input channels and earth ground; and has an LED that indicates the status. The NI‑9435 is a correlated digital module, so it can perform correlated operations, triggering, and synchronization when installed in a CompactDAQ chassis.
-
Product
High-Voltage Amplifier
ZET 420
-
The high-voltage signal amplifier for emission of acoustic signals through capacitive emitters: sonic detectors (without integrated amplifiers), piezoelectric emitters, and transducers.
-
Product
Structural Test ICP® Accelerometers
-
Conventional structural test data systems use few to several hundred sensors. Cables bundles can be complex and confusing resulting in setup errors. Sensors with TEDS (Transducer Electronic Data Sheet) allow for an internal sensor digital chip to store sensor information. This information contains descriptive identifiers that when connected to a TEDS compatible signal conditioner or data system, reads the descriptive information and automatically aligns the data system. Human error is minimized, reducing time consuming data verification or re-test. The Series 333 ICP® accelerometers, and their accessories, are designed to address the needs of multi-point modal and structural test measurement applications. This equipment was developed in conjunction with the world renowned University of Cincinnati Structural Dynamics Research Laboratory and proven in real-world testing situations. The PCB 333 Series accelerometers delivers rapid system setup, reduces human documentation errors, maintains calibration data of each sensor, allows for “Plug-and-Play” installation, reduces overall test time lowering project test costs.
-
Product
Portable Switchgear Partial Discharge
PD-SG1
-
The PD-SG1 is a dual transducer Switchgear PD detection instrument. The unit detects TEV signals generated by internal discharge, as well as acoustic discharge generated by surface tracking or corona.
-
Product
Output Signal Cable
CO20-x
-
The Output Signal Cable CO20-x is a specialized accessory designed specifically for the F3B analog magnetic field transducers. This product enhances the performance and versatility of the transducers, which have been improved and developed to work seamlessly since January 2023. The CO20-x cable facilitates reliable signal transmissions, critical for accurate measurements in various applications.This cable features a robust design with a shield that is connected to the metal case of the connector, ensuring minimal interference. The end wires of the signal cable are intentionally left unterminated and are thinned to approximately 3 - 4 mm, allowing for customization. Users can easily terminate the ends with standard banana plugs as needed. Furthermore, the cable boasts an M12-8L-S-X, 8-pin male connector, which promotes compatibility and efficiency in signal transmission. The detailed specifications and design considerations articulated make this cable a vital component in ensuring the optimal functionality of the F3B transducers.
-
Product
Button Load Cell
3000 Series
-
Button Load Cells are strain gage based transducers with temperature compensation and excellent overall performance. This type provides a range of capacities up to 150 kN or 30 klb with better than ±0.5% (full scale) non-linearity. Three tapped holes are provided on the underside for ease of mounting. Fully welded cover, amplified and digitised versions are available on request.
-
Product
Compact Pressure Transducers And Switches
-
Compact Baratron® capacitance manometers are ideal for space constrained applications. Compact pressure transducers provide an analog output proportional to pressure, while compact pressure switches provide a relay output based on pressure.
-
Product
Load Cells
-
A load cell is a sensor which transforms the load or force applied to it into an electrical signal. Load cell sensors are based on the strain-gauge principle i.e. a sensor whose resistance varies with applied force. They are the most widely used as load transducers in all areas of weight measurement from retail scales, the process industry and medical applications.
-
Product
Transducer Test System
TTS-030
-
For the generation of unique bond links the use of high-quality components is an essential precondition. Despite all care in the production of ultrasonic transducers again and again unexpected effects occur, which only manifest themselves in the use of those transducers and which also have the reason in the transducer itself.
-
Product
Power Frequency Transducer
PP1S
-
1. Measuring and conversion IEC 6882. Dielectrical strength IEC 688 4 KVac / 1 min.3. Impulse test ANSI C37.90 / 1989 IEC 255-3 5KV ( 1.2 x 50 us ) 3KA ( 8 x 20 us ) - current coil4. Surge test (ring wave) ANSI C37.90 / 1989 ( 3KV - 0.5us / 100KHz ) IEC 255-3 ( 2.5KV - 0.25ms / 1MHz )5. Adaptability for power system VDE 0110 6. Measuring reliability VDE 3540
-
Product
Temperature Transmitter
T4111
-
Transducer is designed for temperature measurement at C or F by means of an externaltemperature probe with Pt1000 sensor. Measured temperature is converted to linearized unified signal 4-20 mA. Measured values are displayed on LCD display. It is possible to switch OFF theLCD at all. Current loop has two-wire connection and requires power from evaluation device.
-
Product
Calometric Power Meter
M1-25M/XXE
-
The M1-25M/XXE series instruments are high precision broadband Calorimetric Sensors operating in millimeter and sub-millimeter wave range on a principle of substitution of microwave power by direct current power, using an autocompensating transistor transducer. Calorimetric Sensor is supplied with Calorimetric Power Meter M1-25M (measurement and indicator block), which provides PC connection via USB interface.Calorimetric Power Meter with Calorimetric Sensor provides accurate absolute power measurements in single mode and multimode waveguides (Metal Dielectric Waveguide) which could be a priority for terahertz physics and technology.
-
Product
Portable Power Factor Meter
ST-2000 Cos∮
-
Standard Electric Works Co., Ltd
● Principle : Phase angle sensing transducer● Rated Accuracy : ±3% phase angle● Scale : Power Factor：Lead 0 – 0.3 – 1.0 – 0.3 – 0 Lag Power Angle： Lead 90° – 0° – 90° Lag● Effective Power Factor Measuring Range : Lead 0.5 – 1.0 – 0.5 Lag● Scale Length : Approx. 135mm(5-3/8”)● Frequency Influence : Within ±1.5° phase angle at 45 to 65Hz
-
Product
Speaker Consulting
-
From 1993 Peter Larsen has worked as an independent consultant for leading loudspeaker factories all over the world. During his career the Ringradiator, a new Racetrack woofer and a 15mm Mobile receiver have been developed among several hundred other transducers. Complete High End enclosure systems and Monitors are among the latest additions.
-
Product
Digital Weighing Indicator | Process Meter | Panel Meter
-
Mantracourt’s digital weighing indicator and panel meter modules are compatible with a wide range of sensors and transducers, including volts, amps, temperature, frequency, speed, load, force, pressure, torque, LVDT, RVDT and many more. The digital architecture offers simple one-pass calibration and fast setup.
-
Product
Calibrator for Vibration Transducers
HD2060
-
Hand-held calibrator for vibration chains with frequency 15.915 Hz and levels 1 m/s² and 0.1 g, and frequency 159.155 Hz and levels 10 m/s² and 1 g. With LCD display.
-
Product
Wideband Power Amplifiers
-
Krohn-Hite Wideband Power Amplifiers are designed to meet today's industrial needs where wideband, precision performance is required. Applications include: meter calibration, piezo transducer driving, bridging applications requiring high input and low output impedance, low distortion ac power source, ion beam deflection, vacuum tube driver, ink jet testing and design and many more.
-
Product
Acoustic Transducer
RESON TC 1026
-
Ideal for taking long or short baseline measurements, the TC 1026 is a powerful communications transducer for transponder, telephone and acoustic telemetry systems.
-
-
Product
3-Phase AC Voltage Transducer
ENVIROMUX-PT3-600
-
Monitors and reports voltage of any 3 phase circuit. Remotely detect blown fuses or tripped circuit breakers. Three 600 VAC inputs, three 4-20 mA outputs. Inputs and outputs isolated from one another. Frequency: 50/60Hz. Maximum primary current: 600 volts. Accuracy: ±0.25% F.S. @60Hz. Output: 4-20 mA. "Zero" adjustment for accurate 0 VAC reading, and "Calibration" adjustment for frequency and voltage level. Powered by the ENVIROMUX-S420MA-24V. Regulatory approvals: UL, CUL, CE. Requires two ENVIROMUX-S420MA-24V to monitor three phases. Caution: installation should be performed by qualified electricians only. Make sure electrical service is disconnected before making any electrical connections.
-
Product
Sonar Transponder Module for Gavia AUV
-
THE SONAR TRANSPONDER MODULE (STM), is a module for receiving and retransmitting sonar signals which allows for a standard Gavia vehicle to be configured as a Sonar Training Target (STT) for ASW training purposes. The STM consist of a flooded transducer compartment, an electronic compartment and a hydrophone that is towed behind the Gavia AUV and is capable of simulating preprogrammed target characteristics. The STM is programmable to emulate different type of realistic submarine target sizes and speeds for cost effective and re-usable ASW training capability.
-
Product
Low Pressure Variable Reluctance Sensor
DP45
-
The Validyne DP45 Very Low Differential Pressure Transducer is designed for extremely low pressure measurement in the order of 1 inch water column. This instrument is used extensively in connection with flow measurements where dynamic response at low flow rates is required. Dynamic line pressure effects are minimized due to the combination of low internal volume, symmetrical construction, and small volumetric displacement inherent in the DP45 design.
-
Product
NI-9474, 30 V, 8-Channel (Sourcing Output), 1 µs C Series Digital Module
779003-01
Digital Module
30 V, 8-Channel (Sourcing Output), 1 µs C Series Digital Module - The NI‑9474 works with industrial logic levels and signals to directly connect to a wide array of industrial switches, transducers, and devices. Each channel is compatible with signals from 5 V to 30 V, features transient overvoltage protection between the output channels and earth ground, and has a LED that indicates the status. The NI‑9474 is a correlated digital module, so it can perform correlated operations, triggering, and synchronization when installed in a CompactDAQ chassis.
-
Product
Transducers For Photodiodes
-
Photodiodes convert incoming electromagnetic radiation into electrical charge carriers. If photodiodes are short circuited an electrical current (photocurrent) proportional to the incident radiation intensity (number of photons per second) is induced. These photocurrents are generally small and cover the range from femtoampere (fA) to microampere (µA). Signal transducers transform this weak photocurrent to robust standard signals for reliable data transmission and simple data acquisition.
-
Product
Instrumentation
-
Unholtz-Dickie designs and manufactures a variety of transducer signal conditioners, accelerometers, remote charge preamplifiers, vibration monitors & limiters, transducer testers, buffer amplifiers and other special purpose instrumentation accessories for vibration testing control and measurement.
-
-
Product
Torque Transducer
T12HP
-
One torque sensor, multiple functions only T12HP can do this. Its superior basic accuracy guarantees precise values over the entire measurement range. This results in the FlexRange capability that only T12HP can provide without the need to switch the measuring range like so called dual range sensors do.
-
Product
Pressure Transducers
-
The Variohm range of Pressure Transducers offer, low cost,custom and low volume manufacturing, high quality all stainless steel wettedparts, and use internal sensors designed for applications with demandingperformance requirements.
